We demonstrate that polymer composites with a low loading of graphene, below 1.2 wt. %, are efficient as electromagnetic absorbers in the THz frequency range. The epoxy-based graphene composites were tested at frequencies from 0.25 THz to 4 THz, revealing total shielding effectiveness of 85 dB (1 mm thickness) with graphene loading of 1.2 wt. % at the frequency f=1.6 THz. The THz radiation is mostly blocked by absorption rather than reflection. The efficiency of the THz radiation shielding by the lightweight, electrically insulating composites, increases with increasing frequency. Our results suggest that even the thin-film or spray coatings of graphene composites with thickness in the few-hundred-micrometer range can be sufficient for blocking THz radiation in many practical applications.
The incorporation of carbon nanotubes (CNTs) within polymer hosts offers a great platform for the development of advanced thermoelectric (TE) composite materials. Over the years, several CNT/polymer composite formulations have been investigated on an effort to maximize the TE performance. Meanwhile, several studies focused on the decay dynamics of the charged excitons within CNTs itself and therefrom derived structures, aiming to investigate the lifetimes and the corresponding recombination processes of free charge carriers. The latter physical phenomena play a crucial role in the performance …
Solid-ion conductors (SICs) comprising non-ionic plastic crystals and lithium salts often require compositing with polymers to render them processable for use in solid-state lithium-metal batteries. Here, we show that polymer-doped plastic crystal SICs form a previously unrecognized plastic crystal-polymer high entropy interphase, where ions selectively partition and exhibit a higher fraction of matrix-separated ion pairs than in the bulk. Liithium ion diffusivity in this interphase is an order of magnitude higher than in other microenvironments due to an increase in the molar volume of the pl…
Carbon Nanotubes (CNTs)-polymer composites are promising candidates for a myriad of applications. Ad-hoc CNTs-polymer composite fabrication techniques inherently pose roadblock to optimized processing resulting in microstructural defects i.e., void formation, poor interfacial adhesion, wettability, and agglomeration of CNTs inside the polymer matrix. Although improvement in the microstructures can be achieved via additional processing steps such as-mechanical methods and/or chemical functionalization, the resulting composites are somewhat limited in structural and functional performances. Here…
We propose a novel approach of wet electrospinning to yield fiber-reinforced polymer ceramic composites, where a reactive ceramic precursor gel is used as a collector. We illustrate our approach by generating polyethylene oxide (PEO) fibers in a potassium silicate gel; the gel is later activated using metakaolin to yield a ceramic-0.5 wt% PEO fiber composite. An increase of 29% and 22% is recorded for the fabricated polymer ceramic composites in terms of indentation modulus and indentation hardness respectively. Our initial findings demonstrate the process viability and might lead to a potenti…
This paper addresses the numerical simulation of self-piercing rivetting processes to join fibre reinforced polymers and sheet metals. Special emphasis is placed on the modelling of the deformation and failure behaviour of the composite material. Different from the simulation of rivetting processes in metals, which requires the modelling of large plastic deformations, the mechanical response of composites is typically governed by intra- and interlaminar damage phenomena. Depending on the polymeric matrix, viscoelastic effects can interfere particularly with the long-term behaviour of the joint…
The interaction of double wall carbon nanotubes (DWCNTs) and the conducting polymer poly(3,4-ethylenedioxythiphene/polystyrenesulfonate (PEDOT/PSS) was studied by in-situ Raman spectroelectrochemistry. The mixing of DWCNTs with PEDOT/PSS caused a partial doping of the outer tube of DWCNTs, which was indicated by the relative change of the Raman intensity of the DWCNTs features. On the other hand, the bands corresponding to inner tubes of DWCNTs and to the polymer were almost untouched by assembling both species into a composite. The in situ Raman spectroelectrochemical experiments have shown t…
Correlations between electrical and thermal conduction in polymer composites are blurred due to the complex contribution of charge and heat carriers at the nanoscale junctions of filler particles. Conflicting reports on the lack or existence of thermal percolation in polymer composites have made it the subject of great controversy for decades. Here, we develop a generalized percolation framework that describes both electrical and thermal conductivity within a remarkably wide range of filler-to-matrix conductivity ratios (Y_f/Y_m), covering 20 orders of magnitude. Our unified theory provides a …
Graphene possesses unique features that make it attractive for nanotechnology. Functional devices often require combination of several materials with specific functions, and graphene-polymer composites are one of them. Herein, we report on the preparation of PEDOT:Graphene bilayers by in situ polymerization of EDOT on covalently functionalized graphene. The polymerization proceeds exclusively on the grafted graphene, and patterned structures with high spatial resolution down to 3 μm could have been prepared. The composite exhibits enhanced efficiency of electrochemical doping compared to prist…
Thermally expanded graphite (EG) polymer composite has high potential in modern thermoelectronic industry due to cost effectiveness, excellent electrical and thermal properties. In this study, we report that expanded graphite polyetherimide(EG/PEID) composite has been fabricated by simple solution mixing technique, reinforcing a low cost EG filler into host polymer matrix, polyetherimide (PEID). This technique enables the inclusion of 3D graphitic filler into polymer matrix retaining the worm structure of expanded graphite, thus developing continuous network throughout the composite. In result…
In this article we discuss in detail the effective approaches to enhance the thermal conductivity in polymer composites. It is shown from numerical simulations that maximizing interfacial area between filler and polymer enhances very significantly the effective thermal conductivity in composites. Our study outlines two main facts. (a) Although the nature of the filler's geometry plays an important role in the effective thermal conductivity, we show that among the different geometries thermal conductivity is high for those geometries for which the ratio of surface-area to volume is high. Thus n…
Memristive materials are related to neuromorphic applications as they can combine information processing with memory storage in a single computational element, just as biological neurons. Many of these bioinspired materials emulate the characteristics of memory and learning processes that happen in the brain. In this work, we report the memristive properties of a two-terminal (2-T) organic device based on ionic migration mediated by an ion-transport polymer. The material possesses unique memristive properties: it is reversibly switchable, shows tens of conductive states, presents Hebbian learn…
Due to their exceptional mechanical and chemical properties and their natural abundance, cellulose nanocrystals (CNCs) are promising building blocks of sustainable polymer composites. However, the rapid gelation of CNC dispersions has generally limited CNC-based composites to low CNC fractions, in which polymer remains the dominant phase. Here we report on the formulation and processing of crosslinked CNC-epoxy composites with a CNC fraction exceeding 50 wt.%. The microstructure comprises sub-micrometer aggregates of CNCs crosslinked to polymer, which are analogous to the lamellar structure of…
Laser-induced periodic surface structures (LIPSSs) on various materials have been extensively investigated because of their wide applications. The combination of different materials allows for greater freedom in tailoring their functions and achieving responses not possible in a homogeneous material. By utilizing a femtosecond (fs) laser to irradiate the Fe-doped Polyvinyl Pyrrolidone (PVP) composite film, highly regular ultrafine nanogratings (U-nanogratings) with a period as small as 35.0 ($\pm$ 2.0) nm can be self-organized on the surface with extremely high efficiency. The period of the U-…
