面向LEO卫星的即插即用阻力帆模块:AirDragMod (ADM)的实现与早期测试
Plug-and-Play Drag Sail Module for LEO Satellites: Implementation and Early Testing of AirDragMod (ADM)
AI总结:
针对LEO卫星碎片离轨难题,本文提出了一种基于COTS组件的即插即用阻力帆模块AirDragMod,通过被动离轨与主动控制结合,并经原型测试与仿真验证了其低成本可行性。
摘要:
空间碎片已成为关键问题,轨道上的碎片数量已超过活跃卫星,对太空可持续性构成重大风险。在LEO中,任务结束后被丢弃且无轨道控制的有效载荷或火箭主体是主要来源。IADC指南建议将受保护区域内的任务后驻留时间限制在25年。FCC最近出台了更严格的规定,将LEO卫星允许的任务后停留时间缩短至5年。这些变化要求将离轨系统纳入卫星设计。然而,由于LEO卫星的质量和体积限制,特别是对于大型星座或CubeSats,增加额外燃料和发动机进行主动离轨面临挑战。这通常导致优先考虑任务关键组件而非离轨系统。因此,人们开始探索被动离轨技术或国际法规等替代方案。阻力帆是针对中小型LEO卫星的一种高性价比被动解决方案。本文提出了一种即插即用阻力帆模块,采用COTS组件,适用于CubeSats和亚质量卫星。可扩展设计源自任务需求和轨迹分析。该技术包含主动控制,以在特定轨道LTAN下实现更快离轨。受JAXA的IKAROS任务启发,部署机制利用残余角动量并遵循标准序列。成本分析估算了系统的盈亏平衡点。对配备3D打印部署系统和倒置步进电机的原型机进行了测试,并与数值模型进行了对比。利用测试数据的曲线拟合,开发了帆伸展花瓣的张力模型。SIMULINK多体模型可用于仿真。仍需进一步的实验和原型开发来评估真实世界性能,其中控制系统被认定为至关重要。
英文摘要:
Space debris has become a critical issue, with debris in orbit surpassing active satellites, posing significant risks to space sustainability. Payloads or rocket bodies discarded post-mission in LEO without orbital control are major sources. The IADC guidelines recommend limiting post-mission presence in protected regions to 25 years. The FCC recently introduced stricter regulations, reducing the allowable post-mission stay for LEO satellites to 5 years. These changes necessitate integrating deorbiting systems into satellite designs. However, adding extra fuel and engines for active deorbiting presents challenges due to LEO satellites' mass and volume limitations, especially for large constellations or CubeSats. This often leads to prioritizing mission-critical components over deorbiting systems. Thus, alternative approaches like passive deorbiting techniques or international regulations are explored. Drag sails are a cost-effective passive solution for small and medium-sized LEO satellites. This paper proposes a plug-and-play drag sail module using COTS components for CubeSats and sub-mass satellites. The scalable design is derived from mission requirements and trajectory analysis. The technique includes active control for quicker deorbiting at specific orbital LTAN. Inspired by JAXA's IKAROS mission, the deployment mechanism uses residual angular momentum and follows a standard sequence. A cost analysis estimates the system's breakeven point. A prototype with a 3D-printed deployment system and inverted stepper motor was tested and compared to a numerical model. A tension model for sail extension petals was developed using curve fitting from test data. SIMULINK multibody models are available for simulations. Further experimentation and prototype development are required to assess real-world performance, with a control system identified as crucial.
机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。