arXivDaily arXiv每日学术速递 周一至周五更新
arXiv周末暂无论文更新,休息一下吧,周末愉快~~
arXiv 2602.00304astro-ph.IM
收藏

3D打印氧化铝作为毫米波光学元件

3D Printed Alumina as a Millimeter-Wave Optical Element

School of Physics and Astronomy, University of Minnesota(明尼苏达大学物理与天文学院);Kavli Institute for the Physics and Mathematics of the Universe (IPMU), The University of Tokyo(东京大学宇宙物质研究宇宙线前沿国际中心);Laser Zentrum Hannover e.V.(汉诺威激光中心);Institute for Photon Science and Technology (IPST), The University of Tokyo(东京大学光子科学技术研究所)
Rex Lam, Scott Cray, Sam Dietterich, Calvin Firth, Shaul Hanany, Takumi Izawa, Jürgen Koch, Kuniaki Konishi, Tomotake Matsumura, Haruyuki Sakurai, Yuki Sakurai,… 展开作者

Rex Lam, Scott Cray, Sam Dietterich, Calvin Firth, Shaul Hanany, Takumi Izawa, Jürgen Koch, Kuniaki Konishi, Tomotake Matsumura, Haruyuki Sakurai, Yuki Sakurai, Ryota Takaku, Andrew Yan

AI总结:

研究通过3D打印氧化铝制作毫米波光学元件,验证其折射率、损耗及抗反射性能,为天体物理应用提供新可能。

摘要:

我们展示了3D打印的氧化铝盘以及带有单面3D打印亚波长结构抗反射涂层(SWS-ARC)的盘在毫米和亚毫米波段室温下的传输和损耗测量。对于覆盖158-700GHz的四个频段,我们发现折射率一致为n=3.107±0.007。在整个158GHz至700GHz频率范围内,损耗跨度为1×10⁻³≤tanδ≤2.49×10⁻³,低频范围的不确定率为10%-30%,而在高频范围缩小至约2%。正如预期的那样,与平坦盘数据中明显的构造和破坏性干涉条纹不同,带有SWS-ARC的盘中这些条纹消失。测量数据与基于SWS测量形状的有限元分析预测一致。在158GHz至200GHz频率范围内,低于衍射效应起始点,反射率从最大64%降低到约25%,与预测非常接近。这些3D打印氧化铝的折射率、损耗和SWS-ARC测量结果表明,该材料和制造技术可能对天体物理应用有用。

英文摘要:

We present millimeter and sub-millimeter room temperature transmission and loss measurements of 3D printed alumina disc and of a disc with one-sided 3D printed sub-wavelength structures anti-reflection coatings (SWS-ARC). For four bands spanning 158 - 700~GHz we find an index of refraction consistent with $n= 3.107 \pm 0.007$. The loss over the entire frequency band between 158~GHz and 700~GHz spans $ 1 \cdot 10^{-3} \leq \tan δ\leq 2.49 \cdot 10^{-3}$ with 10%-30% uncertainty at the lower range of frequencies shrinking to $\sim\!2\%$ at the higher frequencies. As expected, constructive and destructive interference fringes that are apparent with the flat disc data are absent with the disc that has SWS-ARC. The measured data are consistent with finite element analysis predictions that are based on the measured shape of the SWS. At frequencies between 158~GHz and 200~GHz, below the onset of diffraction effects, reflectance is reduced from a maximum of 64% to about 25%, closely matching predictions. These measurements of the index, loss, and SWS-ARC of 3D printed alumina suggest that the material and fabrication technique could be useful for astrophysical applications.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑