Wirelessly-powered sensor networks (WPSNs) are becoming increasingly important in different monitoring applications. We consider a WPSN where a multiple-antenna base station, which is dedicated for energy transmission, sends pilot signals to estimate the channel state information and consequently shapes the energy beams toward the sensor nodes. Given a fixed energy budget at the base station, in this paper, we investigate the novel problem of optimally allocating the power for the channel estimation and for the energy transmission. We formulate this non-convex optimization problem for general channel estimation and beamforming schemes that satisfy some qualification conditions. We provide a new solution approach and a performance analysis in terms of optimality and complexity. We also present a closed-form solution for the case where the channels are estimated based on a least square channel estimation and a maximum ratio transmit beamforming scheme. The analysis and simulations indicate a significant gain in terms of the network sensing rate, compared to the fixed power allocation, and the importance of improving the channel estimation efficiency.
This paper shows that wirelessly powered backscatter communications is subject to a fundamental tradeoff between the harvested energy at the tag and the reliability of the backscatter communication, measured in terms of SNR at the reader. Assuming the RF transmit signal is a multisine waveform adaptive to the channel state information, we derive a systematic approach to optimize the transmit waveform weights (amplitudes and phases) in order to enlarge as much as possible the SNRenergy region. Performance evaluations confirm the significant benefits of using multiple frequency components in the…
In this article, we put forward the mobile crowd sensing paradigm based on ubiquitous wearable devices carried by human users. The key challenge for mass user involvement into prospective urban crowd sending applications, such as monitoring of large-scale phenomena (e.g., traffic congestion and air pollution levels), is the appropriate sources of motivation. We thus advocate for the use of wireless power transfer provided in exchange for sensed data to incentivize the owners of wearables to participate in collaborative data collection. Based on this construction, we develop the novel concept o…
In this work, we consider an energy harvesting device (EHD) served by an access point with a single antenna that is used for both wireless power transfer (WPT) and data transfer. The objective is to maximize the expected throughput of the EHD over a finite horizon when the channel state information is only available causally. The EHD is energized by WPT for a certain duration, which is subject to optimization, and then, EHD transmits its information bits to the AP until the end of the time horizon by employing optimal dynamic power allocation. The joint optimization problem is modeled as a dyn…
Federated edge learning (FEEL) is a widely adopted framework for training an artificial intelligence (AI) model distributively at edge devices to leverage their data while preserving their data privacy. The execution of a power-hungry learning task at energy-constrained devices is a key challenge confronting the implementation of FEEL. To tackle the challenge, we propose the solution of powering devices using wireless power transfer (WPT). To derive guidelines on deploying the resultant wirelessly powered FEEL (WP-FEEL) system, this work aims at the derivation of the tradeoff between the model…
This letter deals with the opportunistic beamforming (OBF) scheme for multi-antenna downlink with spatial randomness. In contrast to conventional OBF, the terminals return only 1-bit feedback, which is powered by wireless power transfer through a rectenna array. We study two fundamental topologies for the combination of the rectenna elements; the direct-current combiner and the radio-frequency combiner. The beam outage probability is derived in closed form for both combination schemes, by using high order statistics and stochastic geometry.
Wirelessly powered backscatter communication (WPBC) has been identified as a promising technology for low-power communication systems, which can reap the benefits of energy beamforming to improve energy transfer efficiency. Existing studies on energy beamforming fail to simultaneously take energy supply and information transfer in WPBC into account. This paper takes the first step to fill this gap, by considering the trade-off between the energy harvesting rate and achievable rate using estimated backscatter channel state information (BS-CSI). To ensure reliable communication and user fairness…
In this paper, we focus on a wireless-powered sensor network coordinated by a multi-antenna access point (AP). Each node can generate sensing information and report the latest information to the AP using the energy harvested from the AP's signal beamforming. We aim to minimize the average age-of-information (AoI) by adapting the nodes' transmission scheduling and the transmission control strategies jointly. To reduce the transmission delay, an intelligent reflecting surface (IRS) is used to enhance the channel conditions by controlling the AP's beamforming vector and the IRS's phase shifting m…
This paper presents the design, implementation and evaluation of In-N-Out, a software-hardware solution for far-field wireless power transfer. In-N-Out can continuously charge a medical implant residing in deep tissues at near-optimal beamforming power, even when the implant moves around inside the human body. To accomplish this, we exploit the unique energy ball pattern of distributed antenna array and devise a backscatter-assisted beamforming algorithm that can concentrate RF energy on a tiny spot surrounding the medical implant. Meanwhile, the power levels on other body parts stay in low le…
We integrate a wireless powered communication network with a cooperative cognitive radio network, where multiple secondary users (SUs) powered wirelessly by a hybrid access point (HAP) help a primary user relay the data. As a reward for the cooperation, the secondary network gains the spectrum access where SUs transmit to HAP using time division multiple access. To maximize the sum-throughput of SUs, we present a secondary sum-throughput optimal resource allocation (STORA) scheme. Under the constraint of meeting target primary rate, the STORA scheme chooses the optimal set of relaying SUs and …
With the explosive growth of smart IoT devices at the edge of the Internet, embedding sensors on mobile devices for massive data collection and collective environment sensing has been envisioned as a cost-effective solution for IoT applications. However, existing IoT platforms and framework rely on dedicated middleware for (semi-) centralized task dispatching, data storage and incentive provision. Consequently, they are usually expensive to deploy, have limited adaptability to diverse requirements, and face a series of data security and privacy issues. In this paper, we employ permissionless b…
Movable Antennas Enabled Wireless Powered Networks: Principles and Technologies
School of Information and Communication Engineering, Xi’an Jiaotong University（西安交通大学信息与通信工程学院）；School of Cyber Science and Engineering, Xi’an Jiaotong University（西安交通大学网络空间安全学院）；Department of Electronic Engineering, Shanghai Jiao Tong University（上海交通大学电子工程系）；State Key Laboratory of Networking and Switching Technology, Beijing University of Posts and Telecommunications（北京邮电大学固定网络与交换技术国家重点实验室）
Intelligent reflecting surface (IRS) is a promising technology to improve the performance of wireless powered communication networks (WPCNs) due to its capability to reconfigure signal propagation environments via smart reflection. In particular, the high passive beamforming gain promised by IRS can significantly enhance the efficiency of both downlink wireless power transfer (DL WPT) and uplink wireless information transmission (UL WIT) in WPCNs. Although adopting different IRS phase shifts for DL WPT and UL WIT, i.e., dynamic IRS beamforming, is in principle possible but incurs additional si…
Devices can now be powered wirelessly by Access Points (APs). However, an AP cannot transmit frequently to charge devices as it may starve other nearby APs operating on the same channel. Consequently, there is a need to schedule the transmissions of APs to ensure their data queues remain short whilst charging energy-harvesting devices. We present a finite-horizon Markov Decision Process (MDP) to capture the queue states at APs and also channel conditions to nodes. We then use the MDP to investigate the following transmission policies: max weight, max queue, best channel state and random. Our r…
Intelligent reflecting surface (IRS) is an emerging technology to enhance the energy- and spectrum-efficiency of wireless powered communication networks (WPCNs). In this paper, we investigate an IRS-assisted multiuser multiple-input single-output (MISO) WPCN, where the single-antenna wireless devices (WDs) harvest wireless energy in the downlink (DL) and transmit their information simultaneously in the uplink (UL) to a common hybrid access point (HAP) equipped with multiple antennas. Our goal is to maximize the weighted sum rate (WSR) of all the energy-harvesting users. To make full use of the…
We present the first power over Wi-Fi system that delivers power and works with existing Wi-Fi chipsets. Specifically, we show that a ubiquitous piece of wireless communication infrastructure, the Wi-Fi router, can provide far field wireless power without compromising the network's communication performance. Building on our design we prototype, for the first time, battery-free temperature and camera sensors that are powered using Wi-Fi chipsets with ranges of 20 and 17 feet respectively. We also demonstrate the ability to wirelessly recharge nickel-metal hydride and lithium-ion coin-cell batte…
In this paper, we investigate joint beamforming for energy-throughput tradeoff in a sustainable cloud radio access network system, where multiple base stations (BSs) powered by independent renewable energy sources will collaboratively transmit wireless information and energy to the data receiver and the energy receiver simultaneously. In order to obtain the optimal joint beamforming design over a finite time horizon, we formulate an optimization problem to maximize the throughput of the data receiver while guaranteeing sufficient RF charged energy of the energy receiver. Although such problem …
This paper studies a new concept so-called green cell-less radio frequency (RF) wireless power transfer (WPT) networks. We consider a scenario in which multiple indoor access points (APs) equipped with outdoor energy harvesters are connected with a central control unit via backhaul links. Further, such APs exploit the harnessed green energy to recharge wirelessly indoor devices under the coordination of the control unit. Considering the network, we focus on AP selection and beamforming optimization to maximize the total energy harvesting (EH) rate. The resulting mathematical problem has the fo…
Emerged as a promising solution for future wireless communication systems, intelligent reflecting surface (IRS) is capable of reconfiguring the wireless propagation environment by adjusting the phase-shift of a large number of reflecting elements. To quantify the gain achieved by IRSs in the radio frequency (RF) powered Internet of Things (IoT) networks, in this work, we consider an IRS-assisted cellular-based RFpowered IoT network, where the cellular base stations (BSs) broadcast energy signal to IoT devices for energy harvesting (EH) in the charging stage, which is utilized to support the up…
In this paper, we consider a wireless powered communication network (WPCN) consisting of a multi-antenna hybrid access point (HAP) that transfers wireless energy to and receives sensing data from a cluster of low-power wireless devices (WDs). To enhance the throughput performance of some far-away WDs, we allow one of the WDs to act as the cluster head (CH) that helps forward the messages of the other cluster members (CMs). However, the performance of the proposed cluster-based cooperation is fundamentally limited by the high energy consumption of the CH, who needs to transmit all the WDs' mess…
Wireless energy transfer is an emerging technology that is used in networks of battery-powered devices in order to deliver energy and keep the network functional. Existing state-of-the-art studies have mainly focused on applying this technology on networks of relatively strong computational and communicational capabilities (wireless sensor networks, ad-hoc networks); also they assume energy transfer from special chargers to regular network nodes. Different from these works, we study how to efficiently transfer energy wirelessly in populations of battery-limited devices, towards prolonging thei…
In the future, sensor nodes or Internet of Things (IoTs) will be tasked with sampling the environment. These nodes/devices are likely to be powered by a Hybrid Access Point (HAP) wirelessly, and may be programmed by the HAP with a {\em sampling time} to collect sensory data, carry out computation, and transmit sensed data to the HAP. A key challenge, however, is random channel gains, which cause sensor nodes to receive varying amounts of Radio Frequency (RF) energy. To this end, we formulate a stochastic program to determine the charging time of the HAP and sampling time of sensor nodes. Our o…
In this paper we analyze the trade-offs between energy and throughput for links in a wireless sensor network. Our application of interest is one in which a number of low-powered sensors need to wirelessly communicate their measurements to a communications sink, or destination node, for communication to a central processor. We focus on one particular sensor source, and consider the case where the distance to the destination is beyond the peak power of the source. A relay node is required. Transmission energy of the sensor and the relay can be adjusted to minimize the total energy for a given th…
