利用3D打印泡沫状传感器的软质鞋垫估计三维地面反作用力
Soft insoles for estimating 3D ground reaction forces using 3D printed foam-like sensors
AI总结:
本文研究用四个3D打印软质泡沫状传感器结合Hammerstein-Wiener系统辨识模型估计三维地面反作用力,在九名参与者上取得优于或可比商用FSR的性能,验证了该方案在轻便、定制化可穿戴力传感应用中的可行性。
摘要:
集成传感器的鞋垫为日常生活中的步态研究和健康监测提供了一种工具。为了让用户接受这类鞋垫,它们需要舒适且轻便。以往的工作已经证明,利用鞋垫估计地面反作用力(GRFs)是可行的。然而,这些鞋垫通常由商用组件组装而成,限制了设计自由度和定制化。在本工作中,我们研究了使用四个3D打印的软质泡沫状传感器来使鞋垫具备传感功能。这些传感器与Hammerstein-Wiener模型的系统辨识相结合,用于估计三维GRFs,并与作为金标准的仪器化跑步机测得的值进行比较。观察到这四个传感器在步态周期中的表现与预期的压力分布变化一致。此外,辨识得到的(个性化)Hammerstein-Wiener模型在垂直、内外侧和前后方向的GRFs上表现出最佳的估计性能(平均RMS误差为9.3%,R^2=0.85,平均绝对误差(MAE)为7%)。这表明这些传感器能够相当合理地估计合成的三维力。九名参与者的这些结果与使用商用FSR和机器学习的其他工作相比具有可比性或更优。辨识得到的模型估计性能随时间有所下降,但一周后平均保持在11.35% RMS和8.6% MAE,且Hammerstein-Wiener模型在第二天到第七天之间表现似乎保持一致。这些结果表明,将3D打印的软质压阻泡沫状传感器与系统辨识相结合,对于需要柔软性、轻量化和定制化的应用(如可穿戴(力)传感器)是一种可行的方法。
英文摘要:
Sensorized insoles provide a tool for gait studies and health monitoring during daily life. For users to accept such insoles they need to be comfortable and lightweight. Previous work has already demonstrated that estimation of ground reaction forces (GRFs) is possible with insoles. However, these are often assemblies of commercial components restricting design freedom and customization. Within this work, we investigate using four 3D-printed soft foam-like sensors to sensorize an insole. These sensors were combined with system identification of Hammerstein-Wiener models to estimate the 3D GRFs, which were compared to values from an instrumented treadmill as the golden standard. It was observed that the four sensors behaved in line with the expected change in pressure distribution during the gait cycle. In addition, the identified (personalized) Hammerstein-Wiener models showed the best estimation performance (on average RMS error 9.3%, R^2=0.85 and mean absolute error (MAE) 7%) of the vertical, mediolateral, and anteroposterior GRFs. Thereby showing that these sensors can estimate the resulting 3D force reasonably well. These results for nine participants were comparable to or outperformed other works that used commercial FSRs with machine learning. The identified models did decrease in estimation performance over time but stayed on average 11.35% RMS and 8.6% MAE after a week with the Hammerstein-Wiener model seeming consistent between days two and seven. These results show promise for using 3D-printed soft piezoresistive foam-like sensors with system identification to be a viable approach for applications that require softness, lightweight, and customization such as wearable (force) sensors.
机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。