To achieve the extremely high luminosity for colliding electron-positron beams at the future International Linear Collider (ILC) an undulator-based source with about 230 meters helical undulator and a thin titanium-alloy target rim rotated with tangential velocity of about 100 meters per second are foreseen. The very high density of heat deposited in the target has to be analyzed carefully. The energy deposited by the photon beam in the target has been calculated in FLUKA. The resulting stress in the target material after one bunch train has been simulated in ANSYS.
We attracted attention to some peculiarities of positron production for linear collider (ILC). The conversion system with many targets and low K-factor is our primary interest.
The design of the conversion target for the undulator-based ILC positron source is still under development. One important issue is the cooling of the target. Here, the status of the design studies for cooling by thermal radiation is presented.
The ILC baseline design for the positron source is based on radiation from a helical undulator to produce positrons in a thin target. Since the photon beam created in the helical undulator is circularly polarized, the generated positron beam is longitudinally polarized. Using a photon collimator upstream the positron target the positron polarization can be enhanced. However, the photon beam intensity yields a huge thermal load in the collimator material. In this paper the thermal load and heat dissipation in the photon collimator is discussed and design solutions are suggested.
The design of the positron source for the International Linear Collider (ILC) is still under discussion. The baseline design plans to use the high-energy electron beam for the positron production before it goes to the IP. The electrons pass a long helical undulator and generate an intense circularly polarized photon beam which hits a thin conversion target to produce $e^+e^-$ pairs. The resulting positron beam is longitudinally polarized which provides an important benefit for precision physics analyses at the ILC. In this paper the status of the positron target design studies is presented. Fo…
The design of the positron source for the International Linear Collider (ILC) is still under consideration. The baseline design plans to use the electron beam for the positron production before it goes to the IP. The high-energy electrons pass a long helical undulator and generate an intense circularly polarized photon beam which hits a thin conversion target to produce $e^+e^-$ pairs. The resulting positron beam is longitudinally polarized which provides an important benefit for precision physics analyses. In this paper the status of the design studies is presented with focus on ILC250. In pa…
To achieve the physics goals of future Linear Colliders, it is important that electron and positron beams are polarized. The positron source planned for the International Linear Collider (ILC) is based on a helical undulator system and can deliver a polarised beam with positron polarization of 60%. To ensure that no significant polarization is lost during the transport of the electron and positron beams from the source to the interaction region, spin tracking has to be included in all transport elements which can contribute to a loss of polarization. These are the positron source, the damping …
High energy e+e- linear colliders are the next large scale project in particle physics. They need intense sources to achieve the required luminosity. In particular, the positron source must provide about 10E+14 positrons per second. The positron source for the International Linear Collider (ILC) is based on a helical undulator passed by the electron beam to create an intense circularly polarized photon beam. With these photons a longitudinally polarized positron beam is generated; the degree of polarization can be enhanced by collimating the photon beam. However, the high photon beam intensity…
In order to achieve the physics goals of future Linear Colliders, it is important that electron and positron beams are polarized. The baseline design at the International Linear Collider (ILC) foresees an e+ source based on helical undulator. Such a source provides high luminosity and polarizations. The positron source planned for ILC is based on a helical undulator system and can deliver a positron polarization of 60%. To ensure that no significant polarization is lost during the transport of the e- and e+ beams from the source to the interaction region, precise spin tracking has to be includ…
The use of polarized beams enhance the possibility of the precision measurements at the International Linear Collider (ILC). In order to preserve the degree of polarization during beam transport spin rotators are included in the current TDR ILC Lattice. In this report some advantages of using a combined spin rotator/spin flipper are discussed. A few possible lattice designs of spin flipper developed at DESY in 2012 are presented.
The radiation damage of the positron source target for the International Linear Collider (ILC) has been studied. The displacement damage in target material due to multi-MeV photons has been calculated by combining FLUKA simulations for secondary particle production, SPECTER data for neutron displacement cross-sections and the Lindhard model for estimations of displacement damage by ions. The radiation damage of a stationary Ti6Al4V target in units of displacements per atom (dpa) has been estimated for photons from an undulator with strength 0.92 and period 1.15 cm. The calculated damage is 7 d…
The generation and capture of polarized positrons at a source with a superconducting helical undulator having 4.3 cm period and 500 GeV electron drive beam have been simulated. The positron polarization has been calculated for the different undulator K values (up to K = 2.5). Without applying a photon collimator, the maximal polarization of positrons is about 25% for 231 meters active magnet length of undulator with K = 0.7. Using an undulator with K = 2.5 and a collimator with an aperture radius of 0.9 mm results in increase of positron polarization to 54%. The energy deposition, temperature …
In the future the International Linear Collider (ILC), a helical undulator-based polarized positron source, is expected to be chosen. A high energy electron beam passes through a superconducting helical undulator in order to create circularly polarized photons which will be directed to a conversion target, resulting in electron-positron pairs. The resulting positron beam is longitudinally polarized. Since the photons are produced with an opening angle and pass through a long superconducting helical undulator, some of these photons will strike the undulator walls. Therefore photon masks must be…
The ILC positron system uses novel helical undulators to create a powerful photon beam from the main electron beam. This beam is passed through a titanium target to convert it into electron-positron pairs. The target is constructed as a 1 m diameter wheel spinning at 2000 RPM to smear the 1 ms ILC pulse train over 10 cm. A pulsed flux concentrating magnet is used to increase the positron capture efficiency. It is cooled to liquid nitrogen temperatures to maximize the flatness of the magnetic field over the 1 ms ILC pulse train. We report on prototyping effort on this system.
The positron source of the International Linear Collider is based on a superconducting helical undulator passed by the high-energy electron beam to generate photons which hit a conversion target. Since the photons are circularly polarized the resulting positron beam is polarized. At ILC250, the full undulator is needed to produce the required number of positrons. To keep the power deposition in the undulator walls below the acceptable limit of 1W/m, photon masks must be inserted in the undulator line. The photon mask design requires a detailed study of the power deposition in the walls and mas…
The International Linear Collider (ILC) is a 200-500 GeV center-of-mass high-luminosity linear electron-positron collider, based on 1.3 GHz superconducting radio-frequency (SCRF) accelerating cavities. The ILC has a total footprint of about 31 km and is designed for a peak luminosity of 2x10^34 cm^-2 s^-1. The complex includes a polarized electron source, an undulator-based positron source, two 6.7 km circumference damping rings, two-stage bunch compressors, two 11 km long main linacs and a 4.5 km long beam delivery system. This report is Volume III (Accelerator) of the four volume Reference D…
In the future, International Linear Collider (ILC), a helical undulator based polarized positron source is expected to be chosen. A high energy electron beam passes through a superconducting helical undulator in order to create circularly polarized photons which will be directed to a conversion target, the result of which, will be electron-positron pairs. The resulting positron beam is longitudinally polarized. In order to produce the required number of positrons in ILC250 the full undulator length is needed. Since the photons are created with an opening angle and traveling through a 320 m lon…
In the baseline design of the International Linear Collider (ILC) an undulator-based source is foreseen for the positron source in order to match the physics requirements. The recently chosen first energy stage with sqrt(s)=250 GeV requires high luminosity and imposes an effort for all positron source designs at high-energy colliders. In this paper we perform a simulation study and adopt the new technology of plasma lenses to capture the positrons generated by the undulator photons and to create the required high luminosity positron beam.
To realise a planned high-luminosity and high-energy $e^+e^-$-collider, as the ILC, a large amount of positrons have to be produced and the accelerated particles have to be captured and matched according to the damping ring acceptances. %There exist several technical possibilities. In this contribution a new promising alternative method for capturing positrons will be presented, the application of the plasma lens as an optical matching device. It will be compared with the current matching device proposed for the ILC, namely the quarter wave transformer. An advantage of the plasma lens is the d…
In the baseline design of the International Linear Collider (ILC) an undulator-based source is foreseen for the positron source. In this study the energy deposition in the pulsed flux concentrator (FC) of positron source is calculated for the ILC at 250 GeV center-of-mass energy. The peak energy of 33 J/g deposited by one beam pulse in the current design of the FC is above the limit for copper material. Several promising options were considered to solve the issue of overheating the FC: the quarter wave transformer (QWT) has a significantly bigger aperture and is considered as an valuable and s…
We discuss the basis of polarized positron production by low energy polarized electrons. Efficiency of conversion ~0.1-1% might be interesting for CEBAF facility and ILC as well.
A compact polarized positron source for Jefferson Lab is discussed. This scheme relies upon a high polarization (85%), high current (1 mA), low-energy (<100 MeV) electron beam to generate polarized positrons in a conversion target via polarized bremsstrahlung and pair creation. GEANT4 is used to simulate source distributions suitable for a CEBAF-like injector with positron polarization ~60% and nano-Ampere intensity. An experiment to test this scheme is outlined.
A novel concept for producing polarized positrons at Jefferson Lab using the CEBAF polarized electron photo-injector is presented. This approach relies on the polarization transfer from low energy highly polarized electrons to positrons via bremsstrahlung followed by pair production in a conversion target. An experiment to test this concept is discussed on the basis of GEANT4 simulations. It is shown that this low energy approach, which benefits from recent advances in high current high polarization electron sources, can yield positron longitudinal polarization up to 40%.
If a beam of unpolarized positrons (which is considered as a sum of two fractions with opposite helicities) passes through an intense circular polarized laser radiation these fractions may be separated. For high laser flash intensity each positron will interact with $k_0\gg$1 laser photons subsequently (linear multiple compton scattering process). Due to difference in the compton cross-section for positrons polarized in opposite directions the mean final energy of each fraction will be different. It allows to get a polarized positron beam using the momentum selection (with some intensity loss)…
The construction of the ILC tangential to Tevatron ring will give opportunity to investigate electron-proton, positron-proton, electron-antiproton, positron-antiproton interactions at 1 TeV center of mass energy. The analysis of the lepton-hadron collisions in these energy region is very important both for understanding of strong interaction dynamics and for adequate interpretation of future LHC and VLHC data. In addition, ILC-Tevatron collider will provide a possibility to realize photon-hadron collisions in the same energy region using Compton backscattered laser photon off ILC electron beam…
For a number of physical studies which are planned to be made with the next generation colliders, it is necessary to use polarized beams of both electrons and positrons. The problem of producing and acceleration of polarized electrons may be considered to be solved, but the existing approaches to create polarized positron beams do not ensure the parameters required. This work proposes a new approach to produce polarized positron beams, which is based on the process of multiple Compton backscattering of unpolarized ultrarelativistic positrons in the field of intense circularly polarized laser w…
Positron sources are critical components of the future linear collider projects. This is essentially due to the high luminosity required, orders of magnitude higher than existing ones. In addition, polarization of the positron beam rather expands the physics research potential of the machine. In this framework, the Compton sources for polarized positron production are taken into account where the high energy gamma rays are produced by the Compton scattering and subsequently converted into the polarized electron-positron pairs in a target-converter. The Compton multiple Interaction Point (IP) l…
In this contribution accelerator solutions for polarized beams and their impact on physics measurements are discussed. Focus are physics requirements for precision polarimetry near the interaction point and their realization with polarized sources. Based on the ILC baseline programme as described in the Reference Design Report (RDR), recent developments are discussed and evaluated taking into account physics runs at beam energies between 100 GeV and 250 GeV, as well as calibration runs on the Z-pole and options as the 1TeV upgrade and GigaZ.
This note summarizes the results of the "Workshop on Polarisation and Beam Energy Measurements at the ILC", held at DESY (Zeuthen) April 9-11 2008. The topics for the workshop included (i) physics requirements, (ii) polarised sources and low energy polarimetry, (iii) BDS polarimeters, (iv) BDS energy spectrometers, and (v) physics-based measurements of beam polarisation and beam energy from collider data. Discussions focused on the current ILC baseline programme as described in the Reference Design Report (RDR), which includes physics runs at beam energies between 100 and 250 GeV, as well as c…
The new method for producing of the polarized relativistic positrons is suggested. A beam of unpolarized positrons accelerated up to a few GeV can be polarized during a head-on collision with an intense circularly polarized lazer wave. After a multiple Compton backscattering process the initial positrons may lose a substantial part of its energy and, as consequence, may acquire the significant longitudinal polarization. The simple formulas for the final positron energy and polarization degree depended on the laser flash parameters have been obtained. The comparison of efficiences for the sugge…
An unprecedented positron average current is required to fit the luminosity demands of future $e^+e^-$ high energy physics colliders. In addition, in order to access precision-frontier physics, these machines require positron polarization to enable exploring the polarization dependence in many HEP processes cross sections, reducing backgrounds and extending the reach of chiral physics studies beyond the standard model. The ILC has a mature plan for the polarized positron source based on conversion in a thin target of circularly polarized gammas generated by passing the main high energy e-beam …
A possible solution to realize a conventional positron source driven by a several-GeV electron beam for the International Linear Collider is proposed. A 300 Hz electron linac is employed to create positrons with stretching pulse length in order to cure target thermal load. ILC requires about 2600 bunches in a train which pulse length is 1 ms. Each pulse of the 300 Hz linac creates about 130 bunches, then 2600 bunches are created in 63 ms. Optimized parameters such as drive beam energy, beam size, and target thickness, are discussed assuming a L-band capture system to maximize the capture effic…
We describe a scheme for producing polarised positrons at the ILC from polarised X-rays created by Compton scattering of a few-GeV electron beam off a CO2 or YAG laser. This scheme is very energy effective using high finesse laser cavities in conjunction with an electron storage ring.
Positron sources are the key elements for the future and current lepton collider projects such as ILC, CLIC, SuperKEKB, FCC-ee, Muon Collider/LEMMA, etc., introducing challenging critical requirements for high intensity and low emittance beams in order to achieve high luminosity. In fact, due to their large production emittance and constraints given by the target thermal load, the main collider parameters such as the peak and average current, the emittances, the damping time, the repetition frequency and consequently the luminosity are determined by the positron beam characteristics. In this p…
The Polarized Electrons for Polarized Positrons (PEPPo) experiment has demonstrated the efficient transfer of polarization from electrons to positrons produced by the bremsstrahlung radiation of a polarized electron beam in a high-$Z$ target. Positron polarization up to 82\% has been measured for an initial electron beam momentum of 8.19 MeV/$c$, limited only by the electron beam polarization. Combined with the high intensity and high polarization performances of polarized electron sources, this technique extends efficient polarized positron capabilities from GeV to MeV electron accelerators. …
Recent advances in electron and positron sources have resulted in new capabilities driven in most cases by the increasing demands of advanced accelerating systems. Electron sources for brighter beams and for high average-current beams are described. The status and remaining challenges for polarized electron beams are also discussed. For positron sources, recent activity in the development of polarized positron beams for future colliders is reviewed. Finally, a new proposal for combining laser cooling with beam polarization is presented.
Future electron-positron linear colliders require a highly polarized electron beam with a pulse structure that depends primarily on whether the acceleration utilizes warm or superconducting rf structures. The International Linear Collider (ILC) will use cold structures for the main linac. It is shown that a dc-biased polarized photoelectron source such as successfully used for the SLC can meet the charge requirements for the ILC micropulse with a polarization approaching 90%.
Various methods of obtaining longitudinally polarized positrons for future linear colliders are reviewed. Special attention is paid to the schemes using circularly polarized high-energy photons for positron production. Most effectively such photons are obtained from electrons passing through a helical undulator or colliding with a circularly polarized laser wave. Spectrum and polarization of radiation emitted during helical motion of electrons are considered in detail. A new simple presentation of known formulas is used to account for the influence of the wave intensity, of the electron-beam a…
The International Linear Collider (ILC) is a proposed electron-positron collider for the centre-of-mass energy range of 200 to 500 GeV and with upgrade options towards 1 TeV. The ILC would be the ideal tool to explore with high precision the properties of the new Higgs-like particle that has recently been discovered at the LHC with a mass of around 125 GeV. The ILC accelerator design is based on the mature superconducting technology that has been developed in the TESLA collaboration and that is currently being used for the European XFEL. The exploitation of the huge physics potential of the IL…
Polarized positron beams are in some respect mandatory complements to polarized electron beams. The advent of the PEPPo concept for polarized positron production opens the possibility for the developement at the Jefferson Laboratory of a continuous polarized positron beam. The benefits of such a beam for hadronic structure studies are discussed, together with the technical and technological challenges to face.
The future e-e+ 500 GeV International Linear Collider will rely on unprecedented nanometer scale particle beam size at the interaction point, in order to achieve the design luminosity. Tight tolerances on static and dynamic alignment of the accelerator cavities and optical components are demanded to transport and focus the high energy electron and positron beams with reasonable position jitter and low emittance. A brief review of techniques and devices evaluated and developed so far for the vibration diagnostics of the machine is presented in this paper.
The Polarized Electrons for Polarized Positrons experiment at the injector of the Continuous Electron Beam Accelerator Facility has demonstrated for the first time the efficient transfer of polarization from electrons to positrons produced by the polarized bremsstrahlung radiation induced by a polarized electron beam in a high-$Z$ target. Positron polarization up to 82\% have been measured for an initial electron beam momentum of 8.19~MeV/$c$, limited only by the electron beam polarization. This technique extends polarized positron capabilities from GeV to MeV electron beams, and opens access …
We evaluate the neutron and muon fluxes produced in the ILC beam dumps by Monte Carlo simulations and discuss their potential use in irradiation fields. We show that the beam dumps can provide high-intensity neutron and muon fluxes with spectra quite similar to secondary cosmic rays, which are suitable for soft error studies. The beam dumps deliver neutrons about $10^{11}$ times the secondary cosmic rays on spaces perpendicular to the beam axis and muons $10^8$ times downstream of the beam dumps in the initial phase of the ILC. Large-area irradiation of 1\,m$^2$ or more is possible. Difference…
A novel scheme is proposed for generating a polarized positron beam via multiphoton Breit-Wheeler process during the collision of a 10 GeV, pC seeding electron beam with the other 1 GeV, nC driving electron beam. The driving beam provides the strong self-generated field, and a suitable transverse deviation distance between two beams enables the field experienced by the seeding beam to be unipolar, which is crucial for realizing the positron polarization. We employ the particle simulation with a Monte-Carlo method to calculate the spin- and polarization-resolved photon emission and electron-pos…
Full exploitation of the physics potential of a future International Linear Collider will require the use of polarized electron and positron beams. Experiment E166 at the Stanford Linear Accelerator Center (SLAC) has demonstrated a scheme in which an electron beam passes through a helical undulator to generate photons (whose first-harmonic spectrum extended to 7.9MeV) with circular polarization, which are then converted in a thin target to generate longitudinally polarized positrons and electrons. The experiment was carried out with a one-meter-long, 400-period, pulsed helical undulator in the…
In a number of papers an attractive method of laser polarization of electrons (positrons) at storage rings or linear colliders has been proposed. We show that these suggestions are incorrect and based on errors in simulation of multiple Compton scattering and in calculation of the Compton spin-flip cross sections. We argue that the equilibrium polarization in this method is zero.
