Pentacenequinone (PnQ) impurities have been introduced into a pentacene source material at number densities from 0.001 to 0.474 to quantify the relative effects of impurity content and grain boundary structure on transport in pentacene thin-film transistors. Atomic force microscopy (AFM) and electrical measurements of top-contact pentacene thin-film transistors have been employed to directly correlate initial structure and final film structures, with the device mobility as a function of added impurity content. The results reveal a factor four decrease in mobility without significant changes in film morphology for source PnQ number fractions below ~0.008. For these low concentrations, the impurity thus directly influences transport, either as homogeneously distributed defects or by concentration at the otherwise-unchanged grain boundaries. For larger impurity concentrations, the continuing strong decrease in mobility is correlated with decreasing grain size, indicating an impurity-induced increase in the nucleation of grains during early stages of film growth.
We demonstrate an organic memory-transistor device based on a pentacene-gold nanoparticles active layer. Gold (Au) nanoparticles are immobilized on the gate dielectric (silicon dioxide) of a pentacene transistor by an amino-terminated self-assembled monolayer. Under the application of writing and erasing pulses on the gate, large threshold voltage shift (22 V) and on/off drain current ratio of ~3E4 are obtained. The hole field-effect mobility of the transistor is similar in the on and off states (less than a factor 2). Charge retention times up to 4500 s are observed. The memory effect is main…
Gate bias stress instability in organic field-effect transistors (OFETs) is a major conceptual and device issue. This effect manifests itself by an undesirable shift of the transfer characteristics and is associated with long term charge trapping. We study the role of the dielectric and the semiconductor separately by producing OFETs with the same semiconductor (pentacene) combined with different dielectrics (SiO$_2$ and Cytop). We show, it is possible to fabricate devices which are immune to gate bias stress. For other material combinations, charge trapping occurs in the semiconductor alone, …
Pentacenequinone (PnQ) impurities have been introduced into a pentacene source material in a controlled manner to quantify the relative effects of the impurity content on grain boundary structure and thin film nucleation. Atomic force microscopy (AFM) has been employed to directly characterize films grown using 0.0-7.5% PnQ by weight in the source material. Analysis of the distribution of capture zones areas of submonolayer islands as a function of impurity content shows that for large PnQ content the critical nucleus size for forming a Pn island is smaller than for low PnQ content. This resul…
We studied the influence of oxygen on the electronic trap states in a pentacene thin film. This was done by carrying out gated four-terminal measurements on thin-film transistors as a function of temperature and without ever exposing the samples to ambient air. Photooxidation of pentacene is shown to lead to a peak of trap states centered at 0.28 eV from the mobility edge, with trap densities of the order of 10(18) cm(-3). These trap states need to be occupied at first and cause a reduction in the number of free carriers, i.e. a consistent shift of the density of free holes as a function of ga…
We present the first thermoelectric measurements on pentacene field effect transistors. We report high values of the Seebeck coefficient at room temperature between 240 and 500 micro V/K depending on the dielectric surface treatment. These values are independent of the thickness of the channel and of the applied gate voltage. Two contributions to the Seebeck coefficient are clearly identified: the expected contribution that is dependent on the position of the transport level and reflects the activated character of carrier generation, and an unexpected intrinsic contribution of 265 plus minus 4…
Funtionalized pentacene, 6,13-bis(triisopropylsilylethynyl)pentacene (TIPS-pentacene), field-effect transistors(FET's) were made by thermal evaporation or solution deposition method and the mobility was measured as a function of temperature and light power. The field-effect mobility ($μ$$_{\rm FET}$) has a gate-voltage dependent activation energy. A non-monotonic temperature dependence was observed at high gate voltage (V$_G$ $<$ -30 V) with activation energy E$_a$ $\sim$ 60 - 170 meV,depending on the fabrication procedure. The gate-voltage dependent mobility and non-monotonic temperature depe…
We report on a healing of defects at room temperature in the organic semiconductor pentacene. This peculiar effect is a direct consequence of the weak intermolecular interaction which is characteristic of organic semiconductors. Pentacene thin-film transistors were fabricated and characterized by in situ gated four-terminal measurements. Under high vacuum conditions (base pressure of order 10E-8 mbar), the device performance is found to improve with time. The effective field-effect mobility increases by as much as a factor of two and mobilities up to 0.45 cm2/Vs were achieved. In addition, the…
In recent years, thin-film organic field-effect transistors (OFETs) have begun to be considered as a possible alternative to the hydrogenated amorphous silicon thin-film transistors (a-Si:H TFT's) used in active matrix flat panel displays and other large-area electronics applications. Low-temperature processability, low-cost fabrication and compatibility with arbitrary substrates are some of the promising advantages of OFETs, among others. Of the many organic materials available, pentacene, in particular, is one of the leading candidates for use in current thin-film OFET architectures - this b…
We report on the generation of a discrete trap state during negative gate bias stress in pentacene single crystal "flip-crystal" field-effect transistors with a SiO2 gate dielectric. Trap densities of up to 2*10^12 cm^-2 were created in the experiments. Trap formation and trap relaxation are distinctly different above and below ~280 K. In devices in which a self-assembled monolayer on top of the SiO2 provides a hydrophobic insulator surface we do not observe trap formation. These results indicate the microscopic cause of the trap state to be water adsorbed on the SiO2 surface.
The 1/f noise in pentacene thin film transistors has been measured as a function of device thickness from well above the effective conduction channel thickness to only two conducting layers. Over the entire thickness range, the spectral noise form is 1/f, and the noise parameter varies as (gate voltage)-1, confirming that the noise is due to mobility fluctuations, even in the thinnest films. Hooge's parameter varies as an inverse power-law with conductivity for all film thicknesses. The magnitude and transport characteristics of the spectral noise are well explained in terms of percolative eff…
We measure the complex impedance between source/drain electrodes and the gate electrode of a pentacene thin-film transistor (TFT) at frequencies 50 Hz < omega/2pi < 20 kHz. Modeling the TFT as a distributed RC network (RC transmission line), we find that the data cannot be explained by a model including only a real, frequency-independent sheet conductivity. Instead, we use the RC transmission line model to extract the frequency-dependent complex sheet conductivity sigma(omega) = sigma'(omega) + jsigma"(omega) of the pentacene film. At high frequencies, sigma(omega) increases with frequency, si…
We show that the performance of pentacene transistors can be significantly improved by maximizing the interfacial area at single walled carbon nanotube (SWCNT)/pentacene. The interfacial areas are varied by anchoring short SWCNTs of different densities (0-30/μm) to the Pd electrodes. The average mobility is increased three, six and nine times for low, medium and high SWCNT densities, respectively, compared to the devices with zero SWCNT. The current on-off ratio and on-current are increased up to 40 times and 20 times with increasing the SWCNT density. We explain the improved device performanc…
The thermal deposition and transfer Printing method had been used to produce pentacene thin-films on SiO2/Si and plastic substrates (PMMA and PVP), respectively. X-ray diffraction patterns of pentacene thin films showed reflections associated with highly ordered polycrystalline films and a coexistence of two polymorph phases classified by their d-spacing, d(001): 14.4 and 15.4 A.The dependence of the c-axis correlation length and the phase fraction on the film thickness and printing temperature were measured. A transition from the 15.4 A phase towards 14.4 A phase was also observed with increa…
We present a simple but powerful method to determine the thicknesses of the accumulation and depletion layers and the distribution curve of injected carriers in organic field effect transistors. The conductivity of organic semiconductors in thin film transistors was measured in-situ and continuously with a bottom contact configuration, as a function of film thickness at various gate voltages. Using this method, the thicknesses of the accumulation and depletion layers of pentacene were determined to be 0.9 nm (VG=-15 V) and 5 nm (VG=15 V).
The spectral density of localized states in the band gap of pentacene (trap DOS) was determined with a pentacene-based thin-film transistor from measurements of the temperature dependence and gate-voltage dependence of the contact-corrected field-effect conductivity. Several analytical methods to calculate the trap DOS from the measured data were used to clarify, if the different methods lead to comparable results. We also used computer simulations to further test the results from the analytical methods. Most methods predict a trap DOS close to the valence band edge that can be very well appro…
The surface conductivity is measured by a four-probe technique for pentacene and rubrene single-crystals laminated on polarized and nearly unpolarized molecular monolayers with application of perpendicular electric fields. The polarization of the self-assembled monolayers (SAMs) shifts the threshold gate voltage, while maintaining a very low subthreshold swing of the single-crystal devices (0.11 V/decade). The results, excluding influences of parasitic contacts and grain boundaries, demonstrate SAM-induced nanoscale charge injection up to ~10^12 cm^-2 at the surface of the organic single cryst…
A printing process for high-resolution transfer of all components for organic electronic devices on plastic substrates has been developed and demonstrated for pentacene (Pn), poly (3-hexylthiophene) and carbon nanotube (CNT) thin-film transistors (TFTs). The nanotransfer printing process allows fabrication of an entire device without exposing any component to incompatible processes and with reduced need for special chemical preparation of transfer or device substrates. Devices on plastic substrates include a Pn TFT with a saturation, field-effect mobility of 0.09 cm^2 (Vs)^-1 and on/off ratio …
We report a detailed comparison on the role of a self-assembled monolayer (SAM) of dipolar molecules on the threshold voltage and charge carrier mobility of organic field-effect transistor (OFET) made of both amorphous and polycrystalline organic semiconductors. We show that the same relationship between the threshold voltage and the dipole-induced charges in the SAM holds when both types of devices are fabricated on strictly identical base substrates. Charge carrier mobilities, almost constant for amorphous OFET, are not affected by the dipole in the SAMs, while for polycrystalline OFET (pent…
We have used an electro-optic technique to measure the position-dependent infrared absorption of holes injected into a thin crystal of the organic semiconductor, 6,13-bis(triisopropylsilylethynyl)-pentacene incorporated in a field-effect transistor. By applying square-wave voltages of variable frequency to the gate or drain, one can measure the time it takes for charges to accumulate on the surface, and therefore determine their mobility.
We demonstrate an approach to improve poly-3-hexylthiophene field effect transistors by modifying the gold contacts with monolayer thick pentacenequinone (PQ) or naphthalene (NL). The effective contact resistance is reduced by a factor of two and sixteen for interlayers of PQ and NL, respectively. The observation is attributed to different injection barriers at the metal-organic interface caused by the functionalization and to an additional tunneling barrier enhancing the on/off ratios. This barrier yields to activation energies of 37meV (NL) and 104meV (PQ) below 190K, which are smaller than …
Graphene is an attractive material for microelectronics applications, given such favourable electrical characteristics as high mobility, high operating frequency, and good stability. If graphene is to be implemented in electronic devices on a mass scale, then it must be compatible with existing semiconductor industry fabrication processes. Unfortunately, such processing introduces defects and impurities to the graphene, which cause scattering of the charge carriers and changes in doping level. Scattering results in degradation of electrical performance, including lower mobility and Dirac point…
We show that it is possible to reach one of the ultimate goals of organic electronics: producing organic field-effect transistors with trap densities as low as in the bulk of single crystals. We studied the spectral density of localized states in the band gap (trap DOS) of small molecule organic semiconductors as derived from electrical characteristics of organic field-effect transistors or from space-charge-limited-current measurements. This was done by comparing data from a large number of samples including thin-film transistors (TFT's), single crystal field-effect transistors (SC-FET's) and…
Transition-metal dichalcogenides (TMDCs) are important class of two-dimensional (2D) layered materials for electronic and optoelectronic applications, due to their ultimate body thickness, sizable and tunable bandgap, and decent theoretical room-temperature mobility of hundreds to thousands cm2/Vs. So far, however, all TMDCs show much lower mobility experimentally because of the collective effects by foreign impurities, which has become one of the most important limitations for their device applications. Here, taking MoS2 as an example, we review the key factors that bring down the mobility in…
Understanding charge transport in organic semiconductors in large electric fields is relevant to many applications. We present transport measurements in organic field-effect transistors based on poly(3-hexylthiophene) and 6,13-bis(triisopropyl-silylethynyl) pentacene with short channels, from room temperature down to 4.2 K. Near 300 K transport in both systems is well described by thermally assisted hopping with Poole-Frenkel-like enhancement of the mobility. At low temperatures and large gate voltages, transport in both materials becomes nearly temperature independent, crossing over into fiel…
We use a frequency-dependent electro-optic technique to measure the hole mobility in small molecule organic semiconductors, such as 6,13 bis(triisopropylsilylethynyl)-pentacene. Measurements are made on semiconductor films in bottom gate, bottom contact field-effect transistors (FETs.) Because of the buried metal layer effect the maximum response, due to absorption in the charge layer, will be for a dielectric film ~ 1/4 of a wavelength (in the dielectric) (e.g. ~ 1 micron thick in the infrared.) Results are presented for FETs prepared with both spin-cast polymer and alumina dielectrics prepar…
We report the 1/f noise characteristics at low-frequency in graphene field-effect transistors that utilized a high-k dielectric tantalum oxide encapsulated layer (a few nanometers thick) placed by atomic layer deposition on Si3N4. A low-noise level of ~ 2.2 x 10^(-10) Hz-1 has been obtained at f = 10 Hz. The origin and physical mechanism of the noise can be interpreted by the McWhorter context, where fluctuations in the carrier number contribute dominantly to the low-frequency noise. Optimizing fabrication processes reduced the number of charged impurities in the graphene field-effect transist…
We demonstrate controllable shift of the threshold voltage and the turn-on voltage in pentacene thin film transistors and rubrene single crystal field effect transistors (FET) by the use of nine organosilanes with different functional groups. Prior to depositing the organic semiconductors, the organosilanes were applied to the SiO2 gate insulator from solution and form a self assembled monolayer (SAM). The observed shift of the transfer characteristics range from -2 to 50 V and can be related to the surface potential of the layer next to the transistor channel. Concomitantly the mobile charge …
We show that the temperature dependence of conductivity of high mobility organic crystals Pentacene and Rubrene can be quantitatively described in the framework of the model where carriers are scattered by quenched local impurities and interact with phonons by Su-Schrieffer-Hegger (SSH) coupling. Within this model, we present approximation free results for mobility and optical conductivity obtained by world line Monte Carlo, which we generalize to the case of coupling both to phonons and impurities. We find fingerprints of carrier dynamics in these compounds which differ from conventional meta…
Effects of residual C impurities and Ga vacancies on the dynamic instabilities of AlN/AlGaN/GaN metal insulator semiconductor high electron mobility transistors are investigated. Secondary ion mass spectroscopy, positron annihilation spectroscopy, steady state and time-resolved photoluminescence (PL) measurements have been performed in conjunction with electrical characterization and current transient analyses. The correlation between yellow luminescence (YL), C- and Ga vacancy concentration is investigated. Time-resolved PL indicating the C$_{\mathrm{N}}$O$_{\mathrm{N}}$ complex as the main s…
Two-dimensional semiconductors are structurally ideal channel materials for the ultimate atomic electronics after silicon era. A long-standing puzzle is the low carrier mobility (μ) in them as compared with corresponding bulk structures, which constitutes the main hurdle for realizing high-performance devices. To address this issue, we perform combined experimental and theoretical study on atomically thin MoS2 field effect transistors with varying the number of MoS2 layers (NLs). Experimentally, an intimate relation is observed with a 10-fold degradation in μ for extremely thinned monolayer ch…
The combination of high-quality Al2O3 dielectric and thiol chemistry passivation can effectively reduce the density of interface traps and Coulomb impurities of WS2, leading to a significant improvement of the mobility and a transition of the charge transport from the insulating to the metallic regime. A record high mobility of 83 cm2/Vs (337 cm2/Vs) is reached at room temperature (low temperature) for monolayer WS2. A theoretical model for electron transport is also developed.
Substantial progress on field effect transistors "FETs" consisting of semiconducting single wall carbon nanotubes "s-SWNTs" without detectable traces of metallic nanotubes and impurities is reported. Nearly perfect removal of metallic nanotubes is confirmed by optical absorption, Raman measurements, and electrical measurements. This outstanding result was made possible in particular by ultracentrifugation (150 000 g) of solutions prepared from SWNT powders using polyfluorene as an extracting agent in toluene. Such s-SWNTs processable solutions were applied to realize FET, embodying randomly or…
We have fabricated suspended few layer (1-3 layers) graphene nanoribbon field effect transistors from unzipped multiwall carbon nanotubes. Electrical transport measurements show that current-annealing effectively removes the impurities on the suspended graphene nanoribbons, uncovering the intrinsic ambipolar transfer characteristic of graphene. Further increasing the annealing current creates a narrow constriction in the ribbon, leading to the formation of a large band-gap and subsequent high on/off ratio (which can exceed 104). Such fabricated devices are thermally and mechanically stable: re…
We report low temperature scanning tunneling microscopy characterization of MoSe2 crystals, and the fabrication and electrical characterization of MoSe2 field-effect transistors on both SiO2 and parylene-C substrates. We find that the multilayer MoSe2 devices on parylene-C show a room temperature mobility close to the mobility of bulk MoSe2 (100 cm2V-1s-1 - 160 cm2V-1s-1), which is significantly higher than that on SiO2 substrate (~50 cm2V-1s-1). The room temperature mobility on both types of substrates are nearly thickness independent. Our variable temperature transport measurements reveal a …
Diamond has attracted attention as a next-generation semiconductor because of its various exceptional properties such as a wide bandgap and high breakdown electric field. Diamond field effect transistors, for example, have been extensively investigated for high-power and high-frequency electronic applications. The quality of their charge transport (i.e., mobility), however, has been limited due to charged impurities near the diamond surface. Here, we fabricate diamond field effect transistors by using a monocrystalline hexagonal boron nitride as a gate dielectric. The resulting high mobility o…
We have produced solution-processed thin films of 6,13-bis(triisopropyl-silylethynyl) pentacene with grain sizes from a few micrometers up to millimeter scale by lateral crystallization from a rectangular stylus. Grains are oriented along the crystallization direction, and the grain size transverse to the crystallization direction depends inversely on the writing speed, hence forming a regular array of oriented grain boundaries with controllable spacing. We utilize these controllable arrays to systematically study the role of large-angle grain boundaries in carrier transport and charge trappin…
Tuning of the electronic properties of pre-synthesized colloidal semiconductor nanocrystals (NCs) by doping plays a key role in the prospect of implementing them in printed electronics devices such as transistors, and photodetectors. While such impurity doping reactions have already been introduced, the understanding of the doping process, the nature of interaction between the impurity and host atoms, and the conditions affecting the solubility limit of impurities in nanocrystals are still unclear. Here, we used a post-synthesis diffusion based doping reaction to introduce Ag impurities into I…
Substrate plays a crucial role in determining transport and low frequency noise behavior of graphene field effect devices. Typically, heavily dope Si/SiO$_2$ substrate is used to fabricate these devices for efficient gating. Trapping-detrapping processes closed to the graphene/substrate interface are the dominant sources of resistance fluctuations in the graphene channel, while Coulomb fluctuations arising due to any remote charge fluctuations inside the bulk of the substrate are effectively screened by the heavily doped substrate. Here, we present electronic transport and low frequency noise …
A Bi2Se3 topological insulator field effect transistor is investigated by using ionic liquid as an electric double layer gating material, leading to a conductance modulation of 365% at room temperature. We discuss the role of charged impurities on the transport properties. The conductance modulation with gate bias is due to a change in the carrier concentration, whereas the temperature dependent conductance change is originated from a change in mobility. Large conductance modulation at room temperature along with the transparent optical properties makes topological insulators as an interesting…
The performance of strained silicon as the channel material for transistors has plateaued. Motivated by increasing charge-carrier mobility within the device channel to improve transistor performance, germanium (Ge) is considered as an attractive option as a silicon replacement due to its highest p-type mobility in all of the known semiconductor materials and being compatible with today's conventional CMOS manufacturing process. However, the intrinsically high carrier mobility of Ge becomes significantly degraded because Ge's native oxide is unstable and readily decomposes into several GexOy su…
Graphene-oxide hybrid structures offer the opportunity to combine the versatile functionalities of oxides with the excellent electronic transport in graphene. Understanding and controlling how the dielectric environment affects the intrinsic properties of graphene is also critical to fundamental studies and technological development of graphene. Here we review our recent effort on understanding the transport properties of graphene interfaced with ferroelectric Pb(Zr,Ti)O_3 (PZT) and high-k HfO_2. Graphene field effect devices prepared on high-quality single crystal PZT substrates exhibit up to…
