Cavity-enhanced radiation-pressure coupling of optical and mechanical degrees of freedom gives rise to a range of optomechanical phenomena, in particular providing a route to the quantum regime of mesoscopic mechanical oscillators. A prime challenge in cavity optomechanics has however been to realize systems which simultaneously maximize optical finesse and mechanical quality. Here we demonstrate for the first time independent control over both mechanical and optical degree of freedom within one and the same on-chip resonator. The first direct observation of mechanical normal mode coupling in a micromechanical system allows for a quantitative understanding of mechanical dissipation. Subsequent optimization of the resonator geometry enables intrinsic material loss limited mechanical Q-factors, rivalling the best values reported in the high MHz frequency range, while simultaneously preserving the resonators' ultra-high optical finesse. Besides manifesting a complete understanding of mechanical dissipation in microresonator based optomechanical systems, our results provide an ideal setting for cavity optomechanics.
We propose and analyze a circuit that implements a nonlinear coupling between two superconducting microwave resonators. The resonators are coupled through a superconducting quantum interference device (SQUID) that terminates one of the resonators. This produces a nonlinear interaction on the standard optomechanical form, where the quadrature of one resonator couples to the photon number of the other resonator. The circuit therefore allows for all-electrical realizations of analogs to optomechanical systems, with coupling that can be both strong and tunable. We estimate the coupling strengths t…
We demonstrate that a geometric phase, generated via a sequence of four optomechanical interactions, can be used to increase, or generate nonlinearities in the unitary evolution of a mechanical resonator. Interactions of this form lead to new mechanisms for preparing mechanical squeezed states, and preparation of non-classical states with significant Wigner negativity.
We study the optical transmission characteristics of pump-probe driven spinning optomechanical ring resonators coupled in a series configuration. After performing the steady-state analysis valid for an arbitrary number of resonators, as an example, we discuss the two-resonator problem in detail. Therein, we focus on how changing the optical Sagnac effect due to same or opposite spinning directions of resonators can lead to enhanced, non-reciprocal and delayed probe light transmission. This work can help in devising spin degree of freedom based novel devices of manipulating light propagation in…
We experimentally demonstrate the high-sensitivity optical monitoring of a micro-mechanical resonator and its cooling by active control. Coating a low-loss mirror upon the resonator, we have built an optomechanical sensor based on a very high-finesse cavity (30000). We have measured the thermal noise of the resonator with a quantum-limited sensitivity at the 10^-19 m/rootHz level, and cooled the resonator down to 5K by a cold-damping technique. Applications of our setup range from quantum optics experiments to the experimental demonstration of the quantum ground state of a macroscopic mechanic…
Ground-state cooling of mechanical resonators is an important task in quantum optomechanics, because it is a necessary prerequisite for creation, manipulation, and application of macroscopic mechanical coherence. Here, we propose a transient-state scheme to accelerate ground-state cooling of a mechanical resonator in a three-mode loop-coupled optomechanical system via shortcuts to adiabaticity (STA). We consider four kinds of coupling protocols and calculate the evolution of the mean phonon number of the mechanical resonator in both the adiabatic and STA cases. We verify that the ground-state …
We consider a cavity optomechanical cooling configuration consisting of a mechanical resonator (denoted as resonator b) and an electromagnetic resonator (denoted as resonator a), which are coupled in such a way that the effective resonance frequency of resonator a depends linearly on the displacement of resonator b. We study whether back-reaction effects in such a configuration can be efficiently employed for suppression of decoherence. To that end, we consider the case where the mechanical resonator is prepared in a superposition of two coherent states and evaluate the rate of decoherence. We…
We report the experimental demonstration of optomechanical light storage in a silica resonator. We use writing and readout laser pulses tuned to one mechanical frequency below an optical cavity resonance to control the coupling between the mechanical displacement and the optical field at the cavity resonance. The writing pulse maps a signal pulse at the cavity resonance to a mechanical excitation. The readout pulse later converts the mechanical excitation back to an optical pulse. The light storage lifetime is determined by the relatively long damping time of the mechanical excitation.
A pulsed cooling scheme for optomechanical systems is presented that is capable of cooling at much faster rates, shorter overall cooling times, and for a wider set of experimental scenarios than is possible by conventional methods. The proposed scheme can be implemented for both strongly and weakly coupled optomechanical systems in both weakly and highly dissipative cavities. We study analytically its underlying working mechanism, which is based on interferometric control of optomechanical interactions, and we demonstrate its efficiency with pulse sequences that are obtained by using methods f…
We propose two kinds of distinguishing parameter regimes to induce topological Su-Schrieffer-Heeger (SSH) phase in a one dimensional (1D) multi-resonator cavity optomechanical system via modulating the frequencies of both cavity fields and resonators. The introduction of the frequency modulations allows us to eliminate the Stokes heating process for the mapping of the tight-binding Hamiltonian without usual rotating wave approximation, which is totally different from the traditional mapping of the topological tight-binding model. We find that the tight-binding Hamiltonian can be mapped into a …
We propose a scheme that can generate a tunable double optomechanically induced transparency (OMIT) in a hybrid optomechanical cavity system, in which the mechanical resonator of an optomechanical cavity is coupled to an additional mechanical resonator, and the additional mechanical resonator can be driven by a weak external coherently mechanical driving field. We show that both the intensity and the phase of the the external mechanical driving field can control the propagation of the probe field, including changing the transmission spectrum curve from a double-window to a single-window. Our s…
We theoretically propose a scheme for the generation of a non-classical single-mode motional state of a mechanical resonator (MR) in the three-mode optomechanical systems, in which two optical modes of the cavities are linearly coupled to each other and one mechanical mode of the MR is optomechanically coupled to the two optical modes with the same coupling strength simultaneously. One cavity is driven by a coherent laser light. By properly tuning the frequency of the weak driving field, we obtain engineered Liouvillian superoperator via engineering the selective interaction Hamiltonian confin…
A standard model is suggested to explore correlation features of two spatially separated optomechanical cavities. The cavities are coupled through the photon-hopping process. In particular, we investigate the generation of entanglement between mechanical resonators in the strong coupling regime and the two cavities are assumed to be driven by a coherent laser field. In order to quantify entanglement we use the logarithmic negativity. The analytical solutions are presented for the system in a parameter regime very close to the current experimental results. We show that in the presence of the ph…
We propose to cool a mechanical resonator close to its ground state via an electromagnetically-induced-transparency- (EIT-) like cooling mechanism in a double-cavity optomechanical system, where an additional cavity couples to the original one in the standard optomechanical system. By choosing optimal parameters such that the cooling process of the mechanical resonator corresponds to the maximum value of the optical fluctuation spectrum and the heating process to the minimum one, the mechanical resonator can be cooled with the final mean phonon number less than that at the absence of the addit…
Synchronization has great impacts in various fields such as self-clocking, communication, neural networks, etc. Here we present a mechanism of synchronization for two mechanical modes in two coupled optomechanical resonators by introducing the so-called PT-symmetric structure. It is shown that the degree of synchronization between the two far-off-resonant mechanical modes can be increased by decreasing the coupling strength between the two optomechanical resonators. Additionally, when we consider the stochastic noises in the optomechanical resonators, we find that more noises can enhance the d…
We investigate theoretically the influence of laser phase noise on the cooling and heating of a generic cavity optomechanical system. We derive the back-action damping and heating rates and the mechanical frequency shift of the radiation pressure-driven oscillating mirror, and derive the minimum phonon occupation number for small laser linewidths. We find that in practice laser phase noise does not pose serious limitations to ground state cooling. We then consider the effects of laser phase noise in a parametric cavity driving scheme that minimizes the back-action heating of one of the quadrat…
We give a theoretical study of a double-cavity system in which a mechanical resonator beam is coupled to two cavity modes on both sides through radiation pressures. The indirect coupling between the cavities via the resonator sets up a correlation in the optomechanical entanglements between the two cavities with the common resonator. This correlation initiates an entanglement transfer from the intracavity photon-phonon entanglements to an intercavity photon-photon entanglement. Using numerical solutions, we show two distinct regimes of the optomechanical system, in which the indirect entanglem…
We propose a method to decouple the nanomechanical resonator in optomechanical systems from the environmental noise by introducing a chaotic coherent feedback loop. We find that the chaotic controller in the feedback loop can modulate the dynamics of the controlled optomechanical system and induce a broadband response of the mechanical mode. This broadband response of the mechanical mode will cut off the coupling between the mechanical mode and the environment and thus suppress the environmental noise of the mechanical modes. As an application, we use the protected optomechanical system to act…
We systematically study the influence of simultaneously modulating the input laser intensity and quantum dot (QD) resonance frequecy on the mean-field dynamics, fluctuation energy transfer and entanglement in a optomechanical semi-conductor resonator embedded with a QD. We show that the modulation and the hybrid system can be engineered to attain the desired mean-field values, control the fluctuation energy transfer and the entanglement between the various degrees of freedom. A remarkably high degree of entanglement can be achieved by modulating only the QD frequency. The interplay between the…
We describe a new approach for on-chip optical non-reciprocity which makes use of strong optomechanical interaction in microring resonators. By optically pumping the ring resonator in one direction, the optomechanical coupling is only enhanced in that direction, and consequently, the system exhibits a non-reciprocal response. For different configurations, this system can function either as an optical isolator or a coherent non-reciprocal phase shifter. We show that the operation of such a device on the level of single-photon could be achieved with existing technology.
We propose and analyze a microscopic Stirling heat engine based on an optomechanical system. The working fluid is a single vibrational mode of a mechanical resonator, which interacts by radiation pressure with a feedback-controlled optical cavity. The cavity light is used to engineer the thermal reservoirs and to steer the resonator through a thermodynamic cycle. In particular, the feedback is used to properly modulate the light fluctuations inside the cavity and hence to realize efficient thermodynamic transformations with realistic optomechanical devices.
We demonstrate a centimeter-scale optomechanical magnetometer based on a crystalline whispering gallery mode resonator. The large size of the resonator allows high magnetic field sensitivity to be achieved in the hertz to kilohertz frequency range. A peak sensitivity of 131 pT per root Hz is reported, in a magnetically unshielded non-cryogenic environment and using optical power levels beneath 100 microWatt. Femtotesla range sensitivity may be possible in future devices with further optimization of laser noise and the physical structure of the resonator, allowing applications in high-performan…
We realize a superconducting circuit analog of the generic cavity-optomechanical Hamiltonian by longitudinally coupling two superconducting resonators, which are an order of magnitude different in frequency. We achieve longitudinal coupling by embedding a superconducting quantum interference device (SQUID) into a high frequency resonator, making its resonance frequency depend on the zero point current fluctuations of a nearby low frequency LC-resonator. By employing sideband drive fields we enhance the intrinsic coupling strength of about 15 kHz up to 280 kHz by controlling the amplitude of th…
We study the phonon dynamics in lattices of optomechanical resonators where the mutually coupled photonic modes are coherently driven and the mechanical resonators are uncoupled and connected to independent thermal baths. We present a general procedure to obtain the effective Lindblad dynamics of the phononic modes for an arbitrary lattice geometry, where the light modes play the role of an effective reservoir that mediates the phonon nonequilibrium dynamics. We show how to stabilize stationary states exhibiting directional heat currents over arbitrary distance, despite the absence of thermal …
We explore theoretically the optical response properties in an optomechanical system under electromagneti- cally induced transparency condition but with the mechanical resonator being driven by an additional coherent field. In this configuration, more complex quantum coherent and interference phenomena occur. In partic- ular, we find that the probe transmission spectra depend on the total phase of the applied fields. Our study also provides an efficient way to control propagation of amplification.
We report the experimental demonstration of converting coherent optical fields between two different optical wavelengths by coupling two optical modes to a mechanical breathing mode in a silica resonator. The experiment is based on an itinerant approach, in which state-mapping from optical to mechanical and from mechanical to another optical state takes place simultaneously. In contrast to conventional nonlinear optical processes, optomechanical impedance matching as well as efficient optical input-output coupling, instead of phase-matching, plays a crucial role in optomechanics-based waveleng…
We determine the theoretical limits to squeezing-enhanced measurement sensitivity of mechanical motion in a cavity optomechanical system. The motion of a mechanical resonator is transduced onto quadrature fluctuations of a cavity optical field and a measurement is performed on the optical field exiting the cavity. We compare measurement sensitivities obtained with coherent probing and quantum-enhanced probing of the mechanical motion, i.e. the coherent probe field carries vacuum states and quadrature squeezed vacuum states at sideband frequencies, respectively. We find that quantum-enhanced pr…
Optomechanics concerns with the coupling between optical cavities and mechanical resonators. Most early works are concentrated in the physics of optomechanics in the small-displacement regime and consider one single optical cavity mode participating in the optomechanical coupling. In this paper, we focus on optomechanics in the extremely-large-amplitude regime in which a mechanical resonator is coupled with multiple optical cavity modes during the oscillation. We explicitly show that the mechanical resonator can present self-sustained oscillations in a novel way with limit cycles in the shape …
We study photon blockade and anti-bunching in the cavity of an optomechanical system in which the mechanical resonator is coupled to a two-level system (TLS). In particular, we analyze the effects of the coupling strength (to the mechanical mode), transition frequency, and decay rate of TLS on the photon blockade. The statistical properties of the cavity field are affected by the TLS, because the TLS changes the energy-level structure of the optomechanical system via dressed states formed by the TLS and the mechanical resonator. We find that the photon blockade and tunneling can be significant…
The search for experimental demonstrations of the quantum behavior of macroscopic mechanical resonators is a fastly growing field of investigation and recent results suggest that the generation of quantum states of resonators with a mass at the microgram scale is within reach. In this chapter we give an overview of two important topics within this research field: cooling to the motional ground state, and the generation of entanglement involving mechanical, optical and atomic degrees of freedom. We focus on optomechanical systems where the resonator is coupled to one or more driven cavity modes…
We theoretically study high-order optomechanically-induced transparency (OMIT) process in a nonlinear Kerr resonator. A frequency shift induced by the Kerr effect, is identified for the optical cavity mode, which results in asymmetric OMIT windows of the signal and its higher-order sidebands. We also find that both the sideband amplitude and its associated group delay sensitively depend on the strength of the Kerr nonlinearity. This indicates the possibility to enhance or steer the performance of OMIT devices with various nonlinear optical cavities.
We study in detail the dynamics of a non-stationary system composed of a Quantum Well confined in an optomechanical cavity. This system is investigated with classical and quantized motion of the cavity movable mirror. In both the cases, the cavity frequency is rapidly modulated in time. The resultant periodically modulated spectra is presented. In particular, we study the effect of two-photon process on the number of intracavity photons. The intensity of fluorescent light emitted by excitons in the quantum well is also examined for these non-stationary systems. It is observed that the initial …
We propose a quantum interference cooling scheme for a nano-mechanical resonator (NAMR) in a hybrid optomechanical system, where the atoms are trapped in an optomechanical cavity, coupling to an additional optical cavity. The absorption of the optomechanical resonator can be modified by quantum interference effects induced by the atom-cavity and cavity-cavity couplings independently. With the employment of the quantum interference, the desired transition for cooling is enhanced, along with the heating suppression due to the undesired transition. As a result, the NAMR vibration can be cooled do…
In the framework of the nonsecular perturbation theory based on the Bogoliubov averaging method, an optomechanical system with an asymmetric anharmonic mechanical resonator is studied. The cross-Kerr interaction and the Kerr-like self-interaction of photons and vibration quanta arise in the Hamiltonian. These interactions are induced by both cubic and quartic nonlinearities of oscillations of the mechanical resonator and the cavity-resonator interaction that is linear in mechanical displacements. We demonstrate a bistable behavior of the number of vibration quanta and find that this behavior i…
We theoretically study a strongly-driven optomechanical system which consists of a passive optical cavity and an active mechanical resonator. When the optomechanical coupling strength is varied, phase transitions, which are similar those observed in $\mathcal{PT}$-symmetric systems, are observed. We show that the optical transmission can be controlled by changing the gain of the mechanical resonator and loss of the optical cavity mode. Especially, we find that: (i) for balanced gain and loss, optical amplification and absorption can be tuned by changing the optomechanical coupling strength thr…
Optical measurements of a nanoscale silicon optomechanical crystal cavity with a mechanical resonance frequency of 3.6GHz are performed at sub-kelvin temperatures. We infer optical-absorption-induced heating and damping of the mechanical resonator from measurements of phonon occupancy and motional sideband asymmetry. At the lowest probe power and lowest fridge temperature (10mK), the localized mechanical resonance is found to couple at a rate of 400Hz (Q=9x10^6) to a thermal bath of temperature 270mK. These measurements indicate that silicon optomechanical crystals cooled to millikelvin temper…
We adopt the Ramsey's method of separated oscillatory fields to study coherences of the mechanical system in an optomechanical resonator. The high resolution Ramsey fringes are observed in the emission optical field, when two pulses separated in time are applied. We develop a theory to describe the transient optomechanical behavior underlying the Ramsey fringes. We also perform the experimental demonstration using a silica microresonator. The method is versatile and can be adopted to different types of mechanical resonators, electromechanical resonators.
Ground state cooling of massive mechanical objects remains a difficult task restricted by the unresolved mechanical sidebands. We propose an optomechanically-induced-transparency cooling scheme to achieve ground state cooling of mechanical motion without the resolved sideband condition in a pure optomechanical system with two mechanical modes coupled to the same optical cavity mode. We show that ground state cooling is achievable for sideband resolution $ω_{m}/κ$ as low as 0.003. This provides a new route for quantum manipulation of massive macroscopic devices and high-precision measurements.
In this paper, we show how continuous-variable dense coding can be implemented using entangled light generated from a membrane-in-the-middle geometry. The mechanical resonator is assumed to be a high reflectivity membrane hung inside a high quality factor cavity. We show that the mechanical resonator is able to generate an amount of entanglement between the optical modes at the output of the cavity, which is strong enough to approach the capacity of quantum dense coding at small photon numbers. The suboptimal rate reachable by our optomechanical protocol is high enough to outperform the classi…
We use single photon detectors to probe the motional state of a superfluid $^4$He resonator of mass $\sim1$ ng. The arrival times of Stokes and anti-Stokes photons (scattered by the resonator's acoustic mode) are used to measure the resonator's phonon coherences up to the fourth order. By post-selecting on photon detection events, we also measure coherences in the resonator when $\leq3$ phonons have been added or subtracted. These measurements are found to be consistent with predictions that assume the acoustic mode to be in thermal equilibrium with a bath through a Markovian coupling.
Plasmonic dimer cavities can induce extreme electric-field hot spots that allow one to access ultrastrong coupling regimes using Raman-type spectroscopy on single vibrating molecules. Using a generalized master equation, we study resonant Raman scattering in the strong coupling regime of cavity-QED, when also in the vibrational ultrastrong coupling regime, leading to "phonon-dressed polaritons". The master equation rigorously includes spectral baths for the cavity and vibrational degrees of freedom, as well as a pure dephasing bath for the resonant two-level system, which play a significant ro…
Quantum squeezing of mechanical resonator is important for studying the macroscopic quantum effects and the precision metrology of weak forces. Here we give a theoretical study of a hybrid atom-optomechanical system in which the steady-state squeezing of the mechanical resonator can be generated via the mechanical nonlinearity and cavity cooling process. The validity of the scheme is assessed by simulating the steady-state variance of the mechanical displacement quadrature numerically. The scheme is robust against dissipation of the optical cavity, and the steady-state squeezing can be effecti…
We study the physical properties of double-cavity optomechanical system in which the mechanical resonator interacts with one of the coupled cavities and another cavity is used as an auxiliary cavity. The model can be expected to achieve the strong optomechanical coupling strength and overcome the optomechanical cavity decay, simultaneously. Through the coherent auxiliary cavity interferences, the steady-state squeezing of mechanical resonator can be generated in highly unresolved sideband regime. The validity of the scheme is assessed by numerical simulation and theoretical analysis of the ste…
Recent experimental progress in table-top experiments or gravitational-wave interferometers has enlightened the unique displacement sensitivity offered by optical interferometry. As the mirrors move in response to radiation pressure, higher power operation, though crucial for further sensitivity enhancement, will however increase quantum effects of radiation pressure, or even jeopardize the stable operation of the detuned cavities proposed for next-generation interferometers. The appearance of such optomechanical instabilities is the result of the nonlinear interplay between the motion of the …
In the usual optomechanical systems, the stability of the systems severely limits those researches of the macroscopic quantum effects. We study an usual cavity optomechanical system where the frequency of the optical mode is shaken periodically. We find that, when the optical shaking frequency is large enough, the shake of the optical mode can stabilize the system. That means we can study the macroscopic quantum effects of the mechanical resonator even in the strong coupling region where the standard optomechanical systems are always unstable. As examples, we study the ground-state cooling of …
In view of the integration of membrane resonators with more complex MEMS structures, we developed a general fabrication procedure for circular shape SiN$_x$ membranes using Deep Reactive Ion Etching (DRIE). Large area and high-stress SiN$_x$ membranes were fabricated and used as optomechanical resonators in a Michelson interferometer and in a Fabry-Pérot cavity. The measurements show that the fabrication process preserves both the optical quality and the mechanical quality factor of the membrane.
We study the directional amplification of an optical probe field in a three-mode optomechanical system, where the mechanical resonator interacts with two linearly-coupled optical cavities and the cavities are driven by strong optical pump fields. The optical probe field is injected into one of the cavity modes, and at the same time, the mechanical resonator is subject to a mechanical drive with the driving frequency equal to the frequency difference between the optical probe and pump fields. We show that the transmission of the probe field can be amplified in one direction and de-amplified in …
