A circular disc impacting on a water surface creates a remarkably vigorous jet. Upon impact an axisymmetric air cavity forms and eventually pinches off in a single point halfway down the cavity. Immediately after closure two fast sharp-pointed jets are observed shooting up- and downwards from the closure location, which by then has turned into a stagnation point surrounded by a locally hyperbolic flow pattern. This flow, however, is {\it not} the mechanism feeding the two jets. Using high-speed imaging and numerical simulations we show that jetting is fed by the local flow around the base of the jet, which is forced by the colliding cavity walls. Based on this insight, we then show how the analytical description of a collapsing void (using a line of sinks along the axis of symmetry) can be continued beyond the time of pinch-off to obtain a quantitative model for jet formation which is in good agreement with the numerical and experimental data.
Melt electrowriting (MEW) is an extrusion-based additive manufacturing technology to create a complex construct with micro-scale fidelity. The elevated nozzle-to-collector distance of MEW needs a high requirement to control the charged jet, which relies on the understanding of the corresponding jet kinematics at different printing conditions. This study focuses on investigating the effect of printing speed on jet diameter and jet speed along the spinline from Taylor-cone to landing point, suggesting that the fiber diameter decreases linearly with the increment of printing speed; the jet speed …
Numerical simulation of high-speed turbulent water jets in air and its validation with experimental data has not been reported in the literature. It is therefore aimed to simulate the physics of these high-speed water jets and compare the results with the existing experimental works. High-speed water jets diffuse in the surrounding atmosphere by the processes of mass and momentum transfer. Air is entrained into the jet stream and the entire process contributes to jet spreading and subsequent pressure decay. Hence the physical problem is in the category of multiphase flows, for which mass and m…
A small, spherical bubble of high internal pressure is inserted into water at constant ambient pressure as a model of a laser-induced bubble. Its subsequent dynamics near a flat solid boundary is studied in dependence on the distance of the bubble to the boundary by numerically solving the Navier-Stokes equations with the help of the open source software environment OpenFOAM. Implemented is the finite volume method for discretization of the equations of motion and the volume of fluid method for capturing the interface between the bubble interior and exterior. The bubble contains a small amount…
The behaviour of a high viscosity complex fluid upon impact with a dry solid surface has been studied. Video-based studies show the appearance of secondary jets for large impact velocities.
The collapse of a vapor bubble near a flat solid boundary results in the formation of a jet that is directed towards the boundary. In more complex geometries such as corners, predictions of the collapse cannot be made in a straightforward manner due to the loss of axial symmetry. We experimentally investigate the bubble collapse and jet formation in corners formed of two flat solid boundaries with different opening angles. Using potential flow analysis, we accurately predict the direction of the jet and bubble displacement. We further show that for a corner with an opening angle $α$, there exi…
From everyday experience, we all know that a solid edge can deflect a liquid flowing over it significantly, up to the point where the liquid completely sticks to the solid. Although important in pouring, printing and extrusion processes, there is no predictive model of this so-called "teapot effect". By grazing vertical cylinders with inclined capillary liquid jets, we here use the teapot effect to attach the jet to the solid and form a new structure: the liquid helix. Using mass and momentum conservation along the liquid stream, we first quantitatively predict the shape of the helix and then …
A solid object impacting on liquid creates a liquid jet due to the collapse of the impact cavity. Using visualization experiments with smoke particles and multiscale simulations we show that in addition a high-speed air-jet is pushed out of the cavity. Despite an impact velocity of only 1 m/s, this air-jet attains \emph{supersonic} speeds already when the cavity is slightly larger than 1 mm in diameter. The structure of the air flow resembles closely that of compressible flow through a nozzle -- with the key difference that here the "nozzle" is a \emph{liquid} cavity shrinking rapidly in time.
Jet droplets from bubble bursting are determined by a limited parametrical space: the liquid properties (surface tension, viscosity, and density), mother bubble size and acceleration of gravity. Thus, the two resulting parameters from dimensional analysis (usually, the Ohnesorge and Bond numbers, Oh and Bo) completely define this phenomenon when both the trapped gas in the bubble and the environment gas have negligible density. A detailed physical description of the ejection process to model both the ejected droplet radius and its initial launch speed is provided, leading to a scaling law incl…
Using high-speed photography coupled with optical interference, we experimentally study the air entrapment during a liquid drop impacting a solid substrate. We observe the formation of a compressed air film before the liquid touches the substrate, with internal pressure considerably higher than the atmospheric value. The degree of compression highly depends on the impact velocity, as explained by balancing the liquid deceleration with the large pressure of compressed air. After contact, the air film expands vertically at the edge, reducing its pressure within a few tens of microseconds and pro…
It is generally accepted that the Worthington jet occurs when a droplet impacts onto a liquid pool. However, in this experimental study of the impact of viscous droplets onto a less-viscous liquid pool, we identify another jet besides the Worthington jet, forming a two-jet phenomenon. The two jets, a surface-climbing jet and the Worthington jet, may appear successively during one impact event. By carefully tuning the impact condition, we find that the two-jet phenomenon is jointly controlled by the droplet-pool viscosity ratio, the droplet Weber number, and the droplet-pool miscibility. The me…
In the present work we formulated the boundary-value-problem, comprising partial differential equations (PDEs) of steady flow for laminar/turbulent circular jet of a micropolar fluid. A new boundary layer-similarity transformation/solution was derived which is valid not only for the Newtonian fluids but also for the micropolar fluids. Through this transformation PDEs are transformed into the ordinary differential equations (ODEs). These ODEs were solved numerically by the finite-difference method. The obtained results were compared with existing results [9] for the Newtonian fluids. The compar…
A complete understanding of jet dynamics is greatly enabled by accurate separation of the acoustically efficient wavepackets from their higher-energy convecting turbulent counterparts. Recent developments using Momentum Potential Theory (MPT) have successfully isolated the acoustic component in all regions of the jet, to better understand the dynamics as well as to develop wavepacket models. MPT is however a data-intensive method since the inherent Poisson equation solution requires fluctuation quantities in the entire flowfield; as such, it has to date been applied only to numerically obtaine…
Deformation of liquid droplets by impingement induces Worthington jet in certain range of the impact velocity. Although the growth of the jet as well as its tip velocity is predicted from similar cases to the droplet impact, the mechanism of the jet generation is yet to be understood. In this study, high-speed visualization of the droplet impact on a superhydrophobic surface was conducted to understand the initiation of the jet generated by a collapse of an air cavity. Water droplets whose diameter are 2.0 mm and 3.0 mm were generated and the Weber number of the droplet was varied in a range o…
In this fluid dynamics video prepared for the APS-DFD Gallery of Fluid Motion we study the collision of two identical viscous jets at different jet speeds and collision eccentricities. The dynamics of the jet motion are slowed down by orders of magnitude using a synchronized strobe effect coupled with precise timing control of the perturbation frequency imposed on one of the jets. Our results show that different shapes and morphologies appear as we change the collision eccentricity. At low jet speeds ($We_j = 45$) viscous threads and filaments are formed as the jets begin to impinge on each ot…
we report an ultrafast synchrotron x-ray phase contrast imaging study of the primary breakup mechanism of a coaxial air-assisted water jet. We demonstrate that there exist great similarities in the phenomenology of primary breakup with that of the secondary breakup. Especially, a membrane-mediated breakup mechanism dominates the breakup process for a wide range of air speeds. This finding reveals the intrinsic connections of these two breakup regimes and has deep implications on the unified theoretical approach in treating the breakup mechanism of high speed liquid jet.
Fast liquid jets, called micro-jets, are produced within cavitation bubbles experiencing an aspherical collapse. Here we review micro-jets of different origins, scales and appearances, and propose a unified framework to describe their dynamics by using an anisotropy parameter $ζ$, representing a dimensionless measure of the liquid momentum at the collapse point (Kelvin impulse). This parameter is rigorously defined for various jet drivers, including gravity and nearby boundaries. Combining theoretical considerations with hundreds of high-speed visualisations of bubbles collapsing near a rigid …
Helped by the careful analysis of their experimental data, Worthington (1897) described roughly the mechanism underlying the formation of high-speed jets ejected after the impact of an axisymmetric solid on a liquid-air interface. In this work we combine detailed boundary-integral simulations with analytical modeling to describe the formation and break-up of such Worthington jets in two common physical systems: the impact of a circular disc on a liquid surface and the release of air bubbles from an underwater nozzle. We first show that the jet base dynamics can be predicted for both systems us…
A series of Direct Numerical Simulations (DNS) of lean methane/air flames was conducted in order to investigate the enhancement of the turbulent flame speed and modifications to the reaction layer structure associated with the systematic increase of the integral scale of turbulence $l$ while the Karlovitz number and the Kolmogorov scale are kept constant. Four turbulent slot jet flames are simulated at increasing Reynolds number and up to $Re \approx 22000$, defined based on the bulk velocity, slot width, and the reactants' properties. The turbulent flame speed $S_T$ is evaluated locally at se…
The objective of this work is to investigate the coupling of fluid dynamics, heat transfer and mass transfer during the impact and evaporation of droplets on a heated solid substrate. A laser-based thermoreflectance method is used to measure the temperature at the solid-liquid interface, with a time and space resolution of 100 μs and 20 μm, respectively. Isopropanol droplets with micro- and nanoliter volumes are considered. A finite-element model is used to simulate the transient fluid dynamics and heat transfer during the droplet deposition process, considering the dynamics of wetting as well…
The impact of solid and liquid objects (projectiles) onto liquids and soft solids (targets) generally results on the creation and expansion of an air cavity inside the impacted objects. The dynamics of cavity expansion and collapse depends on the projectile inertia as well as on the target properties. In this paper we study the impact of microfluidic jets generated by thermocavitation processes on a capillary bridge between two parallel planar walls. Different capillary bridge types were studied, Newtonian liquids, viscoelastic liquids and agarose gels. Thus, we compare the cavity formation an…
Numerical solutions of high-speed microdroplet impact onto a smooth solid surface are computed, using the interFoam VoF solver of the OpenFOAM CFD package. Toward the solid surface, the liquid microdroplet is moving with an impinging gas flow, simulating the situation of ink droplets being deposited onto substrate with a collimated mist jet in the Optomec Aerosol Jet printing process. The computed values of maximum spread factor, for the range of parameters of practical interest to Aerosol Jet printing, were found in very good agreement with some of the correlation formulas proposed by previou…
Motivated by the aero-acoustic feedback loop phenomenon in high speed free jets and impinging jets, a thorough examination of a POD (Proper Orthogonal Decomposition)-Galerkin method to determine the average convection velocity of coherent structures in the shear layer is presented in this paper. The technique is shown to be applicable to both time resolved as well as time unresolved data, if the data set meets certain requirements. Using a detailed sensitivity analysis on a synthetic data set, a quantitative estimate on the required time resolution for the technique has been found, which can b…
In this work a numerical model for two-dimensional axisymmetric continuous freezing by impingement of processed meat or similar products in food industry moving along a conveyor belt is presented. The model represents a more computationally efficient alternative to solve conjugate heat transfer between a fluid and a solid, accompanied by phase change in some constituents of the solid phase. In the model presented here it is assumed that the solid can be represented as an homogeneous medium, with its thermophysical properties depending on the temperature. The impingement freezing model is conce…
A liquid jet can stably bounce off a sufficiently soft gel, by following the contour of the dimple created upon impact. This new phenomenon is insensitive to the wetting properties of the gels and was observed for different liquids over a wide range of surface tensions, $γ$ = 24--72 mN/m. In contrast, other jet rebound phenomena are typically sensitive to $γ$: jet rebounds off a hard solid (e.g. superhydrophobic surface) or another liquid are possible only for high and low $γ$ liquids, respectively. This is because an air layer must be stabilized between the two interfaces. For a soft gel, no …
Recent studies found that atmospheric superrotation (i.e., west-to-east winds over the equator) on tidally locked planets can modify the phase of planetary waves. But, a clear relationship between the superrotation and the magnitude of the phase shift was not examined. In this study, we re-investigate this problem using a two-dimensional (2D) linear shallow water model with a specified uniform zonal flow. We find that the degree of the phase shift is a monotonic but nonlinear function of the strength of the mean flow, and the phase shift has two limits of -$π$ and +$π$. The existence of these …
