我们实现了一个腔光机电系统集成电驱动能力的纳米机电设备与超灵敏的机械转导实现通过腔内光机械耦合。实现了高达0.40 microN的电梯度力，同时机械转换灵敏度为1.5 X 10^-18 m/rtHz，比迄今为止的任何纳米机电系统都提高了三个数量级。展示了光机电反馈冷却，表现出强烈的挤压的环内转导信号。即使在测量反作用引起光机械相关的临界范例中，环外换能也提供准确的温度校准。
英文摘要：
We implement a cavity opto-electromechanical system integrating electrical actuation capabilities of nanoelectromechanical devices with ultrasensitive mechanical transduction achieved via intra-cavity optomechanical coupling. Electrical gradient forces as large as 0.40 microN are realized, with simultaneous mechanical transduction sensitivity of 1.5 X 10^-18 m/rtHz representing a three orders of magnitude improvement over any nanoelectromechanical system to date. Opto-electromechanical feedback cooling is demonstrated, exhibiting strong squashing of the in-loop transduction signal. Out-of-loop transduction provides accurate temperature calibration even in the critical paradigm where measurement backaction induces opto-mechanical correlations.
We demonstrate squeezing of a strongly interacting opto-electromechanical system using a parametric drive. By employing real-time feedback on the phase of the pump at twice the resonance frequency the thermo-mechanical noise is squeezed beyond the 3 dB instability limit. Surprisingly, this method can also be used to generate highly nonlinear states. We show that using the parametric drive with feedback on, classical number-like and cat-like states can be prepared. This presents a valuable electro-optomechanical state-preparation protocol that is extendable to the quantum regime.
The control of slow and fast light propagation, in the probe transmission in a single experiment, is a challenging task. This type of control can only be achieved through highly nonlinear interactions and additional interfering pathway(s), which is therefore seldom reported. Here, we devise a scheme in which slow light, and a tunable switch from slow light to fast light can be achieved in the probe transmission based on a hybrid setup, which is composed of an optical cavity with two charged nano mechanical resonators (MRs). The two MRs are electrostatically coupled via tunable Coulomb coupling…
We present a scheme for ground-state cooling of a mechanical resonator by simultaneously coupling it to a superconducting qubit and a cavity field. The Hamiltonian describing the hybrid system dynamics is systematically derived. The cooling process is driven by a red-detuned ac drive on the qubit and a laser drive on the optomechanical cavity. We have investigated cooling in the weak and the strong coupling regimes for both the individual system, i.e., qubit assisted cooling and optomechanical cooling, and compared them with the effective hybrid cooling. It is shown that hybrid cooling is more…
The fields of opto- and electromechanics have facilitated numerous advances in the areas of precision measurement and sensing, ultimately driving the studies of mechanical systems into the quantum regime. To date, however, the quantization of the mechanical motion and the associated quantum jumps between phonon states remains elusive. For optomechanical systems, the coupling to the environment was shown to preclude the detection of the mechanical mode occupation, unless strong single photon optomechanical coupling is achieved. Here, we propose and analyse an electromechanical setup, which allo…
Laser cooling of mesoscopic mechanical resonators is of great interest for both fundamental studies and practical applications. We provide a general framework to describe the cavity-assisted backaction cooling in the strong coupling regime. By studying the cooling dynamics, we find that the temporal evolution of mean phonon number oscillates as a function of the optomechanical coupling strength depending on frequency mixing. The further analytical result reveals that the optimal cooling limit is obtained when the system eigenmodes satisfy the frequency matching condition. The reduced instantan…
Cavity electromechanics relies on parametric coupling between microwave and mechanical modes to manipulate the mechanical quantum state, and provide a coherent interface between different parts of hybrid quantum systems. High coherence of the mechanical mode is of key importance in such applications, in order to protect the quantum states it hosts from thermal decoherence. Here, we introduce an electromechanical system based around a soft-clamped mechanical resonator with an extremely high Q-factor (>$10^9$) held at very low (30 mK) temperatures. This ultracoherent mechanical resonator is capa…
We present a complete theory for laser cooling of a macroscopic radio-frequency LC electrical circuit by means of an optoelectromechanical system, consisting of an optical cavity dispersively coupled to a nanomechanical oscillator, which is in turn capacitively coupled to the LC circuit of interest. We determine the optimal parameter regime where the LC resonator can be cooled down to its quantum ground state, which requires a large optomechanical cooperativity, and a larger electromechanical cooperativity. Moreover, comparable optomechanical and electromechanical coupling rates are preferable…
Quantum manipulation of macroscopic mechanical systems is of great interest in both fundamental physics and applications ranging from high-precision metrology to quantum information processing. A crucial goal is to cool the mechanical system to its quantum ground state. In this review, we focus on the cavity optomechanical cooling, which exploits the cavity enhanced interaction between optical field and mechanical motion to reduce the thermal noise. Recent remarkable theoretical and experimental efforts in this field have taken a major step forward in preparing the motional quantum ground stat…
We consider feedback cooling in a cavityless levitated optomechanics setup, and we investigate the possibility to improve the feedback implementation. We apply optimal control theory to derive the optimal feedback signal both for quadratic (parametric) and linear (electric) feedback. We numerically compare optimal feedback against the typical feedback implementation used for experiments. In order to do so, we implement a tracking scheme that takes into account the modulation of the laser intensity. We show that such a tracking implementation allows us to increase the feedback strength, leading…
We propose and analyse a quantum electromechanical system composed of a monolithic quartz bulk acoustic wave (BAW) oscillator coupled to a superconducting transmon qubit via an intermediate LC electrical circuit. Monolithic quartz oscillators offer unprecedentedly high effective masses and quality factors for the investigation of mechanical oscillators in the quantum regime. Ground-state cooling of such mechanical modes via resonant piezoelectric coupling to an LC circuit, which is itself sideband cooled via coupling to a transmon qubit, is shown to be feasible. The fluorescence spectrum of th…
Measurement-based control has emerged as an important technique to prepare mechanical resonators in pure quantum states for applications in quantum information processing and quantum sensing. Conventionally this has required two separate channels, one for probing the motion and another one acting back on the resonator. In this work, we analyze and experimentally demonstrate a technique of single-laser feedback cooling, where one laser is used for both probing and controlling the mechanical motion. We show using an analytical model and experiments that feedback cooling is feasible in this mode …
Ground state cooling of massive mechanical objects remains a difficult task restricted by the unresolved mechanical sidebands. We propose an optomechanically-induced-transparency cooling scheme to achieve ground state cooling of mechanical motion without the resolved sideband condition in a pure optomechanical system with two mechanical modes coupled to the same optical cavity mode. We show that ground state cooling is achievable for sideband resolution $ω_{m}/κ$ as low as 0.003. This provides a new route for quantum manipulation of massive macroscopic devices and high-precision measurements.
Standard optomechanical cooling methods ideally require weak coupling and cavity damping rates which enable the motional sidebands to be well resolved. If the coupling is too large then sideband-resolved cooling is unstable or the rotating wave approximation can become invalid. In this work we describe a protocol to cool a mechanical resonator coupled to a driven optical mode in an optomechanical cavity, which is also coupled to an optical mode in another auxiliary optical cavity, and both the cavities are frequency-modulated. We show that by modulating the amplitude of the drive as well, one …
In cavity optomechanics, light is used to control mechanical motion. A central goal of the field is achieving single-photon strong coupling, which would enable the creation of quantum superposition states of motion. Reaching this limit requires significant improvements in optomechanical coupling and cavity coherence. Here we introduce an optomechanical architecture consisting of a silicon nitride membrane coupled to a three-dimensional superconducting microwave cavity. Exploiting their large quality factors, we achieve an optomechanical cooperativity of 146,000 and perform sideband cooling of …
Optomechanical coupling between a light field and the motion of a cavity mirror via radiation pressure plays an important role for the exploration of macroscopic quantum physics and for the detection of gravitational waves (GWs). It has been used to cool mechanical oscillators into their quantum ground states and has been considered to boost the sensitivity of GW detectors, e.g. via the optical spring effect. Here, we present the experimental characterization of generalized, that is, dispersive and dissipative optomechanical coupling, with a macroscopic (1.5mm)^2-sized silicon nitride (SiN) me…
We theoretically study the laser cooling of cavity optomechanics when the mechanical resonance frequency and damping depend on time. In the regime of weak optomechanical coupling we extend the theory of laser cooling using an adiabatic approximation. We discuss the modifications of the cooling dynamics and compare it with numerical simulations in a wide range of modulation frequencies.
Ground state cooling of micromechanical oscillator is a paradigmatic goal for observing quantum mechanical effects in cavity optomechanics. We study theoretically the ground state cooling of a mechanical oscillator in an optomechanical cavity in presence of a quantum well placed inside the cavity. Due to mode tailoring in presence of the quantum well, the cavity response gets modified and leads to asymmetric heating and cooling processes. This facilitates the cooling of the mechanical oscillator even in the unresolved-sideband regime, via inhibition of Stokes scattering.
We analyze the performance of optomechanical cooling of a mechanical resonator in the presence of a degenerate optical parametric amplifier within the optomechanical cavity, which squeezes the cavity light. We demonstrate that this allows to significantly enhance the cooling efficiency via the coherent suppression of Stokes scattering. The enhanced cooling occurs also far from the resolved sideband regime, and we show that this cooling scheme can be more efficient than schemes realized by injecting a squeezed field into the optomechanical cavity.
We investigate theoretically the effect of optical feedback from a cavity containing an ultracold two level atomic ensemble, on the bistable behavior shown by mean intracavity optical field and the ground state cooling effect of the mechanical oscillator in an optomechanical cavity resonator. The optical bistability can be controlled by tuning the frequency and power of the single driving laser as well as by varying the atom-cavity coupling strength in the atomic cavity. Study of the cooling of the mechanical oscillator, in both good and bad cavity limits, reveals that the hybrid system is mor…
Coupled electromechanical resonators that can be independently driven/detected and easily integrated with external circuits are essential for exploring mechanical modes based signal processing. Here, we present a room temperature phonon-cavity electromechanical system, consisting of two distinct resonators: a silicon nitride electromechanical drum capacitively coupled to an aluminum one. We demonstrate electromechanically induced transparency and amplification in a two-tone driving scheme and observe the phonon-cavity force affecting the mechanical damping rates of both movable objects. We als…
The field of cavity optomechanics has achieved groundbreaking photonic control and detection of mechanical oscillators, based on their coupling to linear electromagnetic modes. Lately, however, there is an uprising interest in exploring cavity nonlinearities as a powerful new resource in radiation-pressure interacting systems. Here, we present a flux-mediated optomechanical device combining a nonlinear Josephson-based superconducting quantum interference cavity with a mechanical nanobeam. We demonstrate how the intrinsic Kerr nonlinearity of the microwave circuit can be used for a counter-intu…
Nano-electromechanical systems implement the opto-mechanical interaction combining electromagnetic circuits and mechanical elements. We investigate an inductively coupled nano-electromechanical system, where a superconducting quantum interference device (SQUID) realizes the coupling. We show that the resonance frequency of the mechanically compliant string embedded into the SQUID loop can be controlled in two different ways: (i) the bias magnetic flux applied perpendicular to the SQUID loop, (ii) the magnitude of the in-plane bias magnetic field contributing to the nano-electromechanical coupl…
Degenerate optomechanical parametric oscillators are optical resonators in which a mechanical degree of freedom is coupled to a cavity mode that is nonlinearly amplified via parametric down-conversion of an external pumping laser. Below a critical pumping power the down-converted field is purely quantum-mechanical, making the theoretical description of such systems very challenging. Here we introduce a theoretical approach that is capable of describing this regime, even at the critical point itself. We find that the down-converted field can induce significant mechanical cooling and identify th…
We investigate theoretically the effect of optical feedback from a cavity containing an ultracold two level atomic ensemble, on the bistable behavior shown by mean intracavity optical field in an optomechanical cavity resonator. It turns out that the optical bistability can be controlled by tuning the frequency and power of the driving laser and is largely affected by the presence of the atomic ensemble in the feedback cavity. In essence, our work emphasizes the possibility of realization of a controllable optical switch depending on the hybrid interaction, commanding lower threshold power tha…
Quantum ground-state cooling of macroscopic mechanical resonators is of essential importance to both fundamental physics and applied science. Conventional method of laser cooling is limited by the quantum backaction, which requires mechanical sideband resolved in order to cool to ground state. This work presents an idea to break the quantum backaction limit by engineering intracavity optical squeezing. It gives rise to quantum interference for all the dissipation channels, and under certain circumstances can totally remove the influence of the cavity dissipation and the resultant quantum backa…
We propose a scheme in which the cooling of a mechanical resonator is achieved by exposing the optomechanical system to a non-Markovian environment. Because of the backflow from the non-Markovian environment, the phonon number can go beyond the conventional cooling limit in a Markovian environment. Utilizing the spectrum density obtained in the recent experiment [Nature Communications 6, 7606 (2015)], we show that the cooling process is highly effective in a non-Markovian environment. The analysis of the cooling mechanism in a non-Markovian environment reveals that the non-Markovian memory eff…
Optomechanical cooling is a prerequisite for many exotic applications promised by modern quantum technology and it is crucial to achieve it in short times, in order to minimize the undesirable effects of the environment. We formulate cavity optomechanical cooling as a minimum-time optimal control problem on anti-de Sitter space of appropriate dimension and use the Legendre pseudospectral optimization method to find the minimum time and the corresponding optimal control, for various values of the maximum coupling rate between the cavity field and the mechanical resonator. The present framework …
Ground-state cooling of mechanical resonators is an important task in quantum optomechanics, because it is a necessary prerequisite for creation, manipulation, and application of macroscopic mechanical coherence. Here, we propose a transient-state scheme to accelerate ground-state cooling of a mechanical resonator in a three-mode loop-coupled optomechanical system via shortcuts to adiabaticity (STA). We consider four kinds of coupling protocols and calculate the evolution of the mean phonon number of the mechanical resonator in both the adiabatic and STA cases. We verify that the ground-state …
We propose a quantum interference cooling scheme for a nano-mechanical resonator (NAMR) in a hybrid optomechanical system, where the atoms are trapped in an optomechanical cavity, coupling to an additional optical cavity. The absorption of the optomechanical resonator can be modified by quantum interference effects induced by the atom-cavity and cavity-cavity couplings independently. With the employment of the quantum interference, the desired transition for cooling is enhanced, along with the heating suppression due to the undesired transition. As a result, the NAMR vibration can be cooled do…
In this paper, we study theoretically a hybrid optomechanical system consisting of a degenerate optical parametric amplifier inside a driven optical cavity with a moving end mirror which is modeled as a stiffening Duffing-like anharmonic quantum mechanical oscillator. By providing analytical expressions for the critical values of the system parameters corresponding to the emergence of the multistability behavior in the steady-state response of the system, we show that the stiffening mechanical Duffing anharmonicity reduces the width of the multistability region while the optical parametric non…
We present a theoretical scheme for ground state cooling of a mechanical resonator in a membrane-in-middle optomechanical system (OMS) driven by two red-detuned drive fields. The details of dynamical evolution of OMS are provided, and the effect of system conditions on cooling results are systematically studied. Most importantly, the setups with two drives are found to be capable of achieving better cooling results than the theoretical cooling limit with single cavity. Even an improvement by one order of thermal phonon number is possible with proper combination of the cavity damping rate and d…
Optical measurement of the motion of a 940 kHz mechanical resonance of a silicon nitride nanostring resonator is demonstrated with a read out noise imprecision reaching 37 dB below that of the resonator's zero-point fluctuations. Via intensity modulation of the optical probe laser, radiation pressure feedback is used to cool and damp the mechanical mode from an initial room temperature occupancy of $\bar{n}_{b} = 6.5 \times 10^6$ ($T_{b}=295$K) down to a phonon occupation of $\langle n \rangle = 66 \pm 10$, representing a mode temperature of $T_{m} \approx 3$mK. The five decades of cooling is …
Under a strong quantum measurement, the motion of an oscillator is disturbed by the measurement back-action, as required by the Heisenberg uncertainty principle. When a mechanical oscillator is continuously monitored via an electromagnetic cavity, as in a cavity optomechanical measurement, the back-action is manifest by the shot noise of incoming photons that becomes imprinted onto the motion of the oscillator. Following the photons leaving the cavity, the correlations appear as squeezing of quantum noise in the emitted field. Here we observe such "ponderomotive" squeezing in the microwave dom…
