arXivDaily arXiv每日学术速递 周一至周五更新
arXiv周末暂无论文更新,休息一下吧,周末愉快~~
arXiv 2005.07823cs.ROstat.AP
收藏

自由曲面尺寸自动检测的最优路径规划

Optimal Path Planning for Automated Dimensional Inspection of Free-Form Surfaces

School of Mechanical Engineering, University of Shanghai for Science and Technology(上海理工大学机械工程学院);Virginia Polytechnic Institute and State University(弗吉尼亚理工学院暨州立大学)

Yinhua Liu, Wenzheng Zhao, Rui Sun, Xiaowei Yue

摘要:

车身结构尺寸检测是车身大批量生产过程监控、质量控制和故障诊断的重要手段。与非接触式测量相比,采用触发式测头的高精度五轴测量机是数据汇集的首选。它可以帮助制造商快速进行准确的检测。随着车身设计中自由曲面的增多和曲面方向的多样化,现有的检测方法无法有效地捕捉车身曲率中的一些新的关键特征。因此,我们需要开发新的路径规划方法的自由曲面的自动尺寸检测。本文提出了一个最佳路径规划系统的自动编程测量点检测,结合探头旋转和有效的碰撞检测。具体而言,方法的贡献包括:(i)一个动态的搜索体积为基础的算法,以检测潜在的碰撞在测量点之间的局部路径;(ii)一个局部路径生成方法,提出了集成的探针轨迹和触针旋转。然后,检测时间矩阵提出了量化的不同的局部路径的测量时间;(iii)的全局检测路径的优化方法,为所有的车身上的关键点,以最小化总的检测时间。最后以某汽车车身为例,验证了该方法的有效性。结果表明,该方法可以离线编程自动生成自由曲面车身的无碰撞路径,在车身检测过程中,虚拟点减少约40%,运动时间减少约32%。

英文摘要:

Structural dimensional inspection is vital for the process monitoring, quality control, and fault diagnosis in the mass production of auto bodies. Comparing with the non-contact measurement, the high-precision five-axis measuring machine with the touch-trigger probe is a preferred choice for data collection. It can assist manufacturers in making accurate inspection quickly. As the increase of free-form surfaces and diverse surface orientations in auto body design, existing inspection approaches cannot capture some new critical features in the curvature of auto bodies in an efficient way. Therefore, we need to develop new path planning methods for automated dimensional inspection of free-form surfaces. This paper proposes an optimal path planning system for automated programming of measuring point inspection by incorporating probe rotations and effective collision detection. Specifically, the methodological contributions include: (i) a dynamic searching volume-based algorithm is developed to detect potential collisions in the local path between measurement points; (ii) a local path generation method is proposed with the integration of the probe trajectory and the stylus rotation. Then, the inspection time matrix is proposed to quantify the measuring time of diverse local paths; (iii) an optimization approach of the global inspection path for all critical points on the auto body is developed to minimize the total inspection time. A case study has been conducted on an auto body to verify the performance of the proposed method. Results show that the collision-free path for the free-form auto body could be generated automatically with off-line programming, and the proposed method produces about 40% fewer dummy points and needs 32% less movement time in the auto body inspection process.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑