Millimeter wave (mmWave) communication represents one of the main innovations of the next generation of wireless technologies, allowing users to reach unprecedented data rates. To overcome the high path loss at mmWave frequencies, these systems make use of directional antennas able to focus the transmit power into narrow beams using BeamForming (BF) techniques, thus making the communication directional. This new paradigm opens up a set of challenges for the design of efficient wireless systems, in which antenna and BF components play an important role also at the higher layer of the protocol stack. For this reason, accurate modeling of these components in a full-stack simulation is of primary importance to understand the overall system behavior. This paper proposes a novel framework for the end-to-end simulation of 5G mmWave cellular networks, including a ray-tracing based channel model and accurate models for antenna arrays and BF schemes. We showcase this framework by evaluating the performance of different antenna and BF configurations considering both link-level and end-to-end metrics and present the obtained results.
Hybrid analog and digital beamforming has emerged as a key enabling technology for millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) communication systems since it can balance the trade-off between system performance and hardware efficiency. Owing to the strong ability of central control, cooperative networks show great potential to enhance the spectral efficiency of mmWave communications. In this paper, we consider cooperative mmWave MIMO systems and propose user association and hybrid beamforming design algorithms for three typical hybrid beamforming architectures. The c…
Analog beamforming is the predominant approach for millimeter wave (mmWave) communication given its favorable characteristics for limited-resource devices. In this work, we aim at reducing the spectral efficiency gap between analog and digital beamforming methods. We propose a method for refined beam selection based on the estimated raw channel. The channel estimation, an underdetermined problem, is solved using compressed sensing (CS) methods leveraging angular domain sparsity of the channel. To reduce the complexity of CS methods, we propose dictionary learning iterative soft-thresholding al…
Hybrid analog and digital beamforming (HBF) has been recognized as an attractive technique offering a tradeoff between hardware implementation limitation and system performance for future broadband millimeter wave (mmWave) communications. In contrast to most current works focusing on the HBF design for orthogonal frequency division multiplexing based mmWave systems, this paper investigates the HBF design for single carrier (SC) systems due to the advantage of low peak-to-average power ratio in transmissions. By applying the alternating minimization method, we propose an efficient HBF scheme ba…
Beamforming is one of the key techniques in millimeter wave (mmWave) multi-input multi-output (MIMO) communications. Designing appropriate beamforming not only improves the quality and strength of the received signal, but also can help reduce the interference, consequently enhancing the data rate. In this paper, we propose a distributed multi-agent double deep Q-learning algorithm for beamforming in mmWave MIMO networks, where multiple base stations (BSs) can automatically and dynamically adjust their beams to serve multiple highly-mobile user equipments (UEs). In the analysis, largest receive…
Dynamic metasurface antennas (DMAs) provide a new paradigm to realize large-scale antenna arrays for future wireless systems. In this paper, we study the downlink millimeter wave (mmWave) DMA systems with limited number of radio frequency (RF) chains. By using a specific DMA structure, an equivalent mmWave channel model is first explicitly characterized. Based on that, we propose an effective joint microstrip selection and beamforming scheme to accommodate for the limited number of RF chains. A low-complexity digital beamforming solution with channel gain-based microstrip selection is develope…
Hybrid beamforming is considered a key enabler to realize millimeter wave (mmWave) multiple-input multiple-output (MIMO) communications due to its capability of considerably reducing the number of costly and power-hungry radio frequency chains in the transceiver. However, in mmWave MIMO orthogonal frequency-division multiplexing (MIMO-OFDM) systems, hybrid beamforming design is challenging because the analog precoder and combiner are required to be shared across the whole employed bandwidth. In this paper, we propose closed-form solutions to the problem of designing the analog precoder/combine…
Reconfigurable intelligent surface (RIS) is an attractive technology to improve the transmission rate of millimetre-wave (mmWave) communication systems. The previous {research} on RIS technology mainly focused on improving the transmission rate and security rate of the mmWave communication systems. Since the emergence of RIS technology creates the conditions for generating an intelligent radio environment, it also has potential advantages on improving the localization accuracy of the mmWave communication systems. Deployed on walls and objects, RISs are capable of significantly improving commun…
The wide bandwidths offered at millimeter-wave (mmWave) frequencies have made them an attractive choice for future wireless communication systems. Recent works have presented beamforming strategies for enabling in-band full-duplex (FD) capability at mmWave even under the constraints of hybrid beamforming, extending the exciting possibilities of next-generation wireless. Existing mmWave FD designs, however, do not consider frequency-selective mmWave channels. Wideband communication at mmWave suggests that frequency-selectivity will likely be of concern since communication channels will be on th…
Full-duplex (FD) systems gained enormous attention because of the potential to double the spectral efficiency. In the context of 5G technology, FD systems operating at millimeter-wave (mmWave) frequencies become one of the most promising solutions to further increase the spectral efficiency and reduce the latency. However, such systems are vulnerable to the self-interference (SI) that significantly degrades the performance. To overcome this shortcoming, analog-only beamforming techniques have been developed to mitigate the SI. Because of the huge power consumption, systems operating at mmWave …
As a cost-effective alternative, hybrid analog and digital beamforming architecture is a promising scheme for millimeter wave (mmWave) system. This paper considers two hybrid beamforming architectures, i.e. the partially-connected and fully-connected structures, for mmWave dual-function radar communication (DFRC) system, where the transmitter communicates with the downlink users and detects radar targets simultaneously. The optimization problems are formulated by minimizing a weighted summation of radar and communication performance, subject to constant modulus and power constraints. To tackle…
Mobile edge computing (MEC) and millimeter wave (mmWave) communications are capable of significantly reducing the network's delay and enhancing its capacity. In this paper we investigate a mmWave and device-to-device (D2D) assisted MEC system, in which user A carries out some computational tasks and shares the results with user B with the aid of a base station (BS). We propose a novel two-timescale joint hybrid beamforming and task allocation algorithm to reduce the system latency whilst cut down the required signaling overhead. Specifically, the high-dimensional analog beamforming matrices ar…
Unmanned aerial vehicles (UAVs) have found widespread commercial, civilian, and military applications. Wireless communication has always been one of the core technologies for UAV. However, the communication capacity is becoming a bottleneck for UAV to support more challenging application scenarios. The heavily-occupied sub-6 GHz frequency band is not sufficient to meet the ultra high-data-traffic requirements. The utilization of the millimeter-wave (mmWave) frequency bands is a promising direction for UAV communications, where large antenna arrays can be packed in a small area on the UAV to pe…
In this paper, we propose a beamforming design for dual-functional radar-communication (DFRC) systems at the millimeter wave (mmWave) band, where hybrid beamforming and sub-arrayed MIMO radar techniques are jointly exploited. We assume that a base station (BS) is serving a user equipment (UE) located in a Non-Line-of-Sight (NLoS) channel, which in the meantime actively detects multiple targets located in a Line-of-Sight (LoS) channel. Given the optimal communication beamformer and the desired radar beampattern, we propose to design the analog and digital beamformers under non-convex constant-m…
In this paper, we address the problem of three dimensional beamforming in millimeter wave (mmWave) wireless networks. In particular, we study the impact of base station (BS) antenna tilt angle optimization on the energy efficiency (EE) of mmWave networks under two different scenarios: a homogeneous network consisting of multiple macro base stations (MBSs), and a heterogeneous network where several femto base stations are added within the coverage areas of the MBSs. First, by adopting a stochastic geometry approach, we analyze the coverage probability of both scenarios that incorporate 3DBF. Th…
Analog/digital hybrid beamforming architectures with large-scale antenna arrays have been widely considered in millimeter wave (mmWave) communication systems because they can address the tradeoff between performance and hardware efficiency compared with traditional fully-digital beamforming. Most of the prior work on hybrid beamforming focused on fullyconnected architecture or partially-connected scheme with fixedsubarrays, in which the analog beamformers are usually realized by infinite-resolution phase shifters (PSs). In this paper, we introduce a novel hybrid beamforming architecture with d…
Reconfigurable intelligent surface (RIS) assisted millimeter-wave (mmWave) communication systems relying on hybrid beamforming structures are capable of achieving high spectral efficiency at a low hardware complexity and low power consumption. In this paper, we propose an RIS-assisted mmWave point-to-point system relying on dynamically configured sub-array connected hybrid beamforming structures. More explicitly, an energy-efficient analog beamformer relying on twin-resolution phase shifters is proposed. Then, we conceive a successive interference cancelation (SIC) based method for jointly des…
Beamforming technology is widely used in millimeter wave systems to combat path losses, and beamformers are usually selected from a predefined codebook. Unfortunately, the traditional codebook design neglects the beam squint effect, and this will cause severe performance degradation when the bandwidth is large. In this letter, we consider that a codebook with fixed size is adopted in the wideband beamforming system. First, we analyze how beam squint affects system performance when all beams have the same width. The expression of average spectrum efficiency is derived based on the ideal beam pa…
This work develops LoneSTAR, a novel enabler of full-duplex millimeter wave (mmWave) communication systems through the design of analog beamforming codebooks. LoneSTAR codebooks deliver high beamforming gain and broad coverage while simultaneously reducing the self-interference coupled by transmit and receive beams at a full-duplex mmWave transceiver. Our design framework accomplishes this by tolerating some variability in transmit and receive beamforming gain to strategically shape beams that reject self-interference spatially while accounting for digitally-controlled analog beamforming netwo…
In recent years, there has been extensive research on millimeter-wave (mmWave) communication and on in-band full-duplex (FD) communication, but work on the combination of the two is relatively lacking. FD mmWave systems could offer increased spectral efficiency and decreased latency while also suggesting the redesign of existing mmWave applications. While FD technology has been well-explored for sub-6 GHz systems, the developed methods do not translate well to mmWave. This turns us to a method called beamforming cancellation (BFC), where the highly directional mmWave beams are steered to mitig…
In this letter, secure beamforming in a multiple intelligent reflecting surfaces (IRSs)-aided millimeter-wave (mmWave) system is investigated. In this system, the secrecy rate is maximized by controlling the on-off status of each IRS as well as optimizing the phase shift matrix of the IRSs. This problem is posed as a joint optimization problem of transmit beamforming and IRS control, whose goal is to maximize the secrecy rate under the total transmission power and unit-modulus constraints. The problem is difficult to solve optimally due to the nonconvexity of constraint conditions and coupled …
We consider an integrated access and backhaul (IAB) node operating in full-duplex (FD) mode. We analyze simultaneous transmission from the New Radio gNB to the IAB node on the backhaul uplink, IAB node to a user equipment (UE) on the access downlink, and IAB transmitter to the IAB receiver on the self-interference (SI) channel. Our contributions include (1) a low complexity algorithm to jointly design the hybrid analog/digital beamformers for all three nodes to maximize the sum spectral efficiency of the access and backhaul links by canceling SI and maximizing received power; (2) derivation of…
This paper considers a lens antenna array-assisted millimeter wave (mmWave) multiuser multiple-input multiple-output (MU-MIMO) system. The base station's beam selection matrix and user terminals' phase-only beamformers are jointly designed with the aim of maximizing the uplink sum rate. In order to deal with the formulated mixed-integer optimization problem, a penalty dual decomposition (PDD)-based iterative algorithm is developed via capitalizing on the weighted minimum mean square error (WMMSE), block coordinate descent (BCD), and minorization-maximization (MM) techniques. Moreover, a low-co…
Millimeter-wave (mmWave) communications provide access to spectra with bandwidths and in abundance. However, the high susceptibility of mmWave to blockage imposes crucial challenges, especially to low-latency services. In this paper, a novel intelligent reflecting surface (IRS) assisted mmWave scheme is proposed to overcome the impact of blockage. New methods are developed to minimize the user power for a multi-user mmWave system by jointly optimizing individual device power, multi-user detection matrix and passive beamforming, subject to delay requirements. An alternating optimization framewo…
In this paper, we investigate the secure beamforming design in an intelligent reflection surface (IRS) assisted millimeter wave (mmWave) system, where the hybrid beamforming (HB) and the passive beamforming (PB) are employed by the transmitter and the IRS, respectively. To maximize the secrecy capacity, the joint optimization of HB and PB is formulated as a nonconvex problem with constant-modulus constraints. To efficiently solve such a challenging problem, the original problem is decomposed into a PB subproblem and an HB subproblem, then these two subproblems are sequentially solved by propos…
Switch-based hybrid network is a promising implementation for beamforming in large-scale millimetre wave (mmWave) antenna arrays. By fully exploiting the sparse nature of the mmWave channel, such hybrid beamforming reduces complexity and power consumption when compared with a structure based on phase shifters. However, the difficulty of designing an optimum beamformer in the analog domain is prohibitive due to the binary nature of such a switch-based structure. Thus, here we propose a new method for designing a switch-based hybrid beamformer for massive MIMO communications in mmWave bands. We …
Recently, full duplex (FD) has been studied in 5G LTE millimeter wave (mmWave) cellular communications for New Radio in 3GPP releases 15-17. FD allows bidirectional transmission over the same resources and has the potential to reduce latency and double spectral efficiency. Self-interference (SI) is the primary drawback. SI can be several orders of magnitude greater than the received signal power, saturate the analog-to-digital converters (ADCs) and degrade communication performance severely. Massive mmWave antenna arrays may provide enough degrees of freedom for spatial multiplexing and SI sup…
We design a lightweight beam-searching algorithm for mobile millimeter-wave systems. We construct and maintain a set of path skeletons, i.e., potential paths between a user and the serving base station to substantially expedite the beam-searching process. To exploit the spatial correlations of the channels, we propose an efficient algorithm that measures the similarity of the skeletons and re-executes the beam-searching procedure only when the old one becomes obsolete. We identify and optimize several tradeoffs between: i) the beam-searching overhead and the instantaneous rate of the users, an…
The use of millimeter wave (mmWave) spectrum for commercial wireless communications is expected to offer data rates in the order of Gigabits-per-second, thus able to support future applications such as Vehicle-to-Vehicle or Vehicle-to-Infrastructure communication. However, especially in urban settings, mmWave signal propagation is sensitive to blockage by surrounding objects, resulting in significant signal attenuation. One approach to mitigate the effect of attenuation is through multi-hop communication with the help of relays. Leveraging the unique characteristics of the mmWave medium, we co…
This paper presents a spatial-temporal single harmonic switching (STHS) transmitter array architecture with enhanced efficiency in the power back-off (PBO) region. STHS is an electromagnetic and circuit co-designed and jointly optimized transmitter array that realizes beamforming and back-off power generation at the same time. The temporal dimension is originally added in STHS to achieve back-off efficiency enhancement, which can be combined with conventional power back-off enhancement methods such as Doherty amplifiers and envelope tracking. The design is validated through a simulation of a t…
In this paper, we propose a new downlink beamforming strategy for mmWave communications using uplink sub-6GHz channel information and a very few mmWave pilots. Specifically, we design a novel dual-input neural network, called FusionNet, to extract and exploit the features from sub-6GHz channel and a few mmWave pilots to accurately predict mmWave beam. To further improve the beamforming performance and avoid over-fitting, we develop two data pre-processing approaches utilizing channel sparsity and data augmentation. The simulation results demonstrate superior performance and robustness of the p…
The concept of reconfigurable intelligent surface (RIS) has been proposed to change the propagation of electromagnetic waves, e.g., reflection, diffraction, and refraction. To accomplish this goal, the phase values of the discrete RIS units need to be optimized. In this paper, we consider RIS-aided millimeter-wave (mmWave) multiple-input multiple-output (MIMO) systems for both accurate positioning and high data-rate transmission. We propose an adaptive phase shifter design based on hierarchical codebooks and feedback from the mobile station (MS). The benefit of the scheme lies in that the RIS …
This paper develops energy-efficient hybrid beamforming designs for mmWave multi-user systems where analog precoding is realized by switches and phase shifters such that radio frequency (RF) chain to transmit antenna connections can be switched off for energy saving. By explicitly considering the effect of each connection on the required power for baseband and RF signal processing, we describe the total power consumption in a sparsity form of the analog precoding matrix. However, these sparsity terms and sparsity-modulus constraints of the analog precoding make the system energy-efficiency max…
In this paper, we investigate an intelligent reflect surface (IRS) assisted multi-user millimeter wave (mmWave) downlink communication system, exploiting IRS to alleviate the blockage effect and enhance the performance of the mmWave system. Considering the impact of IRS on user association, we formulate a sum rate maximization problem by jointly optimizing the passive beamforming at IRS and user association, which is an intractable non-convex problem. Then an alternating optimization algorithm is proposed to solve the problem efficiently. In the proposed algorithm, passive beamforming at IRS i…
Linear hybrid beamformer designs are conceived for the decentralized estimation of a vector parameter in a millimeter wave (mmWave) multiple-input multiple-output (MIMO) Internet of Things network (IoTNe). The proposed designs incorporate both total IoTNe and individual IoTNo power constraints, while also eliminating the need for a baseband receiver combiner at the fusion center (FC). To circumvent the non-convexity of the hybrid beamformer design problem, the proposed approach initially determines the minimum mean square error (MMSE) digital transmit precoder (TPC) weights followed by a simul…
Future millimeter-wave (mmWave) systems, 5G cellular or WiFi, must rely on highly directional links to overcome severe pathloss in these frequency bands. Establishing such links requires the mutual discovery of the transmitter and the receiver %in the angular domain potentially leading to a large latency and high energy consumption. In this work, we show that both the discovery latency and energy consumption can be significantly reduced by using fully digital front-ends. In fact, we establish that by reducing the resolution of the fully-digital front-ends we can achieve lower energy consumptio…
Full-duplex (FD) systems have the capability to transmit and receive at the same time in the same frequency band. FD systems can reduce congestion and latency and improve coverage and spectral efficiency. As a relay, they can increase range and decrease outages. Full-duplex (FD) wireless systems have been emerging as a practical solution to provide high bandwidth, low latency, and big data processing in millimeter wave and Terahertz systems to support cellular networks, autonomous driving, platooning, advanced driving assistance and other systems. However, FD systems suffer from loopback self-…
Unmanned aerial vehicles (UAVs) are the emerging vital components of millimeter wave (mmWave) wireless systems. Accurate beam alignment is essential for efficient beam-based mmWave communications of UAVs with base stations (BSs). Conventional beam sweeping approaches often have large overhead due to the high mobility and autonomous operation of UAVs. Learning-based approaches greatly reduce the overhead by leveraging UAV data, like position to identify optimal beam directions. In this paper, we propose a reinforcement learning (RL)-based framework for UAV-BS beam alignment using deep Q-Network…
In this paper, an reconfigurable intelligent surface (RIS)-aided millimeter wave (mmWave) non-orthogonal multiple access (NOMA) system is considered. In particular, we consider an RIS-aided mmWave-NOMA downlink system with a hybrid beamforming structure. To maximize the achievable sum-rate under a minimum rate constraint for the users and a minimum transmit power constraint, a joint RIS phase shifts, hybrid beamforming, and power allocation problem is formulated. To solve this non-convex optimization problem, we develop an alternating optimization algorithm. Specifically, first, the non-convex…
Perfect alignment in chosen beam sectors at both transmit- and receive-nodes is required for beamforming in mmWave bands. Current 802.11ad WiFi and emerging 5G cellular standards spend up to several milliseconds exploring different sector combinations to identify the beam pair with the highest SNR. In this paper, we propose a machine learning (ML) approach with two sequential convolutional neural networks (CNN) that uses out-of-band information, in the form of camera images, to (i) rapidly identify the locations of the transmitter and receiver nodes, and then (ii) return the optimal beam pair.…
Given the high degree of computational complexity of the channel estimation technique based on the conventional one-dimensional (1-D) compressive sensing (CS) framework employed in the hybrid beamforming architecture, this study proposes two low-complexity channel estimation strategies. One is two-stage CS, which exploits row-group sparsity to estimate angle-of-arrival (AoA) first and uses the conventional 1-D CS method to obtain angle-of-departure (AoD). The other is two-dimensional (2-D) CS, which utilizes a 2-D dictionary to reconstruct the 2-D sparse signal. To conduct a meaningful compari…
In this work, we present a framework analysis of full-duplex (FD) systems for Millimeter Wave (mmWave) analog architecture. Given that FD systems can double the ergodic capacity, such systems experience large losses caused by the loopback self-interference (SI). In addition, systems with analog architecture also suffer from other forms of losses mainly incurred by the constant amplitude (CA) constraint. For this purpose, we propose the projected Gradient Ascent algorithm to maximize the sum rate under the unit-norm and CA constraints. Unlike previous works, our approach achieves the best spect…
In millimeter-wave (mmWave) dual-function radar-communication (DFRC) systems, hybrid beamforming (HBF) is recognized as a promising technique utilizing a limited number of radio frequency chains. In this work, in the presence of extended target and clutters, a HBF design based on the subarray connection architecture is proposed for a multiple-input multiple-output (MIMO) DFRC system. In this HBF, the double-phase-shifter (DPS) structure is embedded to further increase the design flexibility. We derive the communication spectral efficiency (SE) and radar signal-to-interference-plus-noise-ratio …
Hybrid precoders and combiners are designed for cooperative cell-free multi-user millimeter wave (mmWave) multiple-input multiple-output (MIMO) cellular networks for low complexity interference mitigation. Initially, we derive an optimal hybrid transmit beamformer (HTBF) for a broadcast scenario considering both total and per access point (AP) power constraints. Next, an optimal successive hybrid beamformer technique is proposed for unicast and multicast scenarios which relies on the optimal minimum variance distortionless response (MVDR). We demonstrate that it mitigates both the interuser an…
5G millimeter wave (mmWave) technology is envisioned to be an integral part of next-generation vehicle-to-everything (V2X) networks and autonomous vehicles due to its broad bandwidth, wide field of view sensing, and precise localization capabilities. The reliability of mmWave links may be compromised due to difficulties in beam alignment for mobile channels and due to blocking effects between a mmWave transmitter and a receiver. In this paper, we study the channel characteristics for mmWave and sub-6 GHz V2X communications using ray-tracing simulations. We present results for time-varying path…
