在0.11-μm体硅和22-nm FD-SOI中利用正向体偏置实现的nA级、面积高效、低于100-ppm/°C的峰值电流基准
A nA-Range Area-Efficient Sub-100-ppm/°C Peaking Current Reference Using Forward Body Biasing in 0.11-$μ$m Bulk and 22-nm FD-SOI
AI总结:
本文提出基于弱反型阈值电压差和正向体偏置的nA级CWT峰值电流基准,在0.11-μm体硅与22-nm FD-SOI中验证,显著减小面积并改善温度系数。
摘要:
近年来,物联网(IoT)的发展推动了对nA级电流基准的需求,这类基准同时受到小面积限制,并且必须对工艺、电压和温度变化具有鲁棒性。然而,此类基准仍难以实现,因为现有架构无法在最小化硅面积的同时达到较低的温度系数(TC)。本文提出一种nA级温度恒定(CWT)峰值电流基准,其中电阻由两个处于弱反型区的晶体管之间的阈值电压差进行偏置。该偏置电压低于传统架构,以减少电阻占用的硅面积;其实现方式是利用一个超低功耗电压基准对两个晶体管之一施加正向体偏置,从而降低其阈值电压。此外,所提出的基准包含一个用于抑制高温下寄生二极管泄漏的电路,以及用于基准电流及其TC的两种简单修调机制。由于该设计依赖体效应,因此在0.11-μm体硅和22-nm全耗尽绝缘体上硅(fully-depleted silicon-on-insulator)两种工艺中均进行了验证,以证明其在不同技术类型中的可行性。在版图后仿真中,0.11-μm设计产生5-nA电流,TC为65 ppm/°C,线性灵敏度(LS)为2.84 %/V;而在测量中,22-nm设计实现1.5-nA电流,TC为89 ppm/°C,LS为0.51 %/V。得益于较低的电阻偏置电压,所提出的基准在0.11 μm工艺中占用0.00954 mm²硅面积(在22 nm工艺中为0.00214 mm²),比已流片的nA级CWT基准至少小1.8倍(分别为8.2倍),同时TC改善6.1倍(分别为4.4倍)。
英文摘要:
In recent years, the development of the Internet of Things (IoT) has prompted the search for nA-range current references that are simultaneously constrained to a small area and robust to process, voltage and temperature variations. Yet, such references have remained elusive, as existing architectures fail to reach a low temperature coefficient (TC) while minimizing silicon area. In this work, we propose a nA-range constant-with-temperature (CWT) peaking current reference, in which a resistor is biased by the threshold voltage difference between two transistors in weak inversion. This bias voltage is lower than in conventional architectures to cut down the silicon area occupied by the resistor and is obtained by forward body biasing one of the two transistors with an ultra-low-power voltage reference so as to reduce its threshold voltage. In addition, the proposed reference includes a circuit to suppress the leakage of parasitic diodes at high temperature, and two simple trimming mechanisms for the reference current and its TC. As the proposed design relies on the body effect, it has been validated in both 0.11-$μ$m bulk and 22-nm fully-depleted silicon-on-insulator, to demonstrate feasibility across different technology types. In post-layout simulation, the 0.11-$μ$m design generates a 5-nA current with a 65-ppm/°C TC and a 2.84-%/V line sensitivity (LS), while in measurement, the 22-nm design achieves a 1.5-nA current with an 89-ppm/°C TC and a 0.51-%/V LS. As a result of the low resistor bias voltage, the proposed references occupy a silicon area of 0.00954 mm$^2$ in 0.11 $μ$m (resp. 0.00214 mm$^2$ in 22 nm) at least 1.8$\times$ (resp. 8.2$\times$) smaller than fabricated nA-range CWT references, but with a TC improved by 6.1$\times$ (resp. 4.4$\times$).
机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。