arXivDaily arXiv每日学术速递 周一至周五更新
arXiv周末暂无论文更新,休息一下吧,周末愉快~~
arXiv 2204.09999cond-mat.mtrl-sci
收藏

铁基金属基复合材料:现状、范围与挑战

Ferrous Metal Matrix Composites Status Scope and Challenges

Amarjit Singh, Jarnail Singh, Manoj Kumar Sinha, Ravi Kumar

AI总结:

本文总结了铁基金属基复合材料的现状、范围与挑战,指出其研究少于有色金属基复合材料,并强调用工业废料替代昂贵增强材料以降低成本,同时展望其作为 NFMMCs 有力竞争者的前景。

摘要:

本文旨在总结铁基金属基复合材料(FMMCs)的发展现状、应用范围及面临的挑战。与有色金属基复合材料(NFMMCs)相比,FMMCs 历史悠久,但在文献和实际应用中的使用较少。因此,这促使我们探索 FMMCs 文献和现场应用稀缺背后的原因,并需进行科学研究。粉末冶金工艺是制造铁基和钢基 FMMCs 最常用的方法,通过增强颗粒来实现。同时,原位方法已被用于制造铸铁基 FMMCs。在设计和制造 FMMCs 时考虑的主要特性是耐磨性和改善的比力学性能。为了制造更便宜且环保的 FMMCs,传统上使用的高成本增强材料(如 SiC、WC、TiC、SiO2、TiO2、TiB2)需要用廉价的工业废料(如赤泥、粉煤灰和磨削屑)来替代。从 Web of Science 提取的数据表明,FMMCs 的研究少于 NFMMCs。关于 FMMCs 的研究论文数量不断增加,预示着光明的前景。FMMCs 将成为研究人员和制造商的热门话题。更高的强度、耐磨性、高温下的尺寸稳定性,以及最重要的是更低的成本,将使 FMMCs 成为 NFMMCs 的有力竞争者。在 FMMCs 的开发和批量生产用于现场应用时,氧化和重量更重等挑战仍需特别的研究努力。

英文摘要:

The present paper is an effort to culminate the status, scopes and challenges in the development of ferrous metal matrix composites (FMMCs). The FMMCs are old but less in use than the non-ferrous metal matrix composites (NFMMCs), as far as literature and actual applications are concerned. Therefore, this stimulates the exploration of the reasons behind the scarcity of literature and field applications of the FMMCs, which must be investigated scientifically. The powder metallurgy route is the most used process for fabricating iron and steel based FMMCs by reinforcing particulates. At the same time, the in-situ method has been used for the fabrication and cast iron-based FMMCs. The main characteristics being considered during the designing and fabrication of FMMCs are wear resistance and improved specific mechanical properties. To fabricate cheaper and eco-friendly FMMCs, traditionally used costly reinforcements such as SiC, WC, TiC, SiO2, TiO2, TiB2 are required to be replaced by inexpensive industrial wastes like red-mud, fly-ashes and grinding swarf. The data extracted from the web of science exhibited that the FMMCs have been researched less than the NFMMCs. The increasing number of research papers on FMMCs indicates a bright future. FMMCs are going to be a favourite topic among researchers and manufacturers. Higher strengths, wear resistance, dimensional stability at elevated temperatures, and, most importantly, the lower cost will put forward the FMMCs as a stiff competitor of NFMMCs. In developing and mass production of FMMCs for field applications, challenges like oxidation and higher weight still require special research efforts.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑