We study the problem of downlink channel estimation in multi-user massive multiple input multiple output (MIMO) systems. To this end, we consider a Bayesian compressive sensing approach in which the clustered sparse structure of the channel in the angular domain is employed to reduce the pilot overhead. To capture the clustered structure, we employ a conditionally independent identically distributed Bernoulli-Gaussian prior on the sparse vector representing the channel, and a Markov prior on its support vector. An expectation propagation (EP) algorithm is developed to approximate the intractable joint distribution on the sparse vector and its support with a distribution from an exponential family. The approximate distribution is then used for direct estimation of the channel. The EP algorithm assumes that the model parameters are known a priori. Since these parameters are unknown, we estimate these parameters using the expectation maximization (EM) algorithm. The combination of EM and EP referred to as EM-EP algorithm is reminiscent of the variational EM approach. Simulation results show that the proposed EM-EP algorithm outperforms several recently-proposed algorithms in the literature.
A clustered base transceiver station (BTS) coordination strategy is proposed for a large cellular MIMO network, which includes full intra-cluster coordination to enhance the sum rate and limited inter-cluster coordination to reduce interference for the cluster edge users. Multi-cell block diagonalization is used to coordinate the transmissions across multiple BTSs in the same cluster. To satisfy per-BTS power constraints, three combined precoder and power allocation algorithms are proposed with different performance and complexity tradeoffs. For inter-cluster coordination, the coordination are…
The use of mmWave frequencies is one of the key strategies to achieve the fascinating 1000x increase in the capacity of future 5G wireless systems. While for traditional sub-6 GHz cellular frequencies several well-developed statistical channel models are available for system simulation, similar tools are not available for mmWave frequencies, thus preventing a fair comparison of independently developed transmission and reception schemes. In this paper we provide a simple albeit accurate statistical procedure for the generation of a clustered MIMO channel model operating at mmWaves, for both the…
We investigate achievable degrees of freedom (DoF) for a multiple-input multiple-output (MIMO) multiway relay channel (mRC) with $L$ clusters and $K$ users per cluster. Each user is equipped with $M$ antennas and the relay with $N$ antennas. We assume a new data exchange model, termed \emph{clustered full data exchange}, i.e., each user in a cluster wants to learn the messages of all the other users in the same cluster. Novel signal alignment techniques are developed to systematically construct the beamforming matrices at the users and the relay for efficient physical-layer network coding. Bas…
The optimal design of aperiodic/irregular clustered phased arrays for base stations (BSs) in multi-user multiple-input multiple-output (MU-MIMO) communication systems is addressed. The paper proposes an ad-hoc synthesis method aimed at maximizing the users traffic capacity within the cell served by the BS, while guaranteeing the sufficient level of signal at the terminals. Towards this end, the search of the optimal aperiodic clustering is carried out through a customized tiling technique able to consider both single and multiple tile shapes as well as to assure the complete coverage of the an…
We take a new perspective on the weighted sum-rate maximization in multiple-input multiple-output (MIMO) interference networks, by formulating an equivalent max-min problem. This seemingly trivial reformulation has significant implications: the Lagrangian duality of the equivalent max-min problem provides an elegant way to establish the sum-rate duality between an interference network and its reciprocal when such a duality exists, and more importantly, suggests a novel iterative minimax algorithm for the weighted sum-rate maximization. Moreover, the design and convergence proof of the algorith…
This paper develops a novel approach to obtaining the optimal scheduling strategy in a multi-input multi-output (MIMO) multi-access channel (MAC), where each transmitter is powered by an individual energy harvesting process. Relying on the state-of-the-art convex optimization tools, the proposed approach provides a low-complexity block coordinate ascent algorithm to obtain the optimal transmission policy that maximizes the weighted sum-throughput for MIMO MAC. The proposed approach can provide the optimal benchmarks for all practical schemes in energy-harvesting powered MIMO MAC transmissions.…
MIMO interference network optimization is important for increasingly crowded wireless communication networks. We provide a new algorithm, named Dual Link algorithm, for the classic problem of weighted sum-rate maximization for MIMO multiaccess channels (MAC), broadcast channels (BC), and general MIMO interference channels with Gaussian input and a total power constraint. For MIMO MAC/BC, the algorithm finds optimal signals to achieve the capacity region boundary. For interference channels with Gaussian input assumption, two of the previous state-of-the-art algorithms are the WMMSE algorithm an…
We consider the problem of maximizing the harvested power in Multiple Input Multiple Output (MIMO) Simultaneous Wireless Information and Power Transfer (SWIPT) systems with power splitting reception. Different from recently proposed designs, we target with our novel problem formulation at the jointly optimal transmit precoding and receive uniform power splitting (UPS) ratio maximizing the harvested power, while ensuring that the Quality-of-Service (QoS) requirement of the MIMO link is satisfied. We assume generic practical Radio Frequency (RF) Energy Harvesting (EH) receive operation that resu…
This paper investigates the joint data and pilot power optimization for maximum sum spectral efficiency (SE) in multi-cell Massive MIMO systems, which is a non-convex problem. We first propose a new optimization algorithm, inspired by the weighted minimum mean square error (MMSE) approach, to obtain a stationary point in polynomial time. We then use this algorithm together with deep learning to train a convolutional neural network to perform the joint data and pilot power control in sub-millisecond runtime, making it suitable for online optimization in real multi-cell Massive MIMO systems. The…
Adopting one-bit analog-to-digital convertors (ADCs) for massive multiple-input multiple-output (MIMO) implementations has great potential in reducing the hardware cost and power consumption. However, distortions caused by quantization raise great challenges. In MIMO orthogonal frequency-division modulation (OFDM) detection, coarse quantization renders the orthogonal separation among subcarriers inapplicable, forcing us to deal with a problem that has a very large problem size. In this paper we study the expectation-maximization (EM) approach for one-bit MIMO-OFDM detection. The idea is to ite…
In this paper, we consider linear MIMO transceiver design for a cellular two-way amplify-and-forward relaying system consisting of a single multi-antenna base station, a single multi-antenna relay station, and multiple multi-antenna mobile stations (MSs). Due to the two-way transmission, the MSs could suffer from tremendous multi-user interference. We apply an interference management model exploiting signal space alignment and propose a transceiver design algorithm, which allows for alleviating the loss in spectral efficiency due to half-duplex operation and providing flexible performance opti…
We propose an algorithm to maximize the instantaneous sum data rate transmitted by a base station in the downlink of a multiuser multiple-input, multiple-output system. The transmitter and the receivers may each be equipped with multiple antennas and each user may receive more than one data stream. We show that maximizing the sum rate is closely linked to minimizing the product of mean squared errors (PMSE). The algorithm employs an uplink/downlink duality to iteratively design transmit-receive linear precoders, decoders, and power allocations that minimize the PMSE for all data streams under …
Reducing computational complexity is crucial in optimizing the phase shifts of Intelligent Reflecting Surface (IRS) systems since IRS-assisted communication systems are generally deployed with a large number of reflecting elements (REs). This letter proposes a low-complexity algorithm, designated as Dimension-wise Sinusoidal Maximization (DSM), to obtain the optimal IRS phase shifts that maximize the sum capacity of a MIMO network. The algorithm exploits the fact that the objective function for the optimization problem is sinusoidal w.r.t. the phase shift of each RE. The numerical results show…
This paper considers distributed linear beamforming in downlink multicell multiuser orthogonal frequency-division multiple access networks. A fast convergent solution maximizing the weighted sum- rate with per base station (BS) transmiting power constraint is formulated. We approximate the non- convex weighted sum-rate maximization (WSRM) problem with a semidefinite relaxed solvable convex form by means of a series of approximation based on interference alignment (IA) analysis. The WSRM optimization is a two-stage optimization process. In the first stage, the IA conditions are satisfied. In th…
In this paper we address a sum secrecy rate maximization problem for a multi-carrier and MIMO communication system. We consider the case that the receiver is capable of full-duplex (FD) operation and simultaneously sends jamming signal to a potential eavesdropper. In particular, we simultaneously take advantage of the spatial and frequency diversity in the system in order to obtain a higher level of security in the physical layer. Due to the non-convex nature of the resulting mathematical problem, we propose an iterative solution with a guaranteed convergence, based on block coordinate descent…
The limited fronthaul capacity is known to be one of the main problems in cloud radio access networks (CRANs), especially in the wireless fronthaul links. In this paper, we consider the uplink of a CRAN system, where massive multiple-input multiple-output (MIMO) is utilized in the fronthaul link. Considering multi-antenna user equipment (UEs) and multi-antenna remote radio heads (RRHs), we maximize the system sum-rate by jointly optimizing the precoders at the UEs and the quantization noise covariance matrices and transmit powers at the RRHs. To solve the resulting nonconvex problem, an iterat…
Joint Transceiver Orientation Optimization for Rotatable-Antenna MIMO Capacity Maximization
School of Information Science and Electronic Engineering, Shanghai Jiao Tong University（上海交通大学信息科学与电子工程学院）；State Key Laboratory of Internet of Things for Smart City and the Department of Electrical and Computer Engineering, University of Macau（澳门大学物联网智能城市国家重点实验室及电气与计算机工程系）
This paper investigates a reconfigurable intelligent surface (RIS)-aided multi-user multiple-input multiple-output (MIMO) system by considering only the statistical channel state information (CSI) at the base station (BS). We aim to maximize its sum-rate via the joint optimization of beamforming at the BS and phase shifts at the RIS. However, the multi-user MIMO transmissions and the spatial correlations make the optimization cumbersome. For tractability, a deterministic approximation is derived for the sum-rate under a large number of the reflecting elements. By adopting the approximate sum-r…
One basic operation of Internet-of-Things (IoT) networks is aggregating distributed sensing-data over wireless-channels for function-computation, called wireless-data-aggregation (WDA). Targeting dense sensors, a recently developed technology called over-the-air computing (AirComp) can dramatically reduce the WDA latency by aggregating distributed data "over-the-air" using the waveform-superposition property of a multi-access channel. In this work, we design multiple-input-multiple-output (MIMO) AirComp for computing a vector-valued function in a clustered IoT network with multi-antenna sensor…
Reconfigurable multiple-input multiple-output can provide performance gains over traditional MIMO by reshaping the channels, i.e., introducing more channel realizations. In this paper, we focus on the achievable rate maximization pattern design for reconfigurable MIMO systems. Firstly, we introduce the matrix representation of pattern reconfigurable MIMO (PR-MIMO), based on which a pattern design problem is formulated. To further reveal the effect of the radiation pattern on the wireless channel, we consider pattern design for both the single-pattern case where the optimized radiation pattern …
An upper bound on the ergodic capacity of {\bf MIMO} channels was introduced recently in arXiv:0903.1952. This upper bound amounts to the maximization on the simplex of some multilinear polynomial $p(λ_1,...,λ_n)$ with non-negative coefficients. Interestingly, the coefficients are subpermanents of some non-negative matrix. In general, such maximizations problems are {\bf NP-HARD}. But if say, the functional $\log(p)$ is concave on the simplex and can be efficiently evaluated, then the maximization can also be done efficiently. Such log-concavity was conjectured in arXiv:0903.1952. We give in t…
This paper investigates the transceiver design problem in a noisy-sensing noisy-transmission multi-input multi-output (MIMO) wireless sensor network. Consider a cluster-based network, where multiple sensors scattering across several clusters will first send their noisy observations to their respective cluster-heads (CH), who will then forward the data to one common fusion center (FC). The cluster-heads and the fusion center collectively form a coherent-sum multiple access channel (MAC) that is affected by fading and additive noise. Our goal is to jointly design the linear transceivers at the C…
Recently, intelligent reflecting surface (IRS) has emerged as an appealing technique that enables wireless communications with low hardware cost and low power consumption. In this letter, we consider an IRS-assisted point-to-point multi-input multi-output (MIMO) system, where a source communicates with its destination with the help of an IRS. Our goal is to maximize the spectral efficiency of this system by jointly optimizing the (active) precoding at the source and the (passive) phase shifters (PSs) at the IRS. However, this turns out to be an intractable mixed integer non-convex optimization…
This paper considers the fundamental power allocation problem in cell-free massive mutiple-input and multiple-output (MIMO) systems which aims at maximizing the total energy efficiency (EE) under a sum power constraint at each access point (AP) and a quality-of-service (QoS) constraint at each user. Existing solutions for this optimization problem are based on solving a sequence of second-order cone programs (SOCPs), whose computational complexity scales dramatically with the network size. Therefore, they are not implementable for practical large-scale cell-free massive MIMO systems. To tackle…
We consider the problem of maximizing the harvested power in Multiple Input Multiple Output (MIMO) Simultaneous Wireless Information and Power Transfer (SWIPT) systems with power splitting reception. Different from recently proposed designs, with our optimization problem formulation we target for the jointly optimal transmit precoding and receive uniform power splitting (UPS) ratio maximizing the harvested power, while ensuring that the quality-of-service requirement of the MIMO link is satisfied. We assume practical Radio-Frequency (RF) energy harvesting (EH) receive operation that results in…
To achieve perfect secrecy in a multiple-input multiple-output (MIMO) Gaussian wiretap channel (WTC), we need to find its secrecy capacity and optimal signaling, which involves solving a difference of convex functions program known to be non-convex for the non-degraded case. To deal with this, a class of existing solutions have been developed but only local optimality is guaranteed by standard convergence analysis. Interestingly, our extensive numerical experiments have shown that these local optimization methods indeed achieve global optimality. In this paper, we provide an analytical proof f…
Reconfigurable intelligent surface (RIS) has recently drawn intensive attention due to its potential of simultaneously realizing high spectral and energy efficiency in a sustainable way. This paper focuses on the design of efficient transmission methods to maximize the uplink sum throughput in a RIS-aided multi-user multi-input multi-output (MU-MIMO) system. To provide an insightful basis, the channel capacity of RIS-aided MU-MIMO is theoretically analyzed. Then, the conventional transmission schemes based on orthogonal multiple access are presented as the baseline. From the information-theore…
Intelligent reflecting surface (IRS) is a promising technology to extend the wireless signal coverage and support the high performance communication. By intelligently adjusting the reflection coefficients of a large number of passive reflecting elements, the IRS can modify the wireless propagation environment in favour of signal transmission. Different from most of the prior works which did not consider any cooperation between IRSs, in this work we propose and study a cooperative double-IRS aided multiple-input multiple-output (MIMO) communication system under the line-of-sight (LoS) propagati…
Interference management is a fundamental issue in device-to-device (D2D) communications whenever the transmitter-and-receiver pairs are located in close proximity and frequencies are fully reused, so active links may severely interfere with each other. This paper devises an optimization strategy named FPLinQ to coordinate the link scheduling decisions among the interfering links, along with power control and beamforming. The key enabler is a novel optimization method called matrix fractional programming (FP) that generalizes previous scalar and vector forms of FP in allowing multiple data stre…
Massive multi-input multiple-out (MIMO) is a key ingredient in improving the spectral efficiencies for next-generation cellular systems. Thanks to the channel reciprocity, in time-division-duplexing mode, each base station (BS) can acquire local channel state information at the transmitter (CSIT) for a set of users possibly located in adjacent cells. When the small cell BSs equipped with not-so-many antennas are densely deployed with marcrocells, a simple noncooperative MIMO precoding technique using local CSIT fails to achieve high spectral efficiency because of strong inter-cell-interference…
Intelligent reflecting surface (IRS) has gained tremendous attention recently as a disruptive technology for beyond 5G networks. In this paper, we consider the problem of secrecy rate maximization for an IRS-assisted Gaussian multiple-input multiple-output multi-antenna-eavesdropper (MIMOME) wiretap channel (WTC). In this context, we aim to jointly optimize the input covariance matrix and the IRS phase shifts to maximize the achievable secrecy rate of the considered system. To solve the formulated problem which is non-convex, we propose an iterative method based on the block successive maximiz…
Physical-layer key generation (PKG) based on channel reciprocity has recently emerged as a new technique to establish secret keys between devices. Most works focus on pairwise communication scenarios with single or small-scale antennas. However, the fifth generation (5G) wireless communications employ massive multiple-input multiple-output (MIMO) to support multiple users simultaneously, bringing serious overhead of reciprocal channel acquisition. This paper presents a multi-user secret key generation in massive MIMO wireless networks. We provide a beam domain channel model, in which different…
In this work, a MIMO broadcast channel under the energy harvesting (EH) constraint and the peak power constraint is investigated. The transmitter is equipped with a hybrid energy storage system consisting of a perfect super capacitor (SC) and an inefficient battery, where both elements have limited energy storage capacities. In addition, the effect of data processing circuit power consumption is also addressed. To be specific, two extreme cases are studied here, where the first assumes ideal/zero circuit power consumption and the second considers a positive constant circuit power consumption w…
Reconfigurable Intelligent Surfaces (RISs) are an emerging technology for future wireless communication systems, enabling improved coverage in an energy efficient manner. RISs are usually metasurfaces, constituting of two-dimensional arrangements of metamaterial elements, whose individual response is commonly modeled in the literature as an adjustable phase shifter. However, this model holds only for narrowband communications, and when wideband transmissions are utilized, one has to account for the frequency selectivity of metamaterials, whose response usually follows a Lorentzian-like profile…
The hybrid relay-reflecting intelligent surface (HR-RIS) has been recently introduced as an efficient solution to overcome the double path loss and limited beamforming diversity of the conventional fully passive reflecting surface. This motivates us to investigate the application of the HR-RIS in improving the secrecy capacity of millimeter wave multiple-input-multiple-output (MIMO) systems with the presence of multi-antenna eavesdropper. The joint optimization of the transmit beamformer and the relay-reflecting coefficients at RIS is tackled via alternating optimization. In the proposed solut…
We consider the problem of linear transceiver design to achieve max-min fairness in a downlink MIMO multicell network. This problem can be formulated as maximizing the minimum rate among all the users in an interfering broadcast channel (IBC). In this paper we show that when the number of antennas is at least two at each of the transmitters and the receivers, the min rate maximization problem is NP-hard in the number of users. Moreover, we develop a low-complexity algorithm for this problem by iteratively solving a sequence of convex subproblems, and establish its global convergence to a stati…
MIMO systems in the lower part of the millimeter-wave spectrum band (i.e., below 28 GHz) do not exhibit enough directivity and selectively, as their counterparts in higher bands of the spectrum (i.e., above 60 GHz), and thus still suffer from the detrimental effect of interference, on the system sum-rate. As such systems exhibit large numbers of antennas and short coherence times for the channel, traditional methods of distributed coordination are ill-suited, and the resulting communication overhead would offset the gains of coordination. In this work, we propose algorithms for tackling the su…
Designing an efficient scheme in physical layer enables cognitive radio (CR) users to efficiently utilize resources dedicated to primary users (PUs). In this paper in order to maximize the SU's throughput, the SU's transceivers beamforming is designed through new model considering the presence of the PU's transmitter. Since presence of primary transmitter basically degrades CR's system performance; proposed beamforming design considers intra-system interference between PUs and SUs. An optimization problem based on maximizing CR network throughput subject to controlling interference power from …
Sum-rate maximization in two-way amplify-and-forward (AF) multiple-input multiple-output (MIMO) relaying belongs to the class of difference-of-convex functions (DC) programming problems. DC programming problems occur as well in other signal processing applications and are typically solved using different modifications of the branch-and-bound method. This method, however, does not have any polynomial time complexity guarantees. In this paper, we show that a class of DC programming problems, to which the sum-rate maximization in two-way MIMO relaying belongs, can be solved very efficiently in po…
The cell-free MIMO concept relying on hybrid precoding constitutes an innovative technique capable of dramatically increasing the network capacity of millimeter-wave (mmWave) communication systems. It dispenses with the cell boundary of conventional multi-cell MIMO systems, while drastically reducing the power consumption by limiting the number of radio frequency (RF) chains at the access points (APs). In this paper, we aim for maximizing the weighted sum rate (WSR) of mmWave cell-free MIMO systems by conceiving a low-complexity hybrid precoding algorithm. We formulate the WSR optimization pro…
Optimal signaling for secrecy rate maximization in Gaussian MIMO wiretap channels is considered. While this channel has attracted a significant attention recently and a number of results have been obtained, including the proof of the optimality of Gaussian signalling, an optimal transmit covariance matrix is known for some special cases only and the general case remains an open problem. An iterative custom-made algorithm to find a globally-optimal transmit covariance matrix in the general case is developed in this paper, with guaranteed convergence to a \textit{global} optimum. While the origi…
Driven by green communications, energy efficiency (EE) has become a new important criterion for designing wireless communication systems. However, high EE often leads to low spectral efficiency (SE), which spurs the research on EE-SE tradeoff. In this paper, we focus on how to maximize the utility in physical layer for an uplink multi-user multiple-input multipleoutput (MU-MIMO) system, where we will not only consider EE-SE tradeoff in a unified way, but also ensure user fairness. We first formulate the utility maximization problem, but it turns out to be non-convex. By exploiting the structur…
A multiple-antenna amplify-and-forward two-hop interference network with multiple links and multiple relays is considered. We optimize transmit precoders, receive decoders and relay AF matrices to maximize the achievable sum rate. Under per user and total relay sum power constraints, we propose an efficient algorithm to maximize the total signal to total interference plus noise ratio (TSTINR). Computational complexity analysis shows that our proposed algorithm for TSTINR has lower complexity than the existing weighted minimum mean square error (WMMSE) algorithm. We analyze and confirm by simul…
