In this work, we introduce the platform of plasmonic Doppler grating (PDG) to experimentally investigate the enhancement effect of plasmonic gratings in the input and output beams of nonlinear surface-enhanced coherent anti-Stokes Raman scattering (SECARS). PDGs are designable azimuthally chirped gratings that provide broadband and spatially dispersed plasmonic enhancement. Therefore, they offer the opportunity to observe and compare the overall enhancement from different combinations of enhancement in individual input and output beams. We first confirm PDG's capability of spatially separating the input and output enhancement in linear surface-enhanced fluorescence and Raman scattering. We then investigate spatially resolved enhancement in nonlinear SECARS, where coherent interaction of the pump, Stokes, and anti-Stokes beams is enhanced by the plasmonic gratings. By mapping the SECARS signal and analyzing the azimuthal angle-dependent intensity, we characterize the enhancement at individual frequencies. Together with theoretical analysis, we show that while simultaneous enhancement in the input and output beams is important for SECARS, the enhancement in the pump and anti-Stokes beams plays a more critical role in the overall enhancement than that in the Stokes beam. This work provides an insight into the enhancement mechanism of plasmon-enhanced spectroscopy, which is important for the design and optimization of plasmonic gratings. The PDG platform may also be applied to study enhancement mechanisms in other nonlinear light-matter interactions or the impact of plasmonic gratings on the fluorescence lifetime.
The deployment of plasmonic nanostructures to enhance nonlinear signal generation requires effective far-to-near field coupling and phase matching for frequency conversion. While the latter can be easily achieved at plasmonic hotspots, the former is an antenna problem that requires dedicated structural design and optimization. Plasmonic gratings are a simple but effective platform for nonlinear signal generation since they provide a well-defined momentum for photon-plasmon coupling and local hotspots for frequency conversion. In this work, a plasmonic azimuthally chirped grating (ACG), which p…
Plasmonic gratings constitute a paradigmatic instance of the wide range of applications enabled by plasmonics. While subwavelength metal gratings find applications in optical biosensing and photovoltaics, atomically thin gratings achieved by periodically doping a graphene monolayer perform as metasurfaces for the control of terahertz radiation. In this paper we show how these two instances of plasmonic gratings inherit their spectral properties from an underlying slab with translational symmetry.We develop an analytical formalism to accurately derive the mode spectrum of the gratings that prov…
We propose a compound system consisting of a dielectric grating and a plasmonic resonance cavity embedded in the grating. Based on the interference effect between the surface mode supported by the dielectric grating and the plasmonic-induced cavity mode, this system could achieve slow light with group index more than 200 and transmission more than 75%. Meanwhile, we examine the effects of the period numbers of the compound system and photonic crystal superlattice made up of alternate layers of the grating and air on the properties of slow light.
The modified rigorous coupled-wave analysis technique is developed to describe the optical characteristics of the plasmonic structures with the grating-gated delta-thin conductive channel in the far- and near-field zones of electromagnetic waves. The technique was applied for analysis of the resonant properties of AlGaN/GaN heterostructures combined with deeply-subwavelength metallic grating which facilitates the excitation of the two-dimensional plasmons in the THz frequency range. The convergence of the calculations at the frequencies near the plasmon resonances is discussed. The impact of t…
A composite plasmonic slab based on double-layer metallic gratings and a dielectric film is experimentally and numerically demonstrated in terahertz (THz) regions, which can support two resonance modes and then form a broad bandgap (40%). As compared to the double-layer metal grating, the dielectric film in composite THz slabs significantly enhances the transmission of the transverse magnetic (TM) mode. Electric field vector proved that the low-frequency resonance mode originates from the symmetric plasmonic mode and the high-frequency resonance mode is induced by the hybrid mode of plasmonic …
We report the first experimental observation of trapped rainbow1 in graded metallic gratings2-4, designed to validate theoretical predictions for this new class of plasmonic structures. One-dimensional tapered gratings were fabricated and their surface dispersion properties tailored by varying the grating period and depth, whose dimensions were confirmed by atomic force microscopy. Reduced group velocities and the plasmonic bandgap were observed. Direct measurements on graded grating structures show that light of different wavelengths in the 500-700nm region is "trapped" at different positions…
The general features of the light scattering resulting in the so-called resonant Wood's anomalies in the reflection and transmission spectra are described using the effective parameters of a quasi-guided mode. The expression determining the spectral angular dependence of Wood's anomaly in the case of plasmonic grating structures is given and compared to the analogous expression for dielectric grating structures. Comparison of the resonant Wood's anomalies (RWA) with the surface plasmon-polariton resonances (SPPRs) is discussed as well.
We demonstrate an approach, based on plasmonic apertures and gratings, to enhance the radiative decay rate of single NV centers in diamond, while simultaneously improving their collection efficiency. Our structures are based on metallic resonators formed by surrounding sub-wavelength diamond nanoposts with a silver film, which can enhance the spontaneous emission rate of an embedded NV center. However, the collection efficiency of emitted photons remains low due to losses to surface plasmons and reflections at the diamond-air interface. In this work, we mitigate photon losses into these channe…
We present two-dimensional plasmonic Doppler grating (PDG) for broadband azimuthal angle-resolved nanophotonic applications. The PDG consists of a set of non-concentric circular rings mimicking the wavefronts of a moving point source that exhibits Doppler Effect and thereby offers continuous azimuthal angle-dependent lattice momentum for photon-plasmon coupling. The center and span of the working frequency window are fully designable for optimal performance in specific applications. We detail the design, fabrication and optical characterization of the PDG. The design of Doppler grating provide…
The propagation of solitary waves in a Bragg grating formed by an array of thin nanostructured dielectric films is considered. A system of equations of Maxwell-Duffing type and describing forward- and backward-propagating waves in such a grating, is derived. Exact solitary wave solutions are found, analyzed, and compared with the results of direct numerical simulations.
Plasmonic enhancement of nonlinear light-matter interaction can be achieved via dedicated optimization of resonant plasmonic modes that are spectrally matched to the different wavelengths involved in the particular nonlinear optical process. In this work, we investigate the generation and enhancement of broadband four-wave mixing (FWM) in a plasmonic azimuthally chirped grating (ACG). The azimuthally varying grating periodicity in an ACG offers a well-defined channel to mediate the near field and the far field over a broad range of wavelengths. However, the particular mechanism responsible for…
We report the possibility to generate tremendous light-field enhancements within shallow nano-trenches made in a high index dielectric material, because of resonant behaviours reminiscent of what we get with sub-wavelength plasmonic cavities. The high quality factors are explained through a modal analysis and can be tuned with appropriate design rules. The thin dielectric void gratings here simulated could be a relevant alternative to plasmon-based devices for chemical sensing, or could be used as efficient wavelength-selective photo-absorbers by taking weakly absorbing materials.
Optical nanosensors are promising for hydrogen sensing because they are small, free from spark generation, and feasible for remote optical readout. Conventional optical nanosensors require broadband excitation and spectrometers, rendering the devices bulky and complex. An alternative is spatial intensity-based optical sensing, which only requires an imaging system and a smartly designed platform to report the spatial distribution of analytical optical signals. Here, we present a spatial intensity-based hydrogen sensing platform based on Fano-like spatial distribution of the transmission in a P…
Light propagation in a Bragg periodic structure containing thin films with metallic nanoparticles is studied. Plasmonic resonance frequency, Bragg frequency, and light carrier frequency are assumed to be close. Exact solutions describing solitary gap-waves are found, and a light arrest phenomenon due to nonlinearity of plasmonic oscillations is studied.
The ability of curved gratings as sectors of concentric circular gratings to couple linearly polarized light into focused surface plasmons is investigated by theory, simulation and experiment. Curved gratings, as sectors of concentric circular gratings with four different sector angles, are etched into a 30-nm thick gold layer on a glass coverslip and used to couple linearly-polarised free space light at nm into surface plasmons. The experimental and simulation results show that increasing the sector angle of the curved gratings decreases the lateral spotsize of the excited surface plasmons, r…
We present a computational study of terahertz optical properties of a grating-coupled plasmonic structure based on micrometer-thin InSb layers. We find two strong absorption resonances that we interpret as standing surface plasmon modes and investigate their dispersion relations, dependence on InSb thickness, and the spatial distribution of the electric field. The observed surface plasmon modes are well described by a simple theory of the air/InSb/air trilayer. The plasmonic response of the grating/InSb structure is highly sensitive to the dielectric environment and the presence of an analyte …
We report a novel design of a compact wavelength add-drop multiplexer utilizing dielectric-loaded surface plasmon-polariton waveguides (DLSPPWs). The DLSPPW-based configuration exploits routing properties of directional couplers and filtering abilities of Bragg gratings. We present practical realization of a 20-$μ$m-long device operating at telecom wavelengths that can reroute optical signals separated by approximately 70 nm in the wavelength band. We characterize the performance of the fabricated structures using scanning near-field optical microscopy as well as leakage-radiation microscopy a…
We demonstrate that plasmonic helical gratings consisting of metallic nanowires imprinted with helical grooves or ridges can be used efficiently to generate plasmonic vortices with radius much smaller than the operating wavelength. In our proposed approach, these helical surface gratings are designed so that plasmon modes with different azimuthal quantum numbers (topological charge) are phase-matched, thus allowing one to generate optical plasmonic vortices with arbitrary topological charge. The general principles for designing plasmonic helical gratings that facilitate efficient generation of…
In this work, we proposed a high resolution D-shaped photonic crystal fiber (PCF) surface plasmon resonance (SPR) sensor based on gold grating. Gold grating is introduced to modulate the resonance wavelength and enhance the refractive index (RI) sensitivity. Structure parameters of PCF and gold grating are analyzed by finite element method (FEM) for optimizing the SPR sensor. The simulation results indicate that air hole pitch, air hole diameter and gold thickness and grating constant have little influence on the sensitivity of refractive index, which reduces the requirement of precise process…
We configure and analyze a nanostructured device that hybridizes grating modes and surface plasmon resonances. The model uses an effective index of refraction that considers the volume fraction of the involved materials, and the propagation depth of the plasmon through the structure. Our geometry is an extruded low-order diffraction grating made of dielectric nano-triangles. Surface plasmon resonances are excited at a metal/dielectric interface, which is separated from the analyte by a high-index dielectric layer. The optical performance of the refractometric sensor is highly competitive in se…
We provide rigorous numerical calculations (using the rigorous coupled-wave analysis) of transmission spectra of various metallic and metamaterial one-dimensional gratings and identify plasmonic resonances responsible for enhanced transmission. We argue that the most important mechanism which influences the resonant transmission is the coupling of incident electromagnetic wave with two plasmonic waves: lengthwise plasmons, which propagates along the grating, and crosswise plasmons excited in air gaps.
We experimentally measure and analytically describe the fluorescence enhancement obtained by depositing CdSe/CdS nanocrystals onto a gold plasmonic crystal, a two-dimensional grating of macroscopic size obtained by gold deposition on a self-assembled opal. We show evidences of nanocrystals near-field coupling to the gold Surface Plasmons Polaritons (SPP) followed by grating-induced SPP re-emission to far-field. We develop a theoretical framework and an original method in order to evaluate, from photoluminescence experiments, the SPP extraction efficiency of a grating.
Plasmonic gratings of different periodicities are fabricated on top of Silicon nanocrystals embedded in Silicon Dioxide. Purcell enhancements of up to 2 were observed, which matches the value from simulations. Plasmonic enhancements are observed for the first three orders of the plasmonic modes, with the peak enhancement wavelength varying with the periodicity. Biharmonic gratings are also fabricated to extract the enhanced emission from the first order plasmonic mode, resulting in enhancements with quality factors of up to 16.
Typical nanoparticle-based plasmonic index sensors detect the spectral shift of localized surface plasmon resonance (LSPR) upon the change of environmental index. Therefore, they require broadband illumination and spectrometers. The sensitivity and flexibility of nanoparticle-based index sensors are usually limited because LSPR peaks are usually broad and the spectral position cannot be freely designed. Here, we present a fully designable index sensing platform using a plasmonic Doppler grating (PDG), which provides broadband and azimuthal angle-dependent grating periodicities. Different from …
The thermal emission of refractory plasmonic metamaterial - a titanium nitride 1D grating - is studied at high operating temperature (540 °C). By choosing a refractory material, we fabricate thermal gratings with high brightness that are emitting mid-infrared radiation centered around 3 $μ$m. We demonstrate experimentally that the thermal excitation of plasmon-polariton on the surface of the grating produces a well-collimated beam with a spatial coherence length of 32λ (angular divergence of 1.8°) which is quasi-monochromatic with a full width at half maximum of 70 nm. These experimental resul…
2D and 3D micro/nano fabrication based on two-photon polymerization (TPP) has emerged as a strong contender for additive manufacturing for wide variety of applications. In this manuscript we report one step patterning of structurally stable, subwavelength 2D and 3D gold nanostructures using femto-second laser by incorporating single photon photoinitiator only in pure and metal precursor doped polymers. The metal polymer composite nanostructures are written directly by in-situ reduction of gold precursor within the photoresist using femto-second laser irradiation. The photo-initiator triggers t…
Using the Fourier modal method (FMM) we report our analysis of the transmission resonances of a plasmonic grating with sub-wavelength period and extremely narrow slits for wavelengths of the incoming, transverse magnetic (TM)-polarized, radiation ranging from 240nm to 1500nm and incident angles from 0 degree to 90 degree. In particular, we study the case of a silver grating placed in vacuo. Consistent with previous studies on the topic, we highlight that the main mechanism for extraordinary transmission is a TM-Fabry-Perot (FP) branch supported by waveguide modes inside each slit. The TM-FP br…
We present a concept for an ultra-thin solar fuel device with a nanostructured back contact. Using rigorous simulations we show that the nanostructuring significantly increases the absorption in the semiconductor, CuBi$_2$O$_4$ in this case, by 47\% (5.2~mAcm$^{-2}$) through the excitation of plasmonic modes. We are able to attribute the resonances in the device to metal-insulator-metal plasmons coupled to either localised surface plasmon resonances or surface plasmon polaritons. Rounding applied to the metallic corners leads to a blueshift in the resonance wavelength while maintaining absorpt…
Diffraction gratings are famous for their ability to exhibit, near a Wood anomaly, an arbitrarily large angular dispersion, e.g., with respect to the incidence angle or wavelength. For a diffraction grating under incidence by a plane wave at a fixed frequency, by rotating the incidence angle at a given angular velocity, the field propagated by a nonzero diffraction order will rotate at increasingly fast angular velocity as the incidence angle approaches the angle where Wood anomaly occurs. Such a fast rotating diffracted field has the potential to generate a substantial Doppler shift. Indeed, …
We consider the spectral response of moving diffraction gratings, in which the incident light extends over a broad angular range and where the diffracted light is observed from a specific angle. We show that the dispersion relation between the frequency perceived by an observer who is looking at a moving grating and the incident frequency can exhibit some unique features, such as a flat band (i.e., a local minimum). An observer can see the light diffracted into a non-specular diffraction order from a multitude of incident light rays and the angle of incidence of each ray is frequency-dependent…
High input intensities are usually required to efficiently excite optical nonlinear effects in ultrathin structures. This problem is particularly critical at terahertz (THz) frequencies because high input power THz sources are not available. The demonstration of enhanced nonlinear effects at THz frequencies is particularly important since these nonlinear mechanisms promise to play a significant role in the development and design of new reconfigurable planar THz nonlinear devices. In this work, we present a novel class of ultrathin nonlinear hybrid planar THz devices based on graphene-covered p…
We propose a novel technique for the magnetoplasmonic nanostructures fabrication based on the pulse force nanolithography method. It allows one to create the high-quality magnetoplasmonic nanostructures that have lower total losses than the gratings made by the electron beam lithography. The method provides control of the SPP excitation efficiency by varying the grating parameters such as the scratching depth or the number of the scratches in a single period. The quality of the plasmonic gratings was estimated by means of the transverse magneto-optical Kerr effect that is extremely sensitive t…
Plasmonic gratings and nano-particle arrays in a metal-insulator-metal structures are fabricated on an erbium doped silicon nitride layer. This material system enables simple fabrication of the structure, since the active nitride layer can be directly grown on metal. Enhancement of collected emission of up to 12 is observed on resonance, while broad off-resonant enhancement is also present. The output polarization behavior of the gratings and nano-particle arrays is investigated and matched to plasmonic resonances, and the behavior of coupled modes as a function of inter-particle distance is a…
In this paper, we design and simulate a terahertz (THz) controllable active plasmonic waveguide structure based on a single graphene layer that is placed on a random silicon grating substrate. Optical gain in the proposed THz active plasmonic waveguide structure is provided by the stimulated emission process in the photoexcited graphene monolayer that leads to the amplification of surface plasmon polariton (SPP) waves. We use a random grating substrate to introduce Anderson localization of the SPP waves propagating through the graphene monolayer to enhance their optical amplification at resona…
Recent experiments have shown that spatial dispersion may have a conspicuous impact on the response of plasmonic structures. This suggests that in some cases the Drude model should be replaced by more advanced descriptions that take spatial dispersion into account, like the hydrodynamic model. Here we show that nonlocality in the metallic response affects surface plasmons propagating at the interface between a metal and a dielectric with high permittivity. As a direct consequence, any nanoparticle with a radius larger than 20 nm can be expected to be sensitive to spatial dispersion whatever it…
We theoretically study the interactions between plasmonic and photonic modes within a structure that is composed of two thin corrugated metallic plates, embedded in air. We show that the interactions depend upon the symmetry of the interacting modes. This observation is explained by the phase difference between the Fourier components of the two gratings. The phase can be controlled by laterally shifting one grating with respect to the other. Therefore, this relative shift provides an efficient "knob" that allows to control the interaction between the various modes, resulting in an efficient mo…
In this paper, we propose a one-dimensional disordered plasmonic structure composed of a graphene single layer placed on a random grating composed of InAs. The propagation of a plasmonic wave through this structure is investigated numerically. By calculation of normalized localization length for systems with different disorder strengths, it is determined whether or not the system is in the localized regime. For some frequencies, depending on the disorder level, Anderson localization occurs for plasmonic waves propagating through the graphene layer. Furthermore, the effect of optical loss on th…
Oblique Bragg-Doppler scattering at relativistic grating created by backward Raman amplification in hydrogen
Russell Centre for Advanced Lightwave Science, Shanghai Institute of Optics and Fine Mechanics and Hangzhou Institute of Optics and Fine Mechanics, Chinese Academy of Sciences (CAS)（中国科学院上海光学精密机械研究所杭州分院）；University of Chinese Academy of Sciences（中国科学院大学）；Zhejiang Key Laboratory of Microstructured Specialty Optical Fiber, Hangzhou Institute of Optics and Fine Mechanics（浙江省微结构特种光纤重点实验室，中国科学院上海光学精密机械研究所杭州分院）
Simulation results, fabrication details and measurements are presented for a one dimensional aperture and grating array for the purpose of plasmonic beam shaping of the λ=3.99μm output of an optically pumped semiconductor laser.
On-chip nanophotonics serves as the foundation for the new generation of information technology, but it is challenged by the diffraction limit of light. With the capabilities of confining light into (deep) subwavelength volumes, plasmonics makes it possible to dramatically miniaturize optical devices so as to integrate them into silicon chips. Here we demonstrate that by cascading nano-corrugation gratings with different periodicities on silver nanowires atop silicon, different colors can be spatially separated and chronologically released at different grating junctions. The released light fre…
In this paper, we present a plasmonic refractometric sensor that works under normal incidence; allowing its integration on a fiber tip. The sensor's material and geometry exploit the large scattering cross-section given by high-contrast of the index of refraction subwavelength dielectric gratings. Our design generates a hybrid plasmonic-Fano resonance due to the interference between the surface plasmon resonance and the grating response. We optimize the sensor with a merit function that combines the quality parameter of the resonance and the field enhancement at the interaction volume where th…
Excitation of coherent optical phonons in solids provides a pathway for ultrafast modulation of light on a sub-ps timescale. Here, we report on efficient 3.6 THz modulation of light reflected from hybrid metal/semiconductor plasmonic crystals caused by lattice vibrations in a few nm thick layer of elemental tellurium. We observe that surface plasmon polaritons contribute significantly to photoinduced formation of this thin layer at the interface between a telluride-based II-VI semiconductor, such as (Cd,Mg)Te or (Cd,Mn)Te, and a one-dimensional gold grating. The change in interface composition…
Linear birefringence, as implemented in wave plates, is a natural way to control the state of polarization of light. We report on a general method for designing miniature planar wave plates using surface plasmons. The resonant optical device considered here is a single circular aperture surrounded by an elliptical antenna grating. The difference in short and long axis of each ellipses introduces a phase shift on the surface plasmons which enables the realization of a quarter wave plate. Furthermore, the experimental results and the theoretical analysis show that the general procedure used does…
Fano resonance exhibiting an asymmetric spectral line shape is a universal phenomenon observed in diverse physical systems. Here we experimentally establish a direct link between the spectral asymmetry parameter and a physically realizable phase factor of interference between a continuum and a discrete mode that leads to Fano resonance. Using a specially designed metamaterial, namely waveguided plasmonic crystal with a spatially varying orientation axis of plasmonic grating, we demonstrate control on the spectral asymmetry of the Fano resonance through changes in the geometric phase of polariz…
Experiments on the excitation of propagating surface plasmons (SPs) by ultrashort, high intensity laser interaction with "grating" targets are reviewed. At intensities exceeding $10^{19}~\mbox{W cm}^{-2}$ on target, i.e. in the strongly relativistic regime of electron dynamics, multi-MeV electrons are accelerated by the SP field as dense bunches collimated in a near-tangent direction. By the use of a suitable blazed grating, the bunch charge can be increased up to $\simeq $660 picoCoulomb. Intense XUV high harmonics (HH) diffracted by the grating are observed when a plasma with sub-micrometer …
A periodic arrangement of chains of gold discs shows pronounced plasmonic grating resonances. These have a clear impact on the Surface Enhanced Raman Scattering (SERS)-signal from 4-methylbenzenethiol molecules which form self-assembled monolayers on the gold surface: Besides a clear polarisation dependence the SERS-spectra also exhibit a maximum when the excitation laser wavelength matches the plamonic grating resonance. These features are explained by a combined near and far field coupling of the individual plasmonic dipoles allowing the design of optimized nanostructures for effective SERS-…
In this work, a 2D magneto-plasmonic grating structure combining materials with ferromagnetic and plasmonic properties is demonstrated. NiFe composite ferromagnetic material, as an active medium with tunable physical properties, and Au metal, as a plasmonic excitation layer, were the materials of choice. Here, we have experimentally investigated the active control of the plasmonic characteristics in Au/NiFe bilayer by the action of an external magnetic field, as well as the switching effect of the system. The active plasmonic control, can be achieved by the magnetization switching of the ferro…
We study how the collective effects of nanoparticles arranged in rectangular arrays influence their temporal plasmon response and field enhancement property. By systematically changing the lattice constant for arrays containing identical metal nanorods, we experimentally demonstrate how grating induced effects affect the position and, more importantly, the broadening of extinction spectra. We correlate these effects with the achievable field enhancement and the temporal duration of plasmon transients and formulate criteria for the generation of enhanced few-cycle localized plasmon oscillations…
Linear Arrays of Metal-Coated Microspheres: a Polarization-Sensitive Hybrid Colloidal Plasmonic-Photonic Crystal
National Institute for Research and Development of Isotopic and Molecular Technologies INCDTIM（同位素和分子技术研究与发展国家研究所）；Institute for Interdisciplinary Research in Bio-Nano-Sciences, Babes-Bolyai University（巴比什-博尧伊大学生物纳米科学跨学科研究所）
