arXivDaily arXiv每日学术速递 周一至周五更新
arXiv 2408.15024physics.flu-dyn
收藏

Glacierware:利用拓扑优化实现面向高TDP芯片的热点感知微流控冷却

Glacierware: Hotspot-aware Microfluidic Cooling for High TDP Chips using Topology Optimization

Athanasios Boutsikakis, Emile Soutter, Miguel A. Salazar de Troya, Nicola Esposito, Dasha Mukasheva, Hanane Bouras, Remco van Erp

AI总结:

本文提出Glacierware平台,利用拓扑优化设计热点感知微流控冷却,针对高TDP芯片,相比最优直通道降低13%温升或55%压降。

摘要:

GPU计算能力的持续提升,对于人工智能和数据处理等领域的发展至关重要,这也推动了数据中心采用液体冷却技术。采用平行直通道的铲削铜冷板是一种成熟的技术,但由于制造限制,其设计自由度有限。随着芯片设计日益复杂并转向异构集成,这些平行直通道无法应对芯片上集中高热通量区域(热点)的关键问题。单个热点超过温度上限可能导致整个芯片降频,从而限制性能。此外,这还要求降低数据中心冷却液的入口温度,导致电力和水消耗增加。理想情况下,冷板与芯片热点接触的区域需要更小的通道以增强对流换热,而低热通量区域则可采用更大的通道以补偿增加的压降。然而,由于问题的非线性,手动优化这种冷却设计颇具挑战。本文中,我们探索使用拓扑优化作为一种方法,根据芯片的功率分布定制微流控冷却设计,以解决高功率芯片中的热点温度问题,并使用名为Glacierware的平台。我们将热点感知的拓扑优化微流控设计与不同宽度的直通道进行对比,以评估其性能。评估结果表明,与性能最佳的直通道相比,该优化设计的温升降低13%或压降降低55%,表明在压力和流量均受限的工业应用中具有高度竞争力。

英文摘要:

The continuous increase in computational power of GPUs, essential for advancements in areas like artificial intelligence and data processing, is driving the adoption of liquid cooling in data centers. Skived copper cold plates featuring parallel straight channels are a mature technology, but they lack design freedom due to manufacturing limitations. As chips become increasingly complex in their design with the transition towards heterogeneous integration, these parallel straight channels are not able to address critical areas of concentrated high heat flux (hotspots) on a chip. A single hotspot exceeding the upper temperature limit can cause the full chip to throttle and hence limit performance. In addition, this would require a reduction in coolant inlet temperature in the data center, causing an increase in electricity and water consumption. Ideally, areas of the cold plate in contact with hotspots of the chip need smaller channels to increase convective heat transfer, whereas areas with low heat flux may benefit from larger channels to compensate for the increased pressure drop. However, manual optimization of such a cooling design is challenging due to the nonlinearity of the problem. In this paper, we explore the usage of topology optimization as a method to tailor microfluidic cooling design to the power distribution of a chip to address the hotspot temperatures in high-power chips, using a platform called Glacierware. We compare the hotspot-aware, topology-optimized microfluidic design to straight channels of various widths to benchmark its performance. Evaluations of this optimized design show a 13% lower temperature rise or a 55% lower pressure than the best-performing straight channels, indicating highly competitive performance in industrial settings where both pressure and flow rate are constrained.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑