arXivDaily arXiv每日学术速递 周一至周五更新
arXiv周末暂无论文更新,休息一下吧,周末愉快~~
arXiv 2303.09094q-bio.TO
收藏

牛心包密度的测量及其对生物心脏瓣膜瓣叶应力分布的影响

The measurement of bovine pericardium density and its implications on leaflet stress distribution in bioprosthetic heart valves

Masod Sadipour, Ali N. Azadani

AI总结:

本研究测量生物心脏瓣膜所用牛心包密度,并通过有限元模型分析其对瓣叶应力与变形的影响,证明采用准确密度对可靠计算建模至关重要。

摘要:

目的:生物心脏瓣膜(Bioprosthetic Heart Valves,BHVs)目前得到广泛应用,并取得了良好效果。计算建模为在临床前阶段定量描述BHVs提供了一个框架。为了在计算建模中获得可靠解,必须考虑准确的瓣叶属性,例如力学性能和密度。牛心包(Bovine pericardium,BP)被广泛用作BHV瓣叶材料。既往计算研究假设BP密度接近水或血液的密度。然而,BP瓣叶会经历固定和抗钙化等多种处理。本研究旨在测量BHVs中所用BP的密度,并确定其对瓣叶应力分布的影响。方法:我们测定了从Edwards BP补片上激光切割得到的8个方形BP样品的密度。使用A&D分析天平测量试样重量,并通过高分辨率成像测量体积。在ABAQUS中建立了类似于PERIMOUNT Magna的BHV有限元模型。结果:BP样品的平均密度值为1410 kg/m3。在心动周期的加速阶段,密度为1410 kg/m3时最大应力值达到1.89 MPa,而密度为1000 kg/m3时为2.47 MPa(相差30.7%)。在减速阶段,最大应力值分别达到713 kPa和669 kPa。结论:BHV瓣叶的应力分布和变形取决于密度大小。确定BHV瓣叶密度的准确值对于计算模型至关重要。

英文摘要:

Purpose: Bioprosthetic Heart Valves (BHVs) are currently in widespread use with promising outcomes. Computational modeling provides a framework for quantitatively describing BHVs in the preclinical phase. To obtain reliable solutions in computational modeling, it is essential to consider accurate leaflet properties such as mechanical properties and density. Bovine pericardium (BP) is widely used as BHV leaflets. Previous computational studies assume BP density to be close to the density of water or blood. However, BP leaflets undergo multiple treatments such as fixation and anti-calcification. The present study aims to measure the density of the BP used in BHVs and determine its effect on leaflet stress distribution. Methods: We determined the density of eight square BP samples laser cut from Edwards BP patches. The weight of specimens was measured using an A&D Analytical Balance, and volume was measured by high-resolution imaging. Finite element models of a BHV similar to PERIMOUNT Magna were developed in ABAQUS. Results: The average density value of the BP samples was 1410 kg/m3. In the acceleration phase of a cardiac cycle, the maximum stress value reached 1.89 MPa for a density value of 1410 kg/m3 , and 2.47 MPa for a density of 1000 kg/m3(30.7% difference). In the deceleration, the maximum stress value reached 713 and 669 kPa, respectively. Conclusion: Stress distribution and deformation of BHV leaflets are dependent upon the magnitude of density. Ascertaining an accurate value for the density of BHV leaflets is essential for computational models.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑