Optomechanical coupling between a mechanical oscillator and light trapped in a cavity increases when the coupling takes place in a reduced volume. Here we demonstrate a GaAs semiconductor optomechanical disk system where both optical and mechanical energy can be confined in a sub-micron scale interaction volume. We observe giant optomechanical coupling rate up to 100 GHz/nm involving picogram mass mechanical modes with frequency between 100 MHz and 1 GHz. The mechanical modes are singled-out measuring their dispersion as a function of disk geometry. Their Brownian motion is optically resolved with a sensitivity of 10^(-17)m/sqrt(Hz) at room temperature and pressure, approaching the quantum limit imprecision.
We report on wavelength-sized GaAs optomechanical disk resonators showing ultra-strong optomechanical interaction. We observe optical transduction of a disk mechanical breathing mode with 1.4 GHz frequency and effective mass of ~ 2 pg. The measured vacuum optomechanical coupling rate reaches 0.8 MHz, with a related differential optomechanical coupling factor of 485 GHz/nm. The disk Brownian motion is optically resolved with a sensitivity of 10-17 m/{\sqrt}Hz at room temperature and pressure.
Optomechanical systems based on nanophotonics are advancing the field of precision motion measurement, quantum control and nanomechanical sensing. In this context III-V semiconductors offer original assets like the heteroepitaxial growth of optimized metamaterials for photon/phonon interactions. GaAs has already demonstrated high performances in optomechanics but suffers from two photon absorption (TPA) at the telecom wavelength, which can limit the cooperativity. Here, we investigate TPA-free III-V semiconductor materials for optomechanics applications: GaAs lattice-matched In0:5Ga0:5P and Al…
GaAs disk resonators (typical disk size 5 \mum * 200 nm in our work) are good candidates for boosting optomechanical coupling thanks to their ability to confine both optical and mechanical energy in a sub-micron interaction volume. We present results of optomechanical characterization of GaAs disks by near-field optical coupling from a tapered silica nano-waveguide. Whispering gallery modes with optical Q factor up to a few 10^5 are observed. Critical coupling, optical resonance doublet splitting and mode identification are discussed. We eventually show an optomechanical phenomenon of optical …
Chip-based cavity optomechanical systems are being considered for applications in sensing, metrology, and quantum information science. Critical to their development is an understanding of how the optical and mechanical modes interact, quantified by the coupling rate $g_{0}$. Here, we develop GaAs optomechanical resonators and investigate the moving dielectric boundary and photoelastic contributions to $g_{0}$. First, we consider coupling between the fundamental radial breathing mechanical mode and a 1550 nm band optical whispering gallery mode in microdisks. For decreasing disk radius from $R=…
We present a simple fabrication method for the realization of suspended GaAs nanomembranes for cavity quantum optomechanics experiments. GaAs nanomembranes with an area of 1.36 mm by 1.91 mm and a thickness of 160 nm are obtained by using a two-step selective wet-etching technique. The frequency noise spectrum reveals several mechanical modes in the kilohertz regime with mechanical Q-factors up to 2,300,000 at room temperature. The measured mechanical mode profiles agree well with a taut rectangular drumhead model. Our results show that GaAs nanomembranes provide a promising path towards quant…
We analyze the magnitude of the radiation pressure and electrostrictive stresses exerted by light confined inside GaAs semiconductor WGM optomechanical disk resonators, through analytical and numerical means, and find the electrostrictive force to be of prime importance. We investigate the geometric and photoelastic optomechanical coupling resulting respectively from the deformation of the disk boundary and from the strain-induced refractive index changes in the material, for various mechanical modes of the disks. Photoelastic optomechanical coupling is shown to be a predominant coupling mecha…
Recent experiments demonstrated that GaAs-AlAs based micropillar cavities are promising systems for quantum optomechanics, allowing the simultaneous three-dimensional confinement of near-infrared photons and acoustic phonons in the 18-100 GHz range. Here, we investigate through numerical simulations the optomechanical properties of this new platform. We evidence how the Poisson's ratio and semiconductor-vacuum boundary conditions lead to very distinct features in the mechanical and optical three dimensional confinement. We find a strong dependence of the mechanical quality factor and strain di…
We report on miniature GaAs disk optomechanical resonators vibrating in air in the radiofrequency range. The flexural modes of the disks are studied by scanning electron microscopy and optical interferometry, and correctly modeled with the elasticity theory for annular plates. The mechanical damping is systematically measured, and confronted with original analytical models for air damping. Formulas are derived that correctly reproduce both the mechanical modes and the damping behavior, and can serve as design tools for optomechanical applications in fluidic environment.
We present the design, fabrication and initial characterization of a paddle nanocavity consisting of a suspended sub-picogram nanomechanical resonator optomechanically coupled to a photonic crystal nanocavity. The optical and mechanical properties of the paddle nanocavity can be systematically designed and optimized, and key characteristics including mechanical frequency easily tailored. Measurements under ambient conditions of a silicon paddle nanocavity demonstrate an optical mode with quality factor $Q_o$ ~ 6000 near 1550 nm, and optomechanical coupling to several mechanical resonances with…
We demonstrate integrated optomechanical circuits with high mechanical quality factors prepared from nanocrystalline diamond thin films. Using chemomechanical polishing, the RMS surface roughness of as grown polycrystalline diamond films is reduced below 3nm to allow for the fabrication of high-quality nanophotonic circuits. By integrating free-standing nanomechanical resonators into integrated optical devices, efficient read-out of the thermomechanical motion of diamond resonators is achieved with on-chip Mach-Zehnder interferometers. Mechanical quality factors up to 28,800 are measured for f…
We report enhanced optomechanical coupling by embedding a nano-mechanical beam resonator within an optical race-track resonator. Precise control of the mechanical resonator is achieved by clamping the beam between two low-loss photonic crystal waveguide couplers. The low insertion loss and the rigid mechanical support provided by the couplers yield both high mechanical and optical Q-factors for improved signal quality.
Silicon on insulator photonics has offered a versatile platform for the recent development of integrated optomechanical circuits. However, there are some constraints such as the high cost of the wafers and limitation to a single physical device level. In the present work we investigate nanocrystalline silicon as an alternative material for optomechanical devices. In particular, we demonstrate that optomechanical crystal cavities fabricated of nanocrystalline silicon have optical and mechanical properties enabling non-linear dynamical behaviour and effects such as thermo-optic/free-carrier-disp…
Diamond integrated photonic devices are promising candidates for emerging applications in nanophotonics and quantum optics. Here we demonstrate active modulation of diamond nanophotonic circuits by exploiting mechanical degrees of freedom in free-standing diamond electro-optomechanical resonators. We obtain high quality factors up to 9600, allowing us to read out the driven nanomechanical response with integrated optical interferometers with high sensitivity. We are able to excite higher order mechanical modes up to 115 MHz and observe the nanomechanical response also under ambient conditions.
By harnessing the resonant nature of localized electromagnetic modes in a nanostructured silicon membrane, an all-dielectric metamaterial can act as nonlinear medium at optical telecommunications wavelengths. We show that such metamaterials provide extremely large optomechanical nonlinearities, operating at intensities of only a few μW per unit cell and modulation frequencies as high as 152 MHz, thereby offering a path to fast, compact and energy efficient all-optical metadevices.
We present the design of a femtogram L3-nanobeam photonic crystal cavity for optomechanical studies. Two symmetric nanobeams are created by placing three air slots in a silicon photonic crystal slab where three holes are removed. The optical quality factor (Q) is optimized up to 52,000. The nanobeams' mechanical frequencies are higher than 600 MHz due to their femtogram effective modal masses. The optical and mechanical modes are dispersively coupled with a vacuum optomechanical coupling rate g0/2pi exceeding 200 kHz. The anchor-loss-limited mechanical Q of the differential beam mode is evalua…
Collective phenomena emerging from non-linear interactions between multiple oscillators, such as synchronization and frequency locking, find applications in a wide variety of fields. Optomechanical resonators, which are intrinsically non-linear, combine the scientific assets of mechanical devices with the possibility of long distance controlled interactions enabled by travelling light. Here we demonstrate light-mediated frequency locking of three distant nano-optomechanical oscillators positioned in a cascaded configuration. The oscillators, integrated on a chip along a coupling waveguide, are…
It is shown that optomechanical forces can cause nonlinear self-channelling of light in a planar dual-slab waveguide. A system of two parallel silica nanowebs, spaced ~100 nm and supported inside a fibre capillary, is studied theoretically and an iterative scheme developed to analyse its nonlinear optomechanical properties. Steady-state field distributions and mechanical deformation profiles are obtained, demonstrating that self-channelling is possible in realistic structures at launched powers as low as a few mW. The differential optical nonlinearity of the self-channelled mode can be as much…
Light that carries linear or angular momentum can interact with a mechanical object giving rise to optomechanical effects. In particular, a photon transfers its intrinsic angular momentum to an object when the object either absorbs the photon or changes the photon polarization, as in an action/reaction force pair. Here, we present the implementation of light-induced selective resonant driving of the torsional mechanical modes of a single-mode tapered optical nanofiber. The nanofiber torsional mode spectrum is characterized by polarimetry, showing narrow natural resonances (Q$\approx$2,000). By…
Cavity optomechanical systems can be used for sensitive detection of mechanical motion and to control mechanical resonators, down to the quantum level. The strength with which optical and mechanical degrees of freedom interact is defined by the photon-phonon coupling rate $g_0$, which is especially large in nanoscale systems. Here, we demonstrate an optomechanical system based on a sliced photonic crystal nanobeam, that combines subwavelength optical confinement with a low-mass mechanical mode. Analyzing the transduction of motion and effects of radiation pressure we find a coupling rate $g_0$…
Flexible control of photons and phonons in silicon nanophotonic waveguides is a key feature for emerging applications in communications, sensing and quantum technologies. Strong phonon leakage towards the silica under-cladding hampers optomechanical interactions in silicon-on-insulator. This limitation has been circumvented by totally or partially removing the silica under-cladding to form pedestal or silicon membrane waveguides. Remarkable optomechanical interactions have been demonstrated in silicon using pedestal strips, membrane ribs, and photonic/phononic crystal membrane waveguides. Stil…
The combination of large per-photon optical force and small motional mass attainable in nanocavity optomechanical systems results in strong dynamical back-action between mechanical motion and the cavity light field. In this work we study the optical control of mechanical motion within two different nanocavity structures, a zipper nanobeam photonic crystal cavity and a double-microdisk whispering-gallery resonator. The strong optical gradient force within these cavities is shown to introduce signifcant optical rigidity into the structure, with the dressed mechanical states renormalized into opt…
Optomechanical crystals, purposely designed and fabricated semiconductor nanostructures, are used to enhance the coupling between the electromagnetic field and the mechanical vibrations of matter at the nanoscale. However, in real optomechanical crystals, imperfections open extra channels where the transfer of energy is lost, reducing the optomechanical coupling eficiency. Here, we quantify the role of disorder in a paradigmatic one-dimensional optomechanical crystal with full phononic and photonic bandgaps. We show how disorder can be exploited as a resource to enhance the optomechanical coup…
Non-invasive and ultra-accurate optical manipulation of nanometer objects has recently gained a growing interest as a powerful enabling tool in nanotechnology and biophysics. In this context, Self-Induced Back-Action (SIBA) trapping in nano-optical cavities has shown a unique potential for trapping and manipulating nanometer-sized objects under low optical intensities. Yet, the existence of the SIBA effect has that far only been evidenced indirectly through its enhanced trapping performances. In this article we present for the first time a direct experimental evidence of the self-reconfigurati…
We describe the design, fabrication, and characterization of a one-dimensional silicon photonic crystal cavity in which a central slot is used to enhance the overlap between highly localized optical and mechanical modes. The optical mode has an extremely small mode volume of 0.017 $(λ_{vac}/n)^3$, and an optomechanical vacuum coupling rate of 310 kHz is measured. With optical quality factors up to $1.2 \cdot 10^5$, fabricated devices are in the resolved-sideband regime. The electric field has its maximum at the slot wall and couples to the in-plane breathing motion of the slot. The optomechani…
We report on an integrated GaAs disk/waveguide system. A millimeter-long waveguide is suspended and tapered on the chip over a length of 25 μm to evanescently couple to high Q optical whispering gallery modes of a GaAs disk. The critical coupling regime is obtained both by varying the disk/guide gap distance and the width of the suspended nanoscale taper. The experimental results are in good agreement with predictions from the coupled mode theory.
We fabricated an acousto-optic semiconductor hybrid device for strong optomechanical coupling of individual quantum emitters and a surface acoustic wave. Our device comprises a surface acoustic wave chip made from highly piezoelectric LiNbO$_3$ and a GaAs-based semiconductor membrane with an embedded layer of quantum dots. Employing multi-harmonic transducers, we generated sound waves on LiNbO$_3$ over a wide range of radio frequencies. We monitored their coupling to and propagation across the semiconductor membrane both in the electrical and optical domain. We demonstrate enhanced optomechani…
Cavity optomechanical systems are being widely developed for precision force and displacement measurements. For nanomechanical transducers, there is usually a trade-off between the frequency ($f_{M}$) and quality factor ($Q_{M}$), which limits temporal resolution and sensitivity. Here, we present a monolithic cavity optomechanical transducer supporting both high $f_{M}$ and high $Q_{M}$. By replacing the common doubly-clamped, Si$_3$N$_4$ nanobeam with a tuning fork geometry, we demonstrate devices with the fundamental $f_{M}\approx29$ MHz and $Q_{M}\approx2.2$$\times10^5$, corresponding to an…
Diamond offers unique material advantages for the realization of micro- and nanomechanical resonators due to its high Young's modulus, compatibility with harsh environments and superior thermal properties. At the same time, the wide electronic bandgap of 5.45eV makes diamond a suitable material for integrated optics because of broadband transparency and the absence of free-carrier absorption commonly encountered in silicon photonics. Here we take advantage of both to engineer full-scale optomechanical circuits in diamond thin films. We show that polycrystalline diamond films fabricated by chem…
The effectiveness of self-mixing interferometry has been demonstrated across the electromagnetic spectrum, from visible to microwave frequencies, in a plethora of sensing applications, ranging from distance measurement to material analysis, microscopy and coherent imaging. Owing to their intrinsic stability to optical feedback, quantum cascade lasers (QCLs) represent a source that offers unique and versatile characteristics to further improve the self-mixing functionality at mid infrared and terahertz (THz) frequencies. Here, we show the feasibility of detecting with nanometer precision deeply…
We present a design methodology and analysis of a cavity optomechanical system in which a localized GHz frequency mechanical mode of a nanobeam resonator is evanescently coupled to a high quality factor (Q>10^6) optical mode of a separate nanobeam optical cavity. Using separate nanobeams provides flexibility, enabling the independent design and optimization of the optics and mechanics of the system. In addition, the small gap (approx. 25 nm) between the two resonators gives rise to a slot mode effect that enables a large zero-point optomechanical coupling strength to be achieved, with g/2pi > …
Tunable evanescent coupling is used to modify the optomechanical interactions within a split-beam photonic crystal nanocavity. An optical fiber taper probe is used to renormalize the optical nanocavity field and introduce a dissipative optomechanical coupling channel, reconfiguring and enhancing coupling between the optical and mechanical resonances of the device. Positioning of the fiber taper allows preferential coupling to specific mechanical modes and provides a mechanism for tuning the optomechanical interaction between dissipative and dispersive coupling regimes.
We experimentally and theoretically investigate mechanical nanooscillators coupled to the light in an optical ring resonator made of dielectric mirrors. We identify an optomechanical damping mechanism that is fundamentally different to the well known cooling in standing wave cavities. While, in a standing wave cavity the mechanical oscillation shifts the resonance frequency of the cavity in a ring resonator the frequency does not change. Instead the position of the nodes is shifted with the mechanical excursion. We derive the damping rates and test the results experimentally with a silicon-nit…
We demonstrate the design, fabrication and characterization of nanobeam photonic crystal cavities in (111)-GaAs with multiple high quality factor modes, with large frequency separations (up to 740 nm in experiment, i.e., a factor of 1.5 and up to an octave in theory). Such structures are crucial for efficient implementation of nonlinear frequency conversion. Here, we employ them to demonstrate sum frequency generation from 1300 nm and 1950 nm to 780 nm. These wavelengths are particularly interesting for quantum frequency conversion between Si vacancy centers in diamond and the fiber optic netw…
Design of a doubly-clamped beam structure capable of localizing mechanical and optical energy at the nanoscale is presented. The optical design is based upon photonic crystal concepts in which patterning of a nanoscale-cross-section beam can result in strong optical localization to an effective optical mode volume of 0.2 cubic wavelengths ((λ_{c})^3). By placing two identical nanobeams within the near field of each other, strong optomechanical coupling can be realized for differential motion between the beams. Current designs for thin film silicon nitride beams at a wavelength of 1.5 microns i…
Laser cooling of mechanical degrees of freedom is one of the most significant achievements in the field of opto-mechanics. Here, we report, for the first time to the best of our knowledge, efficient passive optomechanical cooling of the motion of a freestanding waveguide coupled to a whispering-gallery-mode (WGM) resonator. The waveguide is an 8 mm long glass-fiber nanospike, which has a fundamental flexural resonance at Ω/2π = 2.5 kHz and a Q-factor of 1.2 10**5. Upon launching 250 μW laser power at an optical frequency close to the WGM resonant frequency, we observed cooling of the nanospike…
We experimentally demonstrate the controlled enhancement of the mechanical quality factor Q of GaAs disk optomechanical resonators. Disks vibrating at 1.3 GHz with a mechanical shield integrated in their pedestal show a Q improvement by a factor 10 to 16. The structure is modeled numerically and different modes of vibration are observed, which shed light on the Q enhancement mechanism. An optimized double-disk geometry is presented that promises Q above the million for a large parameter range.
We demonstrate the optomechanical cooling of a tapered optical nanofiber by coupling the polarization of light to the mechanical angular momentum of the system. The coupling is enabled by birefringence in the fiber and does not make use of an optical resonator. We find evidence for cooling in the distribution of thermally driven amplitude fluctuations and the noise spectrum of the torsional modes. Our proof-of-principle demonstration shows cavity-less cooling of the torsional degree of freedom of a macroscopically extended nanofiber.
Vibrational resonance amplifies a weak low-frequency signal by use of an additional non-resonant high-frequency modulation. The realization of weak signal enhancement in integrated nonlinear optical nanocavities is of great interest for nanophotonic applications where optical signals may be of low power. Here, we report experimental observation of vibrational resonance in a thermo-optically bistable photonic crystal optomechanical resonator with an amplification up to +16 dB. The characterization of the bistability can interestingly be done using a mechanical resonance of the membrane, which i…
Nanoscale photonic crystal cavity optomechanical devices enable detection of nanomechanical phenomena with a sensitivity sufficient to observe quantum effects. Here we present the design of a one-dimensional air-mode photonic crystal cavity patterned in a silicon nitride nanobeam, and show that it forms the basis for cavity optomechanical split-beam and paddle nanocavity devices useful for force detection and nonlinear quantum sensing. The air-mode of this device is advantageous for optomechanical coupling, while also having ultrahigh optical quality factor $Q_o\sim 10^6$ despite its proximity…
Optical measurements of a nanoscale silicon optomechanical crystal cavity with a mechanical resonance frequency of 3.6GHz are performed at sub-kelvin temperatures. We infer optical-absorption-induced heating and damping of the mechanical resonator from measurements of phonon occupancy and motional sideband asymmetry. At the lowest probe power and lowest fridge temperature (10mK), the localized mechanical resonance is found to couple at a rate of 400Hz (Q=9x10^6) to a thermal bath of temperature 270mK. These measurements indicate that silicon optomechanical crystals cooled to millikelvin temper…
Piezoelectric optomechanical platforms represent one of the most promising routes towards achieving quantum transduction of photons between the microwave and optical frequency domains. However, there are significant challenges to achieving near-unity transduction efficiency. We discuss such factors in the context of the two main approaches being pursued for high efficiency transduction. The first approach uses one-dimensional nanobeam optomechanical crystals excited by interdigitated transducers, and is characterized by large single-photon optomechanical coupling strength, limited intracavity …
Nonlinear optomechanical coupling is the basis for many potential future experiments in quantum optomechanics (e.g., quantum non-demolition measurements, preparation of non-classical states), which to date have been difficult to realize due to small non-linearity in typical optomechanical devices. Here we introduce an optomechanical system combining strong nonlinear optomechanical coupling, low mass and large optical mode spacing. This nanoscale "paddle nanocavity" supports mechanical resonances with hundreds of fg mass which couple nonlinearly to optical modes with a quadratic optomechanical …
Optically measuring in the photon counting regime is a recurrent challenge in modern physics and a guarantee to develop weakly invasive probes. Here we investigate this idea on a hybrid nano-optomechanical system composed of a nanowire hybridized to a single Nitrogen-Vacancy (NV) defect. The vibrations of the nanoresonator grant a spatial degree of freedom to the quantum emitter and the photon emission event can now vary in space and time. We investigate how the nanomotion is encoded on the detected photon statistics and explore their spatio-temporal correlation properties. This allows a quant…
A III-V compound semiconductor nanowire is an attractive material for a novel hybrid quantum interface that interconnects photons, electrons, and phonons through a wavelength-tunable quantum structure embedded in its free-standing structure. In such a nanomechanical element, however, a challenge is how to detect and manipulate a small number of phonons via its tiny mechanical motion. A solution would be to couple an optical cavity to a nanowire by introducing the ``cavity optomechanics'' framework, but the typical size difference between them becomes a barrier to achieving this. Here, we demon…
We develop a systematic method for deriving a quantum optical multi-mode Hamiltonian for the interaction of photons and phonons in nanophotonic dielectric materials by applying perturbation theory to the electromagnetic Hamiltonian. The Hamiltonian covers radiation pressure and electrostrictive interactions on equal footing. As a paradigmatic example, we apply our method to a cylindrical nanoscale waveguide, and derive a Hamiltonian description of Brillouin quantum optomechanics. We show analytically that in nanoscale waveguides radiation pressure dominates over electrostriction, in agreement …
A hybrid device comprising a (Al)GaAs quantum dot heterostructure and a LiNbO$_3$ surface acoustic wave resonator is fabricated by heterointegration. High acoustic quality factors $Q>4000$ are demonstrated for an operation frequency $f\approx 300$ MHz. The measured large quality factor-frequency products $Q\times f>10^{12}$ ensures the suppression of decoherence due to thermal noise for temperatures exceeding $T>50\,\mathrm{K}$. Frequency and position dependent optomechanical coupling of single quantum dots and the resonator modes is observed.
A significant challenge in the development of chip-scale cavity-optomechanical devices as testbeds for quantum experiments and classical metrology lies in the coupling of light from nanoscale optical mode volumes to conventional optical components such as lenses and fibers. In this work we demonstrate a high-efficiency, single-sided fiber-optic coupling platform for optomechanical cavities. By utilizing an adiabatic waveguide taper to transform a single optical mode between a photonic crystal zipper cavity and a permanently mounted fiber, we achieve a collection efficiency for intracavity phot…
In the majority of optomechanical experiments, the interaction between light and mechanical motion is mediated by radiation pressure, which arises from momentum transfer of reflecting photons. This is an inherently weak interaction, and optically generated carriers in semiconductors have been predicted to be the mediator of different and potentially much stronger forces. Here we demonstrate optomechanical forces induced by electron-hole pairs in coupled quantum wells embedded into a free-free nanomembrane. We identify contributions from the deformation-potential and piezoelectric coupling and …
The interaction of optical and mechanical modes in nanoscale optomechanical systems has been widely studied for applications ranging from sensing to quantum information science. Here, we develop a platform for cavity optomechanical circuits in which localized and interacting 1550 nm photons and 2.4 GHz phonons are combined with photonic and phononic waveguides. Working in GaAs facilitates manipulation of the localized mechanical mode either with a radio frequency field through the piezo-electric effect, or optically through the strong photoelastic effect. We use this to demonstrate a novel aco…
In the field of cavity nano-optomechanics, the nanoresonator-in-the-middle approach consists in inserting a sub-wavelength sized deformable resonator, here a nanowire, in the small mode volume of a fiber microcavity. Internal resonances in the nanowire enhance the light nanowire interaction which provide giant coupling strengthes -- sufficient to enter the single photon regime of cavity optomechanics -- at the condition to precisely position the nanowire within the cavity field. Here we expose a theoretical description that combines an analytical formulation of the Mie-scattering of the intrac…
We present the design of an optomechanical crystal nanobeam cavity that combines finite-element simulation with numerical optimization, and considers the optomechanical coupling arising from both moving dielectric boundaries and the photo-elastic effect. Applying this methodology results in a nanobeam with an experimentally realized intrinsic optical Q-factor of 1.2x10^6, a mechanical frequency of 5.1GHz, a mechanical Q-factor of 6.8x10^5 (at T=10K), and a zero-point-motion optomechanical coupling rate of g=1.1MHz.
Diamond provides superior optical and mechanical material properties, making it a prime candidate for the realization of integrated optomechanical circuits. Because diamond sub- strates have matured in size, efficient nanostructuring methods can be used to realize full-scale integrated devices. Here we review optical and mechanical resonators fab- ricated from polycrystalline as well as single crystalline diamond. We present relevant material properties with respect to implementing optomechanical devices and compare them with other material systems. We give an overview of diamond integrated op…
Optomechanical devices sensitively transduce and actuate motion of nanomechanical structures using light. Single--crystal diamond promises to improve the performance of optomechanical devices, while also providing opportunities to interface nanomechanics with diamond color center spins and related quantum technologies. Here we demonstrate dissipative waveguide--optomechanical coupling exceeding 35 GHz/nm to diamond nanobeams supporting both optical waveguide modes and mechanical resonances, and use this optomechanical coupling to measure nanobeam displacement with a sensitivity of $9.5$ fm/$\s…
