磁共振成像原位研究聚合物多孔膜的润湿模式
In-situ investigation of wetting patterns in polymeric multibore membranes via magnetic resonance imaging
摘要:
润湿膜以置换空气或调节液体对于利用过滤膜的复杂孔隙率是重要的。这项研究揭示了多孔膜过滤模块中润湿的细节。使用磁共振成像(MRI),我们量化了在死端渗透模式下初始膜润湿过程中的流体分布模式。硫酸铜水溶液润湿膜纤维的时空演变作为施加的通量,填充密度,和沿膜组件长度的位置的函数进行了研究。三个初始润湿条件进行了检查:交付状态的膜,乙醇清洗和干燥(空气填充)的膜,和乙醇填充的膜。由于界面和聚合物溶胀效应,观察到润湿图案的显着变化。这种原位研究揭示了缓慢的润湿过程超过六个小时或更长时间,以获得完全润湿,即使在200 LMH的高通量。然而,增加的通量导致更快的润湿动力学,因为逐渐形成的润湿图案是通量依赖的。多孔纤维的填充密度通过改变主要的压力条件而另外影响润湿动力学。尽管在死端模式下,润湿进展沿着膜组件长度是不均匀的。在此基础上,深入研究了不同预润湿剂对驱替性能的影响。这项研究有助于理解(a)在死端过滤中多孔膜内部的复杂润湿现象,(b)由于相邻膜,膜与周围环境的相互作用,以及(c)用于置换的流体系统对所得润湿图案的影响。
英文摘要:
Wetting of the membrane to displace air or conditioning liquids is important to exploit the complex porosity of a filtration membrane. This study reveals the details of wetting in multibore membrane-based filtration modules. Using magnetic resonance imaging (MRI), we quantify the fluid distribution patterns during initial membrane wetting in dead-end permeation mode. The spatio-temporal evolution of aqueous copper sulfate solution wetting the membrane fibers was investigated as a function of the applied flux, packing density, and position along the membrane module length. Three initial wetting conditions were examined: delivery-state membranes, ethanol-washed and dried (air-filled) membranes, and ethanol-filled membranes. Significant changes in wetting patterns were observed due to interfacial and polymer swelling effects. This in-situ investigation reveals a slow wetting progression over six hours and more to obtain complete wetting, even at high fluxes of 200 LMH. However, an increased flux leads to faster wetting kinetics as the evolving wetting patterns are flux dependent. The packing density of the multibore fibers additionally impacts the wetting kinetics by shifting the prevalent pressure conditions. Although in dead-end mode, the wetting progression is non-uniform along the membrane module length. In addition to this parameter study, different pre-wetting agents' effect on the displacement behavior was investigated in depth. This study helps to understand (a) complex wetting phenomena inside multibore membranes in dead-end filtration, (b) the membranes' interaction with their surroundings due to neighboring membranes, and (c) the effect of the used fluid system for displacement on the resulting wetting patterns.
机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。