Ultra-wideband (UWB) technology is a mature technology that contested other wireless technologies in the advent of the IoT but did not achieve the same levels of widespread adoption. In recent years, however, with its potential as a wireless ranging and localization solution, it has regained momentum. Within the robotics field, UWB positioning systems are being increasingly adopted for localizing autonomous ground or aerial robots. In the Industrial IoT (IIoT) domain, its potential for ad-hoc networking and simultaneous positioning is also being explored. This survey overviews the state-of-the-art in UWB networking and localization for robotic and autonomous systems. We also cover novel techniques focusing on more scalable systems, collaborative approaches to localization, ad-hoc networking, and solutions involving machine learning to improve accuracy. This is, to the best of our knowledge, the first survey to put together the robotics and IIoT perspectives and to emphasize novel ranging and positioning modalities. We complete the survey with a discussion on current trends and open research problems.
Unmanned aerial vehicles (UAVs) are becoming largely ubiquitous with an increasing demand for aerial data. Accurate navigation and localization, required for precise data collection in many industrial applications, often relies on RTK GNSS. These systems, able of centimeter-level accuracy, require a setup and calibration process and are relatively expensive. This paper addresses the problem of accurate positioning and navigation of UAVs through cooperative localization. Inexpensive ultra-wideband (UWB) transceivers installed on both the UAV and a support ground robot enable centimeter-level re…
University of Western Brittany（西布列塔尼大学）；CNRS（法国国家科学研究中心）；Military Technical Academy（军事技术学院）
Two challenges for rescue robots are to detect human beings and to have an accurate positioning system. In indoor positioning, GPS receivers cannot be used due to the reflections or attenuation caused by obstacles. To detect human beings, sensors such as thermal camera, ultrasonic and microphone can be embedded on the rescue robot. The drawback of these sensors is the detection range. These sensors have to be in close proximity to the victim in order to detect it. UWB technology is then very helpful to ensure precise localization of the rescue robot inside the disaster site and detect human be…
University of Toronto（多伦多大学）；Vector Institute for Artificial Intelligence（向量人工智能研究所）
The combination of ultrawideband (UWB) radios and inertial measurement units (IMU) can provide accurate positioning in environments where the Global Positioning System (GPS) service is either unavailable or has unsatisfactory performance. The two sensors, IMU and UWB radio, are often not co-located on a moving system. The UWB radio is typically located at the extremities of the system to ensure reliable communication, whereas the IMUs are located closer to its center of gravity. Furthermore, without hardware or software synchronization, data from heterogeneous sensors can arrive at different t…
Determining assets position with high accuracy and scalability is one of the most investigated technology on the market. The accuracy provided by satellites-based positioning systems (i.e., GLONASS or Galileo) is not always sufficient when a decimeter-level accuracy is required or when there is the need of localising entities that operate inside indoor environments. Scalability is also a recurrent problem when dealing with indoor positioning systems. This paper presents an innovative UWB Indoor GPS-Like local positioning system able to tracks any number of assets without decreasing measurement…
Ultra-wideband (UWB) ranging has emerged as a key radio technology for robot positioning and relative localization in multi-robot systems. Multiple works are now advancing towards more scalable systems, but challenges still remain. This paper proposes a novel approach to relative localization in multi-robot systems where the roles of the UWB nodes are dynamically allocated between active nodes (using time-of-flight for ranging estimation to other active nodes) and passive nodes (using time-difference-of-arrival for estimating range differences with respect to pairs of active nodes). We adaptiv…
The automatic road roller, as a popular type of construction robot, has attracted much interest from both the industry and the research community in recent years. However, when it comes to tunnels where the degeneration issues are prone to happen, it is still a challenging problem to provide an accurate positioning result for the robot. In this paper, we aim to deal with this problem by fusing LiDAR and UWB measurements based on optimization. In the proposed localization method, the directions of non-degeneration will be constrained and the covariance of UWB reconstruction will be introduced t…
Driven by applications like Micro Aerial Vehicles (MAVs), driver-less cars, etc, localization solution has become an active research topic in the past decade. In recent years, Ultra Wideband (UWB) emerged as a promising technology because of its impressive performance in both indoor and outdoor positioning. But algorithms relying only on UWB sensor usually result in high latency and low bandwidth, which is undesirable in some situations such as controlling a MAV. To alleviate this problem, an Extended Kalman Filter (EKF) based algorithm is proposed to fuse the Inertial Measurement Unit (IMU) a…
University of Toronto（多伦多大学）；Vector Institute for Artificial Intelligence（向量人工智能研究所）
Ultra-wideband (UWB) time difference of arrival (TDOA)-based localization has recently emerged as a promising indoor positioning solution. However, in cluttered environments, both the UWB radio positions and the obstacle-induced non-line-of-sight (NLOS) measurement biases significantly impact the quality of the position estimate. Consequently, the placement of the UWB radios must be carefully designed to provide satisfactory localization accuracy for a region of interest. In this work, we propose a novel algorithm that optimizes the UWB radio positions for a pre-defined region of interest in t…
Navigation in an unknown environment without any preexisting positioning infrastructure has always been hard for mobile robots. This paper presents a self-deployable ultra wideband UWB infrastructure by mobile agents, that permits a dynamic placement and runtime extension of UWB anchors infrastructure while the robot explores the new environment. We provide a detailed analysis of the uncertainty of the positioning system while the UWB infrastructure grows. Moreover, we developed a genetic algorithm that minimizes the deployment of new anchors, saving energy and resources on the mobile robot an…
Uncertainty-aware Gaussian Mixture Model for UWB Time Difference of Arrival Localization in Cluttered Environments
University of Toronto（多伦多大学）；University of Toronto Robotics Institute（多伦多大学机器人研究所）；Vector Institute for Artificial Intelligence（矢量人工智能研究所）；Technical University of Munich（慕尼黑工业大学）；Munich Institute for Robotics and Machine Intelligence（慕尼黑机器人与机器智能研究所）
For a team of robots to work collaboratively, it is crucial that each robot have the ability to determine the position of their neighbors, relative to themselves, in order to execute tasks autonomously. This letter presents an algorithm for determining the three-dimensional relative position between two mobile robots, each using nothing more than a single ultra-wideband transceiver, an accelerometer, a rate gyro, and a magnetometer. A sliding window filter estimates the relative position at selected keypoints by combining the distance measurements with acceleration estimates, which each agent …
UTIL: An Ultra-wideband Time-difference-of-arrival Indoor Localization Dataset
University of Toronto Institute for Aerospace Studies (UTIAS)（多伦多大学航空航天研究所）；University of Toronto Robotics Institute（多伦多大学机器人研究所）；Vector Institute for Artificial Intelligence（向量人工智能研究所）；Technical University of Munich（慕尼黑工业大学）；Munich Institute for Robotics and Machine Intelligence (MIRMI)（慕尼黑机器人与机器智能研究所）
Institute for Aerospace Studies（航空航天研究所）；University of Toronto（多伦多大学）
The combination of ultrawideband (UWB) radios and inertial measurement units (IMU) can provide accurate positioning. To ensure reliable communication, the radios are generally mounted at the extremities of a mobile system whereas the IMUs are located closer to the center of gravity for use in control, resulting in a spatial offset between the IMU and the UWB radio. Additionally, data from heterogeneous sensors can arrive at different time instants. The systematic fusion of data from multiple sources requires the temporal offset and spatial offset between the sensors to be known. An important a…
Range-SLAM: Ultra-Wideband-Based Smoke-Resistant Real-Time Localization and Mapping
Shenzhen International Graduate School, Tsinghua University（清华大学深圳国际研究生院）；Pengcheng Lab（鹏城实验室）；RISC-V International Open Source Laboratory（RISC-V国际开源实验室）
Singapore University of Technology and Design（新加坡科技设计大学）；Southwest University of Science and Technology（西南科技大学）；University of Turbat（图尔巴特大学）
Environment mapping is an essential prerequisite for mobile robots to perform different tasks such as navigation and mission planning. With the availability of low-cost 2D LiDARs, there are increasing applications of such 2D LiDARs in industrial environments. However, environment mapping in an unknown and feature-less environment with such low-cost 2D LiDARs remains a challenge. The challenge mainly originates from the short-range of LiDARs and complexities in performing scan matching in these environments. In order to resolve these shortcomings, we propose to fuse the ultra-wideband (UWB) wit…
Robust Online Calibration for UWB-Aided Visual-Inertial Navigation with Bias Correction
Department of Electrical and Computer Engineering, George Mason University（乔治·马歇尔大学电气与计算机工程系）；Department of Electrical and Computer Engineering, University of California, Riverside（加州大学河滨分校电气与计算机工程系）；Department of Electrical Engineering and Computer Science, University of Tennessee, Knoxville（田纳西大学克林顿分校电气工程与计算机科学系）
CT-UIO: Continuous-Time UWB-Inertial-Odometer Localization Using Non-Uniform B-spline with Fewer Anchors
National Engineering Research Center of Robot Visual Perception and Control Technology, Hunan University（湖南大学机器人视觉感知与控制技术国家工程研究中心）；School of Artificial Intelligence, Changsha University of Science and Technology（长沙理工大学人工智能学院）；School of Artificial Intelligence and Robotics, Hunan University（湖南大学人工智能与机器人学院）；State Key Laboratory of Chemistry for NBC Hazards Protection, Beijing（核生化防护化学重点实验室，北京）
In order to decrease the measuring cycle time on the coordinate measuring machine (CMM) a robot workstation for the positioning of measuring objects was created. The application of a simple 5-axis industrial robot enables the positioning of the objects within the working space of CMM and measuring of different surfaces on the same object without human intervention. In this article an upgrade of an existing robot workstation through different design measures is shown. The main goal of this upgrade is to improve the measuring accuracy of the complex robot-CMM system.
Chongqing University of Posts and Telecommunications（重庆邮电大学）；Swansea University（斯旺西大学）
Industrial robot arms are extensively important for intelligent manufacturing. An industrial robot arm commonly enjoys its high repetitive positioning accuracy while suffering from its low absolute positioning accuracy, which greatly restricts its application in high-precision manufacture, like automobile manufacture. Aiming at addressing this hot issue, this work proposes a novel robot arm calibration method based on cubic interpolated beetle antennae search (CIBAS). This study has three ideas: a) developing a novel CIBAS algorithm, which can effectively addresses the issue of local optimum i…
University of Southern California（南加州大学）；NASA Goddard Space Flight Center（美国国家航空航天局戈达德太空飞行中心）
Motivated by lunar exploration, we consider deploying a network of mobile robots to explore an unknown environment while acting as a cooperative positioning system. Robots measure and communicate position-related data in order to perform localization in the absence of infrastructure-based solutions (e.g. stationary beacons or GPS). We present Trilateration for Exploration and Mapping (TEAM), a novel algorithm for low-complexity localization and mapping with robotic networks. TEAM is designed to leverage the capability of commercially-available ultra-wideband (UWB) radios on board the robots to…
UAV Object Detection and Positioning in a Mining Industrial Metaverse with Custom Geo-Referenced Data
Department of Production and Management Engineering, Democritus University of Thrace（生产与管理工程系，德米特里乌斯·特拉基斯大学）；Department of Electrical and Computer Engineering, Democritus University of Thrace（电气与计算机工程系，德米特里乌斯·特拉基斯大学）
Indoor autonomous navigation requires a precise and accurate localization system able to guide robots through cluttered, unstructured and dynamic environments. Ultra-wideband (UWB) technology, as an indoor positioning system, offers precise localization and tracking, but moving obstacles and non-line-of-sight occurrences can generate noisy and unreliable signals. That, combined with sensors noise, unmodeled dynamics and environment changes can result in a failure of the guidance algorithm of the robot. We demonstrate how a power-efficient and low computational cost point-to-point local planner…
This work develops a tracking system based on an event-based camera. A bioinspired filtering algorithm to reduce noise and transmitted data while keeping the main features at the scene is implemented in FPGA which also serves as a network node. POWERLINK IEEE 61158 industrial network is used to communicate the FPGA with a controller connected to a self-developed two axis servo-controlled robot. The FPGA includes the network protocol to integrate the event-based camera as any other existing network node. The inverse kinematics for the robot is included in the controller. In addition, another ne…
Chongqing University of Posts and Telecommunications（重庆邮电大学）；Swansea University（斯旺西大学）；Southwest University（西南大学）
Industrial robots play a vital role in automatic production, which have been widely utilized in industrial production activities, like handling and welding. However, due to an uncalibrated robot with machining tolerance and assembly tolerance, it suffers from low absolute positioning accuracy, which cannot satisfy the requirements of high-precision manufacture. To address this hot issue, we propose a novel calibration method based on an unscented Kalman filter and variable step-size Levenberg-Marquardt algorithm. This work has three ideas: a) proposing a novel variable step-size Levenberg-Marq…
Design And Control of A Robotic Arm For Industrial Applications
CMR Technical Campus（CMR技术学院）；JNTUH University College of Engineering, Science & Technology Hyderabad（贾瓦哈拉尔·尼赫鲁科技大学海得拉巴工程科学与技术学院）；Holy Mary Institute of Technology（圣玛丽技术学院）
Relative localization is an important ability for multiple robots to perform cooperative tasks in GPS-denied environment. This paper presents a novel autonomous positioning framework for monocular relative localization of multiple tiny flying robots. This approach does not require any groundtruth data from external systems or manual labelling. Instead, the proposed framework is able to label real-world images with 3D relative positions between robots based on another onboard relative estimation technology, using ultra-wide band (UWB). After training in this self-supervised manner, the proposed…
In recent years, multi-robot systems have received increasing attention from both industry and academia. Besides the need of accurate and robust estimation of relative localization, security and trust in the system are essential to enable wider adoption. In this paper, we propose a framework using Hyperledger Fabric for multi-robot collaboration in industrial applications. We rely on blockchain identities for the interaction of ground and aerial robots, and use smart contracts for collaborative decision making. The use of ultra-wideband (UWB) localization for both autonomous navigation and rob…
University Politehnica of Bucharest（布加勒斯特理工大学）；University Bordeaux 1（波尔多第一大学）
The six axis robots are widely used in automotive industry for their good repeatability (as defined in the ISO92983) (painting, welding, mastic deposition, handling etc.). In the aerospace industry, robot starts to be used for complex applications such as drilling, riveting, fiber placement, NDT, etc. Given the positioning performance of serial robots, precision applications require usually external measurement device with complexes calibration procedure in order to reach the precision needed. New applications in the machining field of composite material (aerospace, naval, or wind turbine for …
Chongqing University of Posts and Telecommunications（重庆邮电大学）；Swansea University（斯旺西大学）
Recently, industrial robots plays a significant role in intelligent manufacturing. Hence, it is an urgent issue to ensure the robot with the high positioning precision. To address this hot issue, a novel calibration method based on an powerful ensemble with various algorithms is proposed. This paper has two ideas: a) developing eight calibration methods to identify the kinematic parameter errors; 2) establishing an effective ensemble to search calibrated kinematic parameters. Enough experimental results show that this ensemble can achieve: 1) higher calibration accuracy for the robot; 2) model…
SPI-BoTER: Error Compensation for Industrial Robots via Sparse Attention Masking and Hybrid Loss with Spatial-Physical Information
School of Software（软件学院）；Northwestern Polytechnical University（西北工业大学）；School of Computer Science and Technology（计算机科学与技术学院）；University of Science and Technology of China（中国科学技术大学）；Suzhou Key Lab of Aerospace Industry Software and Data Science（苏州航空航天软件与数据科学重点实验室）；Yangtze River Delta Research Institute of NPU（南京航空航天大学长江三角洲研究院）
Robert Bosch Center for Cyberphysical Systems, Indian Institute of Science（印度科学理工学院罗伯特·博世网络物理系统中心）；Indian Institute of Technology Bombay（印度理工学院孟买分校）；Indian Institute of Technology Madras（印度理工学院马德拉斯分校）
Current trends in autonomous vehicles and their applications indicates an increasing need in positioning at low battery and compute cost. Lidars provide accurate localization at the cost of high compute and power consumption which could be detrimental for drones. Modern requirements for autonomous drones such as No-Permit-No-Takeoff (NPNT) and applications restricting drones to a corridor require the infrastructure to constantly determine the location of the drone. Ultra Wide Band Radios (UWB) fulfill such requirements and offer high precision localization and fast position update rates at a f…
Khalifa University of Science and Technology（哈利法科技大学）；Strata Manufacturing PJSC（斯特拉塔制造公司）
The manufacturing industry is currently witnessing a paradigm shift with the unprecedented adoption of industrial robots, and machine vision is a key perception technology that enables these robots to perform precise operations in unstructured environments. However, the sensitivity of conventional vision sensors to lighting conditions and high-speed motion sets a limitation on the reliability and work-rate of production lines. Neuromorphic vision is a recent technology with the potential to address the challenges of conventional vision with its high temporal resolution, low latency, and wide d…
