XFEL的压电控制
Piezo control for XFEL
摘要:
工作在高Q值的超导腔需要精确地调谐到射频频率。良好调谐的腔确保良好的场稳定性,并且需要最小水平的RF功率来达到操作梯度水平。XFEL加速器的TESLA腔使用由控制系统驱动的慢(步进电机)和快(压电)调谐器进行调谐。该控制系统的目标是即使在存在干扰效应(LFD -洛伦兹力失谐和颤噪效应)的情况下也尽可能地保持腔的失谐接近零。步进电机调谐器用于粗调腔,而压电致动器用于微调和扰动补偿。压电控制系统的关键部分是压电驱动器。为了补偿LFD,需要具有相对高的电压(高达100 V)和高电流(高达1A)的压电驱动。由于压电元件容易受到过电压、过电流和过温的破坏,因此必须特别注意保持压电元件的健康。使事情变得更糟和更关键的是,在模块组装之后,压电交换是不可能的。因此,特殊硬件必须辅助功率放大器,检测危险条件并在需要时禁用压电操作。它必须是自动防故障的,所以即使在故障的情况下,压电元件也会存活下来。它还必须坚固耐用,并且不得干扰或禁用正常操作。由于有许多通道(主/从RF通道为16个),硬件解决方案必须具有良好的可扩展性。本文讨论了XFEL压电驱动器的设计,以及PEM(Power and Energy Monitor)对驱动器运行的监控和对压电元件的保护。所取得的成果和整个系统的操作进行了演示。
英文摘要:
The superconducting cavities operated at high Q level need to be precisely tuned to the RF frequency. Well tuned cavities assure the good field stability and require a minimum level of RF power to reach the operating gradient level. The TESLA cavities at XFEL accelerator are tuned using slow (step motors) and fast (piezo) tuners driven by the control system. The goal of this control system is to keep the detuning of the cavity as close to zero as possible even in the presence of disturbing effects (LFD - Lorentz Force Detuning and microphonics). The step motor tuners are used to coarse cavity tuning while piezo actuators are used to fine-tuning and disturbance compensation. The crucial part of the piezo control system is the piezo driver. To compensate LFD the piezo driving with relatively high voltage (up to 100V) and high current (up to 1A) is needed. Since the piezo components are susceptible to destruction with overvoltage, overcurrent, and also overtemperature, one has to pay special attention to keep the piezos healthy. What makes things worse and more critical, is that the piezo exchange is not possible after the module is assembled. Therefore the special hardware must be assisting the power amplifier, detecting the dangerous conditions and disabling piezo operation when needed. It must be fail-safe, so even in a case of failure the piezos shall survive. It must be also robust and it must not disturb or disable normal operation. Due to many channels (16 for master/slave RF), the hardware solution must be well scalable. The paper discuss the design of XFEL's piezo driver together with PEM (Power and Energy Monitor) supervising the driver operation and preventing piezos from destruction. The achieved results and operation of the complete system are demonstrated.
机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。