The bending of a nonconducting piezoelectric ZnO nanowire is simulated by finite element method calculations. The top part is bent by a lateral force, which could be applied by an atomic force microscope (AFM) tip. The generated electrical potential is 0.3 V. This relatively high signal is, however, difficult to measure, due to the low capacitance of the ZnO nanowire (4x10^{-5} pF) as compared to the capacitance of most preamplifiers (5 pF). A further problem arises from the semiconducting properties of experimentally fabricated ZnO nanowires which causes the disappearance of the voltage signal within picoseconds.
Precise control of morphologies of one-dimensional (1D) or 2D nanostructures during growth has not been easily accessible, usually degrading the device performance and therefore limiting applications to various advanced nanoscale electronics and optoelectronics. Graphene could be a platform to serve as a substrate for both morphology control and direct use of electrodes due to its ideal monolayer flatness with π electrons. Here, we report that by using graphene directly as a substrate, vertically well-aligned ZnO nanowires and nanowalls were obtained systematically by controlling Au catalyst t…
Piezoelectric capacitive NanoGenerators (NG) based on vertically grown crystalline zinc oxide nanowires (ZnO-NWs) have been fabricated using a low-cost and scalable hydrothermal method on gold-coated silicon substrates, which served as both a seed layer and a conductive bottom electrode. Morphological and structural characterizations demonstrate that the obtained ZnO NWs are dense, uniformly distributed, vertically well aligned and exhibit good crystal quality. The piezoelectric NG consists of ZnO-NWs grown on a gold-coated silicon substrate, parylene-C matrix, titanium/aluminium top electrode…
Nanogenerators based on piezoelectric materials convert ever-present mechanical vibrations into electrical power for energetically autonomous wireless and electronic devices. Nanowires of piezoelectric polymers are particularly attractive for harvesting mechanical energy in this way, as they are flexible, lightweight and sensitive to small vibrations. Previous studies have focused exclusively on nanowires grown by electrospinning, but this involves complex equipment, and high voltages of $\approx$ 10 kV that electrically pole the nanowires and thus render them piezoelectric. Here we demonstrat…
The thin film configuration presents obvious practical advantages over the 1D implementation in energy harvesting systems such as easily manufacturing and processing and long lasting and stable devices. However, most of the ZnO-based piezoelectric nanogenerators (PENGs) reported so far relay in the exploitation of single-crystalline ZnO nanowires because their self-orientation in the c-axis and ability to accommodate long deformations resulting in a high piezoelectric performance. Herein, we show an innovative approach aiming to produce PENGs by combining polycrystalline ZnO layers fabricated …
Hexagonal [0001] nonpassivated ZnO nanowires are studied with density functional calculations. The band gap and Young's modulus in nanowires which are larger than those in bulk ZnO increase along with the decrease of the radius of nanowires. We find ZnO nanowires have larger effective piezoelectric constant than bulk ZnO due to their free boundary. In addition, the effective piezoelectric constant in small ZnO nanowires doesn't depend monotonously on the radius due to two competitive effects: elongation of the nanowires and increase of the ratio of surface atoms.
We introduce herein the advanced application of low pressure plasma procedures for the development of piezo and triboelectric mode I hybrid nanogenerators. Thus, plasma assisted deposition and functionalization methods are presented as key enabling technologies for the nanoscale design of ZnO polycrystalline shells, the formation of conducting metallic cores in core@shell nanowires, and for the solventless surface modification of polymeric coatings and matrixes. We show how the perfluorinated chains grafting of PDMS provides a reliable approach to increase the hydrophobicity and surface charge…
Controlling the growth of zinc oxide nanowires is necessary to optimize the performances of nanowire-based devices such as photovoltaic solar cells, nano-generators, or light-emitting diodes. In this view, we investigate the nucleation and growth mechanisms of ZnO nanowires grown by metalorganic vapor phase epitaxy either on O-polar ZnO or on sapphire substrates. Whatever the substrate, ZnO nanowires are Zn-polar, as demonstrated by convergent beam electron diffraction. For growth on O-polar ZnO substrate, the nanowires are found to sit on O-polar pyramids. As growth proceeds, the inversion do…
Vertically aligned, beaded zinc germinate (Zn2GeO4)/ zinc oxide (ZnO) hybrid nanowire arrays were successfully synthesized by a vapor-solid process via a catalyst-free approach. The as-synthesized products were characterized using X-ray diffraction, scanning electron microscopy and transmission electron microscopy equipped with an energy-dispersive X-ray spectrometer. TEM studies revealed the beaded microstructures of the Zn2GeO4/ZnO nanowire. Furthermore, Zn2GeO4 nanotubes were synthesized after wet etching treatments on Zn2GeO4/ZnO hybrid nanowires.
The effect of applying an external electric field on doping-induced spin-orbit splitting of the lowest conduction-band states in a bismuth-doped zinc oxide nanowire is studied by performing electronic structure calculations within the framework of density functional theory. It is demonstrated that spin splitting in Bi-doped ZnO nanowires could be tuned and enhanced electrically via control of the strength and direction of the applied electric field, thanks to the nonuniform and anisotropic response of the ZnO:Bi nanowire to external electric fields. The results reported here indicate that a si…
This paper presents two first-principles calculations on the lattice- and electronic- structures of a small-diameter infinite and truncated ZnO nanowire. The two calculations show excellent agreement with each other. For the small diameter nanowire, the lattice and electronic properties are determined by the relaxed surface. We find a similarity between the nanowire surface and the surface of the bulk material, and discuss the assignment of the rotational quantum number m to the bands.
We perform molecular dynamics (MD) simulations to investigate the effect of polar surfaces on the thermal transport in zinc oxide (ZnO) nanowires. We find that the thermal conductivity in nanowires with free polar (0001) surfaces is much higher than in nanowires that have been stabilized with reduced charges on the polar (0001) surfaces, and also hexagonal nanowires without any transverse polar surfaces. From normal mode analysis, we show that the higher thermal conductivity is due to a shell-like reconstruction that occurs for the free polar surfaces. This shell-like reconstruction suppresses…
We performed density-functional calculations to investigate the electronic structure of ZnO/GaN core/shell heterostructured nanowires (NWs) orientating along <0001> direction. The build-in electric filed arising from the charge redistribution at the {1-100} interfaces and the band offsets were revealed. ZnO-core/GaN-shell NWs rather than GaN-core/ZnO-shell ones were predicted to exhibit natural charge spatial separation behaviors, which are understandable in terms of an effective mass model. The effects of quantum confinement on the band gaps and band offsets were also discussed.
In this work, ZnO nanowire arrays decorated with titanium nitride (TiN) nanoparticles as surface enhanced Raman scattering (SERS) substrates is demonstrated. ZnO nanowires were grown by hydrothermal synthesis while ~100 nm TiN nanoparticles were obtained by grinding commercial powders for several hours. They were then decorated on the ZnO nanowire arrays using acetone as the medium. Scanning electron microscopy confirmed the presence of TiN nanoparticles on the ZnO nanowires. TiN nanoparticles exhibited localized surface plasmon resonances at 430, 520 and 600 nm. SERS experiments using Nile Bl…
We investigated both numerically and experimentally the dynamics of individual ZnO nanowires immersed in an in-plane switching (IPS) 4-Cyano-4-pentylbiphenyl (5CB) liquid crystal cell under switching electric fields. Comparing the motion of nanowires captured by a high-speed CCD camera with the simulated results allows the interaction among nanowires, liquid crystals and external electric field to be studied. Our results show that in the nematic phase, the relaxation and response of a nanowire are both controlled by both the dielectrophoretic torque induced by the external electric field and t…
We analyse the morphological, structural and luminescence properties of self-assembled ZnO nanowires grown by chemical vapour transport on Si(001). The examination of nanowire ensembles by scanning electron microscopy reveals that a non-negligible fraction of nanowires merge together forming coalesced aggregates during growth. We show that the coalescence degree can be unambiguously quantified by a statistical analysis of the cross-sectional shape of the nanowires. The examination of the structural properties by X-ray diffraction evidences that the nanowires crystallize in the wurtzite phase, …
In this work we have employed density-functional theory with hybrid functionals to investigate the atomic and electronic structure of bare and hydrogenated Mn doped ZnO nanowires with small diameter. We determine changes in magnetic and electronic structure of Mn-doped ZnO nanowires due to surface effects, such as hydrogen adsorption on the surface, presence of oxygen vacancies and dangling bonds. In the absence of passivation on the nanowire surface, the manganese atoms segregate to the surface, whereas under hydrogen adsorption the incorporation of Mn is energetically more favourable at inne…
Plastic relaxation of the misfit stress in core-shell semi-conducting nanowires can lead to structural defects, detrimental to applications. Core-shell Zn{0.7}Mg{0.3}O/ZnO quantum well heterostructures were deposited on ZnO nanowires. Strain along the a and c axes of the wurtzite structure is relaxed through the glide of dislocation half-loops from the free surfaces, within pyramidal and prismatic planes. Some half-loops are closed up in the barriers to accommodate the misfit at two consecutive interfaces of the quantum well stack. Dislocations are also observed within the nanowire core: contr…
Ion implantation is an interesting method to dope semiconducting materials such as zinc oxide provided that the implantation-induced defects can be subsequently removed. Nitrogen implantation followed by anneals under O2 were carried out on zinc oxide nanowires in the same conditions as in a previous study on bulk ZnO [J. Appl.Phys. 109, 023513 (2011)], allowing a direct comparison of the defect recovery mechanisms. Transmission electron microscopy and cathodoluminescence were carried out to assess the effects of nitrogen implantation and of subsequent anneals on the structural and optical pro…
We simulated and experimentally investigated the sputter yield of ZnO and GaAs nanowires, which were implanted with energetic Mn ions at room temperature. The resulting thinning of the nanowires and the dopant concentration with increasing Mn ion fluency were measured by accurate scanning electron microscopy (SEM) and nano-X-Ray Fluorescence (nanoXRF) quantification, respectively. We observed a clear enhanced sputter yield for the irradiated nanowires compared to bulk, which is also corroborated by iradina simulations. These show a maximum if the ion range matches the nanowire diameter. As a c…
Our predictions, based on density-functional calculations, reveal that surface doping of ZnO nanowires with Bi leads to a linear-in-$k$ splitting of the conduction-band states, through spin-orbit interaction, due to the lowering of the symmetry in the presence of the dopant. This finding implies that spin polarization of the conduction electrons in Bi-doped ZnO nanowires could be controlled with applied electric (as opposed to magnetic) fields, making them candidate materials for spin-orbitronic applications. Our findings also show that the degree of spin splitting could be tuned by adjusting …
The fracture strength of ZnO nanowires vertically grown on sapphire substrates was measured in tensile and bending experiments. Nanowires with diameters between 60 and 310 nm and a typical length of 2 um were manipulated with an atomic force microscopy tip mounted on a nanomanipulator inside a scanning electron microscope. The fracture strain of (7.7 +- 0.8)% measured in the bending test was found close to the theoretical limit of 10% and revealed a strength about twice as high as in the tensile test. From the tensile experiments the Young's modulus could be measured to be within 30% of that o…
The synthesis, morphology and magneto-transport properties of nanostructure-engineered charge-ordered Pr0.5Ca0.5MnO3 grown on ZnO nanowires are reported. The stability of the charge-ordering can be tuned, but more interestingly the sign of the magnetoresistance is inverted at low temperatures. Coexistence of ferromagnetic clusters on the surface and antiferromagnetic phase in the core of the grains were considered in order to understand these features. This work suggests that such a process of growing on nanowires network can be readily extended to other transition metal oxides and open doors …
We utilize classical molecular dynamics to study surface effects on the piezoelectric properties of ZnO nanowires as calculated under uniaxial loading. An important point to our work is that we have utilized two types of surface treatments, those of charge compensation and surface passivation, to eliminate the polarization divergence that otherwise occurs due to the polar (0001) surfaces of ZnO. In doing so, we find that if appropriate surface treatments are utilized, the elastic modulus and the piezoelectric properties for ZnO nanowires having a variety of axial and surface orientations are a…
We report persistently increased conduction in ZnO nanowires irradiated by ion beam with various ion energies and species. This effect is shown to be related to the already known persistent photo conduction in ZnO and dubbed persistent ion beam induced conduction. Both effects show similar excitation efficiency, decay rates, and chemical sensitivity. Persistent ion beam induced conduction will potentially allow countable (i.e., single dopant) implantation in ZnO nanostructures and other materials showing persistent photo conduction.
Molecular Beam Epitaxy of Al$\mathrm{_{1-x}}$Sc$\mathrm{_{x}}$N Nanowires: Towards Group-III Nitride Piezoelectric Nanogenerators with Enhanced Response
The combination of x-ray spectroscopy methods complemented with theoretical analysis unravels the coexistence of paramagnetic and antiferromagnetic phases in the Zn_0.9Mn_0.1O shell deposited onto array of wurtzite ZnO nanowires. The shell is crystalline with orientation toward the ZnO growth axis, as demonstrated by X-ray linear dichroism. EXAFS analysis confirmed that more than 90% of Mn atoms substituted Zn in the shell while fraction of secondary phases was below 10%. The value of manganese spin magnetic moment was estimated from the Mn Kβ X-ray emission spectroscopy to be 4.3μB which is c…
Metal-oxide nanowires are showing a great interest in the domain of gas sensing due to their large response even at a low temperature, enabling low-power gas sensors. However their response is still not fully understood, and mainly restricted to the linear response regime, which limits the design of appropriate sensors for specific applications. Here we analyse the non-linear response of a sensor based on ZnO nanowires network, both as a function of the device geometry and as a response to oxygen exposure. Using an appropriate model, we disentangle the contribution of the nanowire resistance a…
An emerging branch of electronics, the optospintronics, would be highly boosted if the control of magnetic order by light is implemented in magnetic semiconductors nanostructures being compatible with the actual technology. Here we show that the ferromagnetic magnetization of low Fe-doped ZnO nanowires prepared by carbothermal process is enhanced under illumination up to temperatures slightly below room temperature. This enhancement is related to the existence of an oxygen vacancy V$_{\rm O}$ in the neighbouring of an antiferromagnetic superexchange Fe$^{3+}$-Fe$^{3+}$ pair. Under illumination…
We have studied the electronic structure and the magnetism of Cu-doped ZnO nanowires, which have been reported to show ferromagnetism at room temperature [G. Z. Xing ${et}$ ${al}$., Adv. Mater. {\bf 20}, 3521 (2008).], by x-ray photoemission spectroscopy (XPS), x-ray absorption spectroscopy (XAS) and x-ray magnetic circular dichroism (XMCD). From the XPS and XAS results, we find that the Cu atoms are in the "Cu$^{3+}$" state with mixture of Cu$^{2+}$ in the bulk region ($\sim$ 100 nm), and that "Cu$^{3+}$" ions are dominant in the surface region ($\sim$ 5 nm), i.e., the surface electronic stru…
Current voltage and Kelvin Probe Force Microscopy (KPFM) measurements were performed on single ZnO nanowires. Measurements are shown to be strongly correlated with the contact behavior, either ohmic or Schottky. The ZnO nanowires were obtained by metallo-organic chemical vapor deposition (MOCVD) and contacted using electronic-beam lithography. Depending on the contact geometry, good quality ohmic contacts (linear I V behavior) or non-linear (diode like) Schottky contacts were obtained. Current voltage and KPFM measurements on both types of contacted ZnO nanowires were performed in order to inv…
In this work we have employed density-functional theory with hybrid functionals to investigate the atomic and electronic structure of bare and hydrogenated Co doped ZnO nanowires. We find that in the absence of passivation on the nanowire surface, the cobalt atoms segregate to the surface. On the other hand, under hydrogen passivation, the incorporation of Co is more favorable at inner sites. This suggests that the incorporation of Co in nanostructures has a dependence on the environment and may be facilitated by external atoms and relaxation of the surface.
CdSe quantum dots (QDs) with different organic linker molecules are attached to ZnO nanowires (NWs) to study the luminescence dynamics and the electron tunneling from the QDs to the nanowires in time-resolved photoluminescence (PL) and photoconductivity measurements. The PL transients of the QD luminescence indicate two different recombination channels: the direct recombination inside the QD core and the recombination via QD surface defect states. After linking the QDs to the ZnO NW surface, photo-induced electron tunneling from an excited state of the QD into the conduction band of the nanowi…
Single crystal ZnO nanowires doped with indium are synthesized via the laser-assisted chemical vapor deposition method. The conductivity of the nanowires is measured at low temperatures in magnetic fields both perpendicular and parallel to the wire axes. A quantitative fit of our data is obtained, consistent with the theory of a quasi-one-dimensional metallic system with quantum corrections due to weak localization and electron-electron interactions. The anisotropy of the magneto-conductivity agrees with theory. The two quantum corrections are of approximately equal magnitude with respective t…
As a potential solution for low-cost efficient solar cells, radial junctions consisting of ZnO nanowires arrays embedded in Cu2O thin films have been theoretically modeled. Calculations have been performed to explore the geometric dependence of performance of such wire-based solar cells. By properly setting material properties and cell dimensions, a reasonable power conversion efficiency of 19.7% can be expected in a material with 2 μm minority carrier diffusion length. The detrimental effects of bulk, interface and contact-related states on solar cell performance have also been studied, from …
Nanowire-based light-emitting devices require multi-quantum well heterostructures with high room temperature optical efficiencies. We demonstrate that such efficiencies can be attained through the use of ZnO/Zn(1-x)MgxO core shell quantum well heterostructures grown by metal organic vapour phase epitaxy. Varying the barrier Mg concentration from x=0.15 to x=0.3 leads to the formation of misfit induced dislocations in the multi quantum wells. Correlatively, temperature dependant photoluminescence reveals that the radial well luminescence intensity decreases much less rapidly with increasing tem…
We report the growth of Al-catalysed ZnO nanowires (NWs) using a thermal evaporation technique.Before the growth, the substrates were covered with a distribution of Al nano-island that act as seeds. We found that the density of NWs increases as the density of seeds is increased, confirming the catalyst properties of Al. The critical parameters of growth are the substrate temperature, oxygen partial pressure and the thickness of the initial Al layer from which the seeds are formed. The results showed that the oxygen pressure has a strong influence on the structural characteristics: the nanowire…
We develop an InAs nanowire gate-all-around field-effect transistor using a transparent conductive zinc oxide (ZnO) gate electrode, which is in-situ atomic layer deposited after growth of gate insulator of Al2O3. We perform magneto-transport measurements and find a crossover from weak localization to weak antilocalization effect with increasing gate voltage, which demonstrates that the Rashba spin-orbit coupling is tuned by the gate electrode. The efficiency of the gate tuning of the spin-orbit interaction is higher than those obtained for two-dimensional electron gas, and as high as that for …
The exploration of new catalysts for the vapor-liquid-solid (VLS) synthesis of one-dimensional (1-D) materials promises to yield new morphologies and functionality. Here, we show, for the model ZnO system, that this possible using a semiconductor (Ge) catalyst. In particular, two unusual morphologies are described: twisted nanowires and twisted nanotubes, in addition to the usual straight nanowires. The twisted nanotubes show large hollow cores and surprisingly high twisting rates (up to 9o/μm), which cannot be easily explained through the Eshelby twist model. A combination of ex situ and in s…
The miniaturization of diagnostic devices that exploit optical detection schemes requires the design of light-sources combining small size, high performance for effective excitation of chromophores, and mechanical flexibility for easy coupling to components with complex and non-planar shapes. Here, ZnO nanowire-in-fiber hybrids with internal architectural order are introduced, exhibiting a combination of polarized stimulated emission, low propagation losses of light modes, and structural flexibility. Ultrafast transient absorption experiments on the electrospun material show optical gain which…
