We report on the quantitative experimental illustration of elementary optomechanics within the classical regime. All measurements are performed in a commercial dilution refrigerator on a mesoscopic drumhead aluminium resonator strongly coupled to a microwave cavity, using only strict single-tone schemes. Sideband asymmetry is reported using in-cavity microwave pumping, along with noise squashing and back-action effects. Results presented in this paper are analysed within the simple classical electric circuit theory, emphasizing the analogous nature of classical features with respect to their usual quantum description. The agreement with theory is obtained with no fitting parameters. Besides, based on those results a simple method is proposed for the accurate measurement of the ratio between microwave internal losses and external coupling.
We have developed a novel architecture for room temperature microwave cavity optomechanics, which is based on the coupling of a 3D microwave reentrant cavity to a compliant membrane. Devices parameters have enabled resolving the thermomechanical motion of the membrane, and observing optomechanically induced transparency/absorption in the linear regime, for the first time in a microwave optomechanical system operated at room temperature. We have extracted the single photon coupling rate (g0) using four independent measurement techniques, and hence obtain a full characterization of the proposed …
The combination of low mass density, high frequency, and high quality-factor of mechanical resonators made of two-dimensional crystals such as graphene make them attractive for applications in force sensing/mass sensing, and exploring the quantum regime of mechanical motion. Microwave optomechanics with superconducting cavities offers exquisite position sensitivity and enables the preparation and detection of mechanical systems in the quantum ground state. Here, we demonstrate coupling between a multilayer graphene resonator with quality factors up to 220,000 and a high-$\textit{Q}$ supercondu…
Cavity optomechanics has served as a platform for studying the interaction between light and micromechanical motion via radiation pressure. Here we observe such phenomena with a graphene mechanical resonator coupled to an electromagnetic mode. We measure thermal motion and back-action cooling in a bilayer graphene resonator coupled to a microwave on-chip cavity. We detect the lowest flexural mode at 24 MHz down to 50 mK, corresponding to roughly mechanical 40 quanta, representing nearly three orders of magnitude lower phonon occupation than recorded to date with graphene resonators.
The motion of micro- and nanomechanical resonators can be coupled to electromagnetic fields. This allows to explore the mutual interaction and introduces new means to manipulate and control both light and mechanical motion. Such optomechanical systems have recently been implemented in nanoelectromechanical systems involving a nanomechanical beam coupled to a superconducting microwave resonator. Here, we propose optomechanical systems that involve multiple, coupled microwave resonators. In contrast to similar systems in the optical realm, the coupling frequency governing photon exchange between…
The mechanical properties of amorphous materials (glasses) at low temperatures are dominated by effects of low energy excitations that are thought to be atomic-scale tunneling two level systems (TTLS). In nanometer-scale glass samples, the temperature dependence of the sound speed and dissipation is modified relative to that of bulk glass samples. In addition to this size effect, the usual presence of a polycrystalline metal in nanomechanical resonators leads to a further departure from the well-studied behavior of insulating bulk glass. We report a dual chip optomechanical measurement techniq…
Directional transmission or amplification of microwave signals is indispensable in various applications involving sensitive measurements. In this work we show in experiment how to use a generic cavity optomechanical setup to non-reciprocally amplify microwave signals above 3 GHz in one direction by 9 decibels, and simultaneously attenuate the transmission in the opposite direction by 21 decibels. We use a device including two on-chip superconducting resonators and two metallic drumhead mechanical oscillators. Application of four microwave pump tone frequencies allows for designing constructive…
High-gain and low-noise signal amplification is a valuable tool in various cryogenic microwave experiments. A microwave optomechanical device, in which a vibrating capacitor modulates the frequency of a microwave cavity, is one technique that is able to amplify microwave signals with high gain and large dynamical range. Such optomechanical amplifiers typically rely on strong backaction of microwave photons on the mechanical mode achieved in the sideband-resolved limit of optomechanics. Here, we observe microwave amplification in an optomechanical cavity in the extremely unresolved sideband lim…
We present a cavity piezo-optomechanical system where microwave and optical degrees of freedom are coupled through an ultra-high frequency mechanical resonator. By utilizing the coherence among the three interacting modes, we demonstrate optical amplification, coherent absorption and a more general asymmetric Fano resonance. The strong piezoelectric drive further allows access to the large-amplitude-induced optomechanical nonlinearity, with which optical transparency at higher harmonics through multi-phonon scattering is demonstrated.
We report on microwave optomechanics measurements performed on a nuclear adiabatic demagnetization cryostat, whose temperature is determined by accurate thermometry from below 500$~μ$K to about 1$~$Kelvin. We describe a method for accessing the on-chip temperature, building on the blue-detuned parametric instability and a standard microwave setup. The capabilities and sensitivity of both the experimental arrangement and the developed technique are demonstrated with a very weakly coupled silicon-nitride doubly-clamped beam mode of about 4$~$MHz and a niobium on-chip cavity resonating around 6$~…
We study theoretically a three-mode optomechanical system where two mechanical oscillators are independently coupled to a single cavity mode. By optimized two-tone or four-tone driving of the cavity one can prepare the mechanical oscillators in an entangled two-mode squeezed state, even if they start in a thermal state. The highly-pure, symmetric steady-state achieved allows the optimal fidelity of standard continuous-variable teleportation protocols to be achieved. In contrast to other reservoir engineering approaches to generating mechanical entanglement, only a single reservoir is required …
Microwave to optical transduction has received a great deal of interest from the cavity optomechanics community as a landmark application for electro-optomechanical systems. In this Letter, we demonstrate a novel transducer that combines high-frequency mechanical motion and a microwave cavity for the first time. The system consists of a 3D microwave cavity and a gallium arsenide optomechanical crystal, which has been placed in the microwave electric field maximum. This allows the microwave cavity to actuate the gigahertz-frequency mechanical breathing mode in the optomechanical crystal through…
In recent years, the field of microwave optomechanics has emerged as leading platform for achieving quantum control of macroscopic mechanical objects. Implementations of microwave optomechanics to date have coupled microwave photons to mechanical resonators using a moving capacitance. While simple and effective, the capacitive scheme suffers from inherent and practical limitations on the maximum achievable coupling strength. Here, we experimentally implement a fundamentally different approach: flux-mediated optomechanical coupling. In this scheme, mechanical displacements modulate the flux in …
We explore the nonlinear dynamics of a cavity optomechanical system. Our realization consisting of a drumhead nano-electro-mechanical resonator (NEMS) coupled to a microwave cavity, allows for a nearly ideal platform to study the nonlinearities arising purely due to radiation-pressure physics. Experiments are performed under a strong microwave Stokes pumping which triggers mechanical self-sustained oscillations. We analyze the results in the framework of an extended nonlinear optomechanical theory, and demonstrate that quadratic and cubic coupling terms in the opto-mechanical Hamiltonian have …
We report on the generic classical electric circuit modeling that describes standard single-tone microwave optomechanics. Based on a parallel RLC circuit in which a mechanical oscillator acts as a movable capacitor, derivations of analytical expressions are presented, including key features such as the back-action force, the input-output expressions, and the spectral densities associated, all in the classical regime. These expressions coincide with the standard quantum treatment performed in optomechanics when the occupation number of both cavity and mechanical oscillator are large. Besides, t…
We experimentally study an optomechanical cavity consisting of an oscillating mechanical resonator embedded in a superconducting microwave transmission line cavity. Tunable optomechanical coupling between the mechanical resonator and the microwave cavity is introduced by positioning a niobium-coated single mode optical fiber above the mechanical resonator. The capacitance between the mechanical resonator and the coated fiber gives rise to optomechanical coupling, which can be controlled by varying the fiber-resonator distance. We study radiation pressure induced self-excited oscillations as a …
We investigate a general scheme for generating, either dynamically or in the steady state, continuous variable entanglement between two mechanical resonators with different frequencies. We employ an optomechanical system in which a single optical cavity mode driven by a suitably chosen two-tone field is coupled to the two resonators. Significantly large mechanical entanglement can be achieved, which is extremely robust with respect to temperature.
Owing to ever increasing gate fidelities and to a potential transferability to industrial CMOS technology, silicon spin qubits have become a compelling option in the strive for quantum computation. In a scalable architecture, each spin qubit will have to be finely tuned and its operating conditions accurately determined. In this prospect, spectroscopic tools compatible with a scalable device layout are of primary importance. Here we report a two-tone spectroscopy technique providing access to the spin-dependent energy-level spectrum of a hole double quantum dot defined in a split-gate silicon …
Mechanical resonators are macroscopic quantum objects with great potential. They couple to many different quantum systems such as spins, optical photons, cold atoms, and Bose Einstein condensates. It is however difficult to measure and manipulate the phonon state due to the tiny motion in the quantum regime. On the other hand, microwave resonators are powerful quantum devices since arbitrary photon state can be synthesized and measured with a quantum tomography. We show that a linear coupling, strong and controlled with a gate voltage, between the mechanical and the microwave resonators enable…
Cavity optomechanics is a tool to study the interaction between light and micromechanical motion. Here we observe near-quantum limited optomechanical physics in a truly macroscopic oscillator. As the mechanical system, we use a mm-sized piezoelectric quartz disk oscillator. Its motion is coupled to a charge qubit which translates the piezo-induced charge into an effective radiation-pressure interaction between the disk and a microwave cavity. We measure the thermal motion of the lowest mechanical shear mode at 7MHz down to 35 mK, corresponding to roughly 100 quanta in a 20mg oscillator. The wo…
We measure the fundamental noise processes associated with a continuous linear position measurement of a micromechanical membrane incorporated in a microwave cavity optomechanical circuit. We observe the trade-off between the two fundamental sources of noises that enforce the standard quantum limit: the measurement imprecision and radiation-pressure backaction from photon shot noise. We demonstrate that the quantum backaction of the measurement can overwhelm the intrinsic thermal motion by 24 dB, entering a new regime for cavity optomechanical systems.
Cavity optomechanics allows the characterization of a vibration mode, its cooling and quantum manipulation using electromagnetic fields. Regarding nanomechanical as well as electronic properties, single wall carbon nanotubes are a prototypical experimental system. At cryogenic temperatures, as high quality factor vibrational resonators, they display strong interaction between motion and single-electron tunneling. Here, we demonstrate large optomechanical coupling of a suspended carbon nanotube quantum dot and a microwave cavity, amplified by several orders of magnitude via the nonlinearity of …
Graphene is an attractive material for nanomechanical devices because it allows for exceptional properties, such as high frequencies and quality factors, and low mass. An outstanding challenge, however, has been to obtain large coupling between the motion and external systems for efficient readout and manipulation. Here, we report on a novel approach, in which we capacitively couple a high-Q graphene mechanical resonator ($Q \sim 10^5$) to a superconducting microwave cavity. The initial devices exhibit a large single-photon coupling of $\sim 10$ Hz. Remarkably, we can electrostatically change …
We study theoretically a three-mode optomechanical system where two mechanical oscillators are coupled to a single cavity mode. By using two-tone (i.e. amplitude-modulated) driving of the cavity, it is possible to couple the cavity to a single collective quadrature of the mechanical oscillators. In such a way, a back-action-evading measurement of the collective mechanical quadrature is possible. We discuss how this can allow one to measure both quadratures of a mechanical force beyond the full quantum limit, paying close attention to the role of dissipation and experimental imperfections. We a…
The field of cavity optomechanics has achieved groundbreaking photonic control and detection of mechanical oscillators, based on their coupling to linear electromagnetic modes. Lately, however, there is an uprising interest in exploring cavity nonlinearities as a powerful new resource in radiation-pressure interacting systems. Here, we present a flux-mediated optomechanical device combining a nonlinear Josephson-based superconducting quantum interference cavity with a mechanical nanobeam. We demonstrate how the intrinsic Kerr nonlinearity of the microwave circuit can be used for a counter-intu…
Electrically actuated optomechanical resonators provide a route to quantum-coherent, bidirectional conversion of microwave and optical photons. Such devices could enable optical interconnection of quantum computers based on qubits operating at microwave frequencies. Here we present a novel platform for microwave-to-optical conversion comprising a photonic crystal cavity made of single-crystal, piezoelectric gallium phosphide integrated on pre-fabricated niobium circuits on an intrinsic silicon substrate. The devices exploit spatially extended, sideband-resolved mechanical breathing modes at $\…
Microwave optomechanical circuits have been demonstrated in the past years to be extremely powerfool tools for both, exploring fundamental physics of macroscopic mechanical oscillators as well as being promising candidates for novel on-chip quantum limited microwave devices. In most experiments so far, the mechanical oscillator is either used as a passive device element and its displacement is detected using the superconducting cavity or manipulated by intracavity fields. Here, we explore the possibility to directly and parametrically manipulate the mechanical nanobeam resonator of a cavity el…
Directional amplifiers are an important resource in quantum information processing, as they protect sensitive quantum systems from excess noise. Here, we propose an implementation of phase-preserving and phase-sensitive directional amplifiers for microwave signals in an electromechanical setup comprising two microwave cavities and two mechanical resonators. We show that both can reach their respective quantum limits on added noise. In the reverse direction, they emit thermal noise stemming from the mechanical resonators and we discuss how this noise can be suppressed, a crucial aspect for tech…
Using a superconducting circuit, the Josephson mixer, we demonstrate the first experimental realization of spatially separated two-mode squeezed states of microwave light. Driven by a pump tone, a first Josephson mixer generates, out of quantum vacuum, a pair of entangled fields at different frequencies on separate transmission lines. A second mixer, driven by a $π$-phase shifted copy of the first pump tone, recombines and disentangles the two fields. The resulting output noise level is measured to be lower than for vacuum state at the input of the second mixer, an unambiguous proof of entangl…
We propose a superconducting circuit comprising a dc-SQUID with mechanically compliant arm embedded in a coplanar microwave cavity that realizes an optomechanical system with a degenerate or non-degenerate parametric interaction generated via the dynamical Casimir effect. For experimentally feasible parameters, this setup is capable of reaching the single-photon, ultra-strong coupling regime, while simultaneously possessing a parametric coupling strength approaching the renormalized cavity frequency. This opens up the possibility of observing the interplay between these two fundamental nonline…
Josephson junctions based on semiconductor nanowires are potential building blocks for electrically tunable qubit structures, e.g. the gatemon or the Andreev qubit. However, an actual realization requires the thorough investigation of the intrinsic excitation spectrum. Here, we demonstrate the fabrication of low-loss superconducting microwave circuits that combine high quality factors with a well-controlled gate architecture by utilizing a flip-chip approach. This platform is then used to perform single-tone and two-tone experiments on Andreev states in in-situ grown InAs/Al core/half-shell na…
A detailed analysis of electromechanically induced absorption (EMIA) in a circuit nano-electromechanical hybrid system consisting of a superconducting microwave resonator coupled to a nanomechanical beam is presented. By performing two-tone spectroscopy experiments we have studied EMIA as a function of the drive power over a wide range of drive and probe tone detunings. We find good quantitative agreement between experiment and theoretical modeling based on the Hamiltonian formulation of a generic electromechanical system. We show that the absorption of microwave signals in an extremely narrow…
In cavity optomechanics, light is used to control mechanical motion. A central goal of the field is achieving single-photon strong coupling, which would enable the creation of quantum superposition states of motion. Reaching this limit requires significant improvements in optomechanical coupling and cavity coherence. Here we introduce an optomechanical architecture consisting of a silicon nitride membrane coupled to a three-dimensional superconducting microwave cavity. Exploiting their large quality factors, we achieve an optomechanical cooperativity of 146,000 and perform sideband cooling of …
At low temperatures, microwave cavities are often preferred for the readout and control of a variety of systems. In this paper, we present design and measurements on an optomechanical device based on a 3-dimensional rectangular waveguide cavity. We show that by suitably modifying the electromagnetic field corresponding to the fundamental mode of the cavity, the equivalent circuit capacitance can be reduced to 29 fF. By coupling a mechanical resonator to the modified electromagnetic mode of the cavity, we achieved a capacitance participation ratio of 43 $\%$. We demonstrate an optomechanical co…
Cavity optomechanical phenomena, such as cooling, amplification or optomechanically induced transparency, emerge due to a strong imbalance in the dissipation rates of the parametrically coupled electromagnetic and mechanical resonators. Here we analyze the reversed dissipation regime where the mechanical energy relaxation rate exceeds the energy decay rate of the electromagnetic cavity. We demonstrate that this regime allows for mechanically-induced amplification (or cooling) of the electromagnetic mode. Gain, bandwidth, and added noise of this electromagnetic amplifier are derived and compare…
