arXivDaily arXiv每日学术速递 周一至周五更新
arXiv 2404.03580physics.ins-dethep-ex
收藏

用于SoLid实验的CCube重建算法

The CCube reconstruction algorithm for the SoLid experiment

Université Clermont Auvergne, CNRS/IN2P3, LPCA(克莱蒙奥弗涅大学);University of Bristol(布里斯托大学);Normandie Univ, ENSICAEN, UNICAEN, CNRS/IN2P3, LPC Caen(诺曼底大学,恩西肯高等学院,卡昂大学);CERN(欧洲核子研究组织);Imperial College London(帝国理工学院);SUBATECH, Nantes Université, IMT Atlantique, CNRS/IN2P3(南特大学);IJCLab, Univ Paris-Sud, CNRS/IN2P3, Université Paris-Saclay(巴黎第十一大学);University of Oxford(牛津大学);SCK-CEN, Belgian Nuclear Research Centre(比利时核研究中心);STFC, Rutherford Appleton Laboratory, Harwell Oxford, and Daresbury Laboratory(英国科学与技术设施委员会)

The SoLid collaboration

AI总结:

针对SoLid极短基线反中微子振荡实验的高度分段探测器,本文设计了CCube重建算法以将光纤读出信号转换为探测单元列表,对比三种方法后选定了实验基线方案。

摘要:

SoLid实验是一项极短基线实验,旨在搜寻核反应堆产生的有源反中微子到惰性反中微子的振荡现象。其探测原理基于两种固体闪烁体的配对使用:聚乙烯基甲苯与$^6$LiF:ZnS(Ag),这是该物理领域应用的一项新技术。除了具备良好的中子-伽马甄别能力外,这种装置还能实现探测器的高度分段(基本探测单元为边长5厘米的立方体)。高度分段带来诸多优势,包括反β衰变(IBD)产物的精确定位、可靠的反中微子能量估计量的推导,以及基于信号拓扑特征的强大本底抑制工具。最后,该系统通过耦合到光电探测器(MPPC)的波长位移光纤网络进行读出。本文介绍了可最大化利用探测器粒度的重建算法设计。该算法的目标是将光纤读出的输出转换为产生信号的探测单元列表。本文对三种方法进行了性能比较,并最终选定了该实验的基线方法。

英文摘要:

The SoLid experiment is a very-short-baseline experiment aimed at searching for nuclear reactor-produced active to sterile antineutrino oscillations. The detection principle is based on the pairing of two types of solid scintillators: polyvinyl toluene and $^6$LiF:ZnS(Ag), which is a new technology used in this field of Physics. In addition to good neutron-gamma discrimination, this setup allows the detector to be highly segmented (the basic detection unit is a 5 cm side cube). High segmentation provides numerous advantages, including the precise location of Inverse Beta Decay (IBD) products, the derivation of the considerate antineutrino energy estimator, and a powerful background reduction tool based on the topological signature of the signal. Finally, the system is read out by a network of wavelength-shifting fibres coupled to a photodetector (MPPC). This paper describes the design of the reconstruction algorithm that allows maximum use of the granularity of the detector. The goal of the algorithm is to convert the output of the optical-fibre readout to the list of the detection units from which it originated. This paper provides a performance comparison for three methods and concludes with a choice of the baseline approach for the experiment.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑