arXiv 0801.12672008-01-08physics.optics

Surface plasmon polariton modes in a single-crystal Au nanoresonator fabricated using focused-ion-beam milling

E. J. R. Vesseur, R. de Waele, A. Polman, H. J. Lezec, H. A. Atwater, F. J. García de Abajo

备注：: 4 pages, 4 figures
DOI：: 10.1063/1.2885344

英文摘要：

We use focused-ion-beam milling of a single-crystal Au surface to fabricate a 590-nm-long linear ridge that acts as a surface plasmon nanoresonator. Cathodoluminescence imaging spectroscopy is then used to excite and image surface plasmons on the ridge. Principal component analysis reveals distinct plasmonic modes, which proves confinement of surface-plasmon oscillations to the ridge. Boundary-element-method calculations confirm that a linear ridge is able to support highly-localized surface-plasmon modes (mode diameter < 100 nm). The results demonstrate that focused-ion-beam milling can be used in rapid prototyping of nanoscale single-crystal plasmonic components.

机构、总结、中文摘要均由AI分析而来，可能存在错误，请以论文正文为准。

阅读原文

阅读 PDF ↗

arXiv 页面 ↗HTML 原文 ↗

本文内容

英文摘要相关论文

机构、总结、中文摘要均由AI分析而来，可能存在错误，请以论文正文为准。

继续探索

相关论文

Microscopic diamond Solid-Immersion-Lenses fabricated around single defect ceneters by focussed ion beam milling

Recent efforts to define microscopic solid-immersion-lenses (SIL) by focused ion beam milling into diamond substrates that are registered to a preselected single photon emitter are summarized. We show how we determine the position of a single emitter with at least 100 nm lateral and 500 nm axial accuracy, and how the milling procedure is optimized. The characteristics of a single emitter, a Nitrogen Vacancy (NV) center in diamond, are measured before and after producing the SIL and compared with each other. A count rate of 1.0 million counts per second is achieved with a $[111]$ oriented NV ce…

2014-10-10cond-mat.mtrl-sciphysics.opticsquant-ph

Effects of Ga+ milling on InGaAsP Quantum Well Laser with mirrors etched by Focused Ion Beam

InGaAsP/InP quantum wells (QW) ridge waveguide lasers were fabricated for the evaluation of Ga+ Focused Ion Beam (FIB) milling of mirrors. Electrical and optical proprieties were investigated. A 7% increment in threshold current, a 17% reduction in external quantum efficiency and 15 nm blue shift in the emission spectrum were observed after milling as compared to the as cleaved facet result. Annealing in inert atmosphere partially revert these effects resulting in 4% increment in threshold current, 11% reduction in external efficiency and 13 nm blue shift with the as cleaved result. The curren…

2009-04-06physics.optics

Micromanufacturing of geometrically- and dimensionally-precise molecular single-crystal photonic micro-resonators via focused ion beam milling

Highly reproducible manufacturing of organic optical crystals with well-defined geometry and dimension is important to realize industrially relevant all-organic microelectronic and nanophotonic components, and photonic integrated circuits. Here, we demonstrate programmed shape and size alteration of perylene crystal resonators into disk and rectangular geometries using focused-ion beam milling technique. Due to highly reproducible nature of the employed technique, the fabricated smaller sized disk and rectangular crystal resonators displaying shape and size dependent optical modes are suitable…

2022-03-27cond-mat.mtrl-sciphysics.optics

Nanostructuring Optical Waveguides by Focused Ion Beam Milling. Near-Field Characterization

Nanostructures have become an attractive subject due to many applications, particularly the photonic bandgap effect observed in photonic crystals. Nevertheless, the fabrication of such structures remains a challenge because of accurate requirement concerning regularity, shape, hole depth etc. of the structure. E-beam lithography permits a good control of dimensional parameters but needs a 1-step fabrication process. In our work, we have to combine traditional strip-load waveguides (SiO2/SiON/SiO2 on Si) and nanostructures whose dimension are totally different. This imposes a 2-step process whe…

2008-01-26physics.optics

通过结合FIB铣削和CO$_2$激光烧蚀制造定制化、低损耗光学谐振器

Fabrication of Customized, Low-Loss Optical Resonators by Combination of FIB-Milling and CO$_2$ Laser Ablation

该研究提出一种结合FIB铣削与CO$_2$激光平滑的新技术，用于制造定制化、低损耗的法布里-珀罗腔镜，实现纳米级精度和亚纳米表面粗糙度。

2025-04-22physics.opticsquant-ph

Monolithic integration of a high-quality factor lithium niobate microresonator with a free-standing membrane waveguide using femtosecond laser assisted ion beam writing (FLAIBW)

We demonstrate integrating a high quality factor lithium niobate microdisk resonator with a free-standing membrane waveguide. Our technique is based on femtosecond laser direct writing which produces the pre-structure, followed by focused ion beam milling which reduces the surface roughness of sidewall of the fabricated structure to nanometer scale. Efficient light coupling between the integrated waveguide and microdisk was achieved, and the quality factor of the microresonator was measured as high as 1.67*10^5.

2017-01-19physics.optics

更多相关论文收起更多论文

Induced Optical Losses in Optoelectronic Devices due to Focused Ion Beam Damages

A study of damages caused by gallium focused ion beam (FIB) into III-V compounds is presented. Potential damages caused by local heating, ion implantation, and selective sputtering are presented. Preliminary analysis shows that local heating is negligible. Gallium implantation is shown to occur over areas tens of nanometers thick. Gallium accumulation as well as selective sputtering during III-V compounds milling is expected. Particularly, for GaAs, this effect leads to gallium segregation and formation of metallic clusters. Microdisk resonators were fabricated using FIB milling with different…

2012-07-10cond-mat.mtrl-sciphysics.optics

Propagation of plasmons in designed single crystalline silver nanostructures

We demonstrate propagation of plasmons in single crystalline silver nanostructures fabricated using a combination of a bottom-up and a top-down approach. Silver nanoplates of thickness around 65 nm and a surface area of about 100 μm^2 are made using a wet chemical method. Silver nanotips and nanowires are then sculptured by focused ion beam milling. The plasmons are excited by using the fluorescence from the redeposited silver clusters during the milling process. Propagation of plasmons in the nanowires is observed in the visible spectral region. We also observe a cavity effect by measuring th…

2013-06-19cond-mat.mes-hallphysics.opticsquant-ph

A low cost plasmonic platform for photon emission engineering of two dimensional semiconductors

Although the field of 2D materials has democratized materials science by making high quality samples accessible cheaply, due to the atomically thin nature of these systems, an integration with nanostructures is almost always required to obtain a significant optical response. Traditionally, these nanostructures are fabricated via electron beam lithography or focused ion beam milling, which are expensive and large area fabrication can be further time consuming. In order to overcome this problem, we report the integration of 2D semiconductors on a cost-effective and large area fabricated nanocone…

2022-03-22cond-mat.mes-hallphysics.optics

Interferometric near-field characterization of plasmonic slot waveguides in single- and poly-crystalline gold films

Plasmonic waveguides are a promising platform for integrated nanophotonic circuits and nanoscale quantum optics. Their use is however often hampered by the limited propagation length of the guided surface plasmon modes. A detailed understanding of the influence of the material quality and the waveguide geometry on the complex mode index is therefore crucial. In this letter, we present interferometric near-field measurements at telecommunication wavelength on plasmonic slot waveguides fabricated by focused ion beam milling in single- and poly-crystalline gold films. We observe a significantly b…

2019-07-15physics.optics

六方氮化硼中碳辅助聚焦离子束工程实现确定性单光子发射体阵列

Deterministic Single-Photon Emitter Arrays in Hexagonal Boron Nitride by Carbon-Assisted Focused Ion Beam Engineering

Indian Institute of Technology Bombay（印度理工学院孟买分校）

提出一种无光刻的三步工艺（镓离子束刻蚀、纳米碳沉积、热退火）在六方氮化硼中生成空间可控的单光子发射体阵列，发射体产率达89%，最佳发射体纯度g^(2)(0)=0.15±0.09，为集成量子光子学提供可扩展路径。

2026-06-11cond-mat.mes-hallphysics.optics

Electron energy-loss spectroscopy on freestanding perforated gold films

We report on a combined far- and near-field study of surface plasmon polaritons on freestanding perforated gold films. The samples are fabricated by focused ion beam milling of {a periodic hole array into} a carbon membrane followed by thermal evaporation of gold and plasma ashing of the carbon film. Optical transmission spectra show a series of characteristic features, which can be attributed to the excitation of surface plasmon modes via the periodic nanohole array. The corresponding near-field distributions are mapped by electron energy-loss spectroscopy. Besides the optically bright surfac…

2021-01-06cond-mat.mtrl-sciphysics.optics

The effects of ion implantation damage to photonic crystal optomechanical resonators in silicon

Optomechanical resonators were fabricated on a silicon-on-insulator (SOI) substrate that had been implanted with phosphorus donors. The resonators' mechanical and optical properties were then measured (at 6 kelvin and room temperature) before and after the substrate was annealed. All measured resonators survived the annealing and their mechanical linewidths decreased while their optical and mechanical frequencies increased. This is consistent with crystal lattice damage from the ion implantation causing the optical and mechanical properties to degrade and then subsequently being repaired by th…

2021-09-28cond-mat.mes-hallcond-mat.mtrl-sciphysics.optics