The main promise of tunnel FETs (TFETs) is to enable supply voltage ($V_{DD}$) scaling in conjunction with dimension scaling of transistors to reduce power consumption. However, reducing $V_{DD}$ and channel length ($L_{ch}$) typically deteriorates the ON- and OFF-state performance of TFETs, respectively. Accordingly, there is not yet any report of a high perfor]mance TFET with both low V$_{DD}$ ($\sim$0.2V) and small $L_{ch}$ ($\sim$6nm). In this work, it is shown that scaling TFETs in general requires scaling down the bandgap $E_g$ and scaling up the effective mass $m^*$ for high performance. Quantitatively, a channel material with an optimized bandgap ($E_g\sim1.2qV_{DD} [eV]$) and an engineered effective mass ($m*^{-1}\sim40 V_{DD}^{2.5} [m_0^{-1}]$) makes both $V_{DD}$ and $L_{ch}$ scaling feasible with the scaling rule of $L_{ch}/V_{DD}=30~nm/V$ for $L_{ch}$ from 15nm to 6nm and corresponding $V_{DD}$ from 0.5V to 0.2V.
A current due to a tunneling event that involves three times the charge of an electron was observed in the current - voltage characteristics of a superconducting single-electron tunneling transistor. In this tunnel event, a Cooper pair tunnels through one tunnel barrier simultaneously with a quasiparticle that tunnels through a second tunnel barrier which is about 0.5 microns distant from the first tunnel barrier. This current was observed in a bias regime where current flow due to sequential quasiparticle tunneling is forbidden due to the Coulomb blockade.
Using self-consistent quantum transport simulation on realistic devices, we show that InAs band-to-band Tunneling Field Effect Transistors (TFET) with a heavily doped pocket in the gate-source overlap region can offer larger ON current and steeper subthreshold swing as compared to conventional tunneling transistors. This is due to an additional tunneling contribution to current stemming from band overlap along the body thickness. However, a critical thickness is necessary to obtain this advantage derived from 'vertical' tunneling. In addition, in ultra small InAs TFET devices, the subthreshold…
We theoretically study the tunnelling current of a single electron transistor (SET) under optical pumping. It found that holes in the quantum dot(QD) created by optical pumping lead to new channels for the electrons tunnelling from emitter to collector. As a consequence, an electron can tunnel through the QD via additional channels, characterized by the exciton, trion and biexciton states. The binding energy of exciton complexes can be determined by the Coulomb oscillatory tunnelling current.
We propose a concept for a graphene tunnel field-effect transistor. The main idea is based on the use of two graphene electrodes with zigzag termination divided by a narrow gap under the influence of the common gate. Our analysis shows that such device will have a pronounced switching effect at low gate voltage and high on/off current ratio at room temperature.
We measure electron tunneling in single-molecule transistors made from C_{140}, a molecule with a mass-spring-mass geometry chosen as a model system to study electron-vibration coupling. We observe vibration-assisted tunneling at an energy corresponding to the stretching mode of C_{140}. Molecular modeling provides explanations for why this mode couples more strongly to electron tunneling than the other internal modes of the molecule. We make comparisons between the observed tunneling rates and those expected from the Franck-Condon model.
Tunnel Field Effect Transistors (TFET) have extremely low leakage current, exhibit excellent subthreshold swing and are less susceptible to short channel effects. However, TFETs do face certain special challenges, particularly with respect to the process induced variations in (i) the channel length and (ii) the thickness of the silicon thin-film and the gate oxide. This paper, for the first time, studies the impact of the above process variations on the electrical characteristics of a Double Gate Tunnel Field Effect Transistor (DGTFET). Using two dimensional device simulations, we propose the …
The dielectric engineered tunnel field-effect transistor (DE-TFET) as a high performance steep transistor is proposed. In this device, a combination of high-k and low-k dielectrics results in a high electric field at the tunnel junction. As a result a record ON-current of about 1000 uA/um and a subthreshold swing (SS) below 20mV/dec are predicted for WTe2 DE-TFET. The proposed TFET works based on a homojunction channel and electrically doped contacts both of which are immune to interface states, dopant fluctuations, and dopant states in the band gap which typically deteriorate the OFF-state pe…
We have studied quantum transport in Graphene Nanoribbon Tunnel Field-Effect Transistors. Unlike other studies on similar structures, we have included dissipative processes induced by inelastic electron-phonon scattering and edge roughness in the nanoribbon self-consistently within a non-equilibrium transport simulation. Our results show that the dissipative scattering imposes a limit to the minimum OFF current and a minimum subthreshold swing that can be obtained even for long channel lengths where direct source-drain tunneling is inhibited. The edge roughness, in presence of dissipative scat…
We demonstrate a tunnel field effect transistor based on a lateral heterostructure patterned from an $\mathrm{LaAlO_3/SrTiO_3}$ electron gas. Charge is injected by tunneling from the $\mathrm{LaAlO_3}$/$\mathrm{SrTiO_3}$ contacts and the current through a narrow channel of insulating $\mathrm{SrTiO_3}$ is controlled via an electrostatic side gate. Drain-source I/V-curves have been measured at low and elevated temperatures. The transistor shows strong electric-field and temperature-dependent behaviour with a steep sub-threshold slope %of up to as small as $10\:\mathrm{mV/decade}$ and a transcon…
Vertical tunneling field-effect-transistor (FET) based on graphene heterojunctions with layers of hBN is simulated by self-consistent quantum transport simulations. It is found that the asymmetric p-type and n-type conduction is due to work function deference between the graphene contact and the tunneling channel material. Modulation of the bottom-graphene-contact plays an important role in determining the switching characteristic of the device. Due to the electrostatic short-channel-effects stemming from the vertical-FET structure, the output I-V characteristics do not saturate. The scaling b…
The high efficiency of a tunnel magnetic transistor as a source of spin-polarized electrons has been proven recently [X. Jiang {\it et al.}, Phys. Rev. Lett. {\bf 90}, 256603 (2003)]. A concept of this device based on an active group of hot electrons controlling the collector current and experiencing predominantly inelastic scattering in the base is developed. It takes into account the interconnection between the injection and filtering of spin-polarized electrons in different elements of the device. Explicit expressions for the parameters of the device in terms of the basic parameters of the …
In this paper we have developed a two dimensional (2D) analytical model for surface potential and drain current for a long channel Dual Material Gate (DMG) Silicon-on-Insulator (SOI) Tunneling Field Effect Transistor (TFET). This model includes the effect of drain voltage, gate metal work function, oxide thickness and silicon film thickness, without assuming a fully depleted channel. The proposed model also includes the effect of charge accumulation at the interface of the two gates and the variation in the tunneling volume with the applied gate voltage. The accuracy of the model is tested usi…
We propose a Heterojunction Vertical Tunneling FET and show using self-consistent ballistic quantum transport simulations that it can provide very steep subthreshold swings and high ON current, thereby improving the scalability of Tunnel FETs for high performance. The turn-on in pocket region of the device is dictated by modulation of heterojunction barrier height. The steepness of turn-on is increased because of simultaneous onset of tunneling in the pocket and the region underneath and also due to contribution to current by vertical tunneling in the pocket. These factors can be engineered by…
In this paper, we propose the application of a Dual Material Gate (DMG) in a Tunnel Field Effect Transistor (TFET) to simultaneously optimize the on-current, the off-current and the threshold voltage, and also improve the average subthreshold slope, the nature of the output characteristics and the immunity against the DIBL effects. We demonstrate that if appropriate work-functions are chosen for the gate materials on the source side and the drain side, the tunnel field effect transistor shows a significantly improved performance. We apply the technique of DMG in a Strained Double Gate Tunnel F…
The rectification of electromagnetic waves to direct currents is a crucial process for energy harvesting, beyond-5G wireless communications, ultra-fast science, and observational astronomy. As the radiation frequency is raised to the sub-terahertz (THz) domain, ac-to-dc conversion by conventional electronics becomes challenging and requires alternative rectification protocols. Here we address this challenge by tunnel field-effect transistors made of bilayer graphene (BLG). Taking advantage of BLG's electrically tunable band structure, we create a lateral tunnel junction and couple it to an ant…
Tunneling field-effect transistors (TFETs) based on 2D materials are promising steep sub-threshold swing (SS) devices due to their tight gate control. There are two major methods to create the tunnel junction in these 2D TFETs: electrical and chemical doping. In this work, design guidelines for both electrically and chemically doped 2D TFETs are provided using full band atomistic quantum transport simulations in conjunction with analytic modeling. Moreover, several 2D TFETs' performance boosters such as strain, source doping, and equivalent oxide thickness (EOT) are studied. Later on, these pe…
The quantum conductance of the single-electron tunneling (SET) transistor is investigated in this paper by the functional integral approach. The formalism is valid for arbitrary tunnel resistance of the junctions forming the SET transistor at any temperature. The path integrals are evaluated by the semiclassical method to yield an explicit non-perturbation form of the quantum conductance of the SET transistor. An anomaly of the quantum conductance is found if the tunnel resistances are much smaller than the quantum resistance. The dependence of the conductance on the gate voltage is also discu…
Tunnel field effect transistor (TFET) devices are attractive as they show good scalability and have very low leakage current. However they suffer from low on-current and high threshold voltage. In order to employ the TFET for circuit applications, these problems need to be tackled. In this paper, a novel lateral strained double-gate TFET (SDGTFET) is presented. Using device simulation, we show that the SDGTFET has a higher on-current, low leakage, low threshold voltage, excellent subthreshold slope, and good short channel effects and also meets important ITRS guidelines.
We report on a new type of single-electron transistor (SET) comprising two highly resistive Cr thin-film strips (~ 1um long) connecting a 1 um-long Al island to two Al outer electrodes. These resistors replace small-area oxide tunnel junctions of traditional SETs. Our transistor with a total asymptotic resistance of 110 kOhm showed a very sharp Coulomb blockade and reproducible, deep and strictly e-periodic gate modulation in wide ranges of bias currents I and gate voltages V_g. In the Coulomb blockade region (|V| < 0.5 mV), we observed a strong suppression of the cotunneling current allowing …
We provide a detailed study of the interface Trap Assisted Tunneling (TAT) mechanism in tunnel field effect transistors to show how it contributes a major leakage current path before the Band To Band Tunneling (BTBT) is initiated. With a modified Shockley-Read-Hall formalism, we show that at room temperature, the phonon assisted TAT current always dominates and obscures the steep turn ON of the BTBT current for common densities of traps. Our results are applicable to top gate, double gate and gate all around structures where the traps are positioned between the source-channel tunneling region.…
The electrical performance of a tunnel field-effect transistor depends critically on the band offset at their semiconductor heterojunction interface. Historically, it has been difficult to experimentally determine how the electronic bands align at the heterojunction interface. We report here on experimental methods to ascertain a complete energy band alignment of a broken-gap tunnel field-effect transistor based on an InAs/GaSb hetero-junction. By using graphene as an optically transparent electrode in a traditional internal photoemission measurement, both the electron and hole barrier heights…
Field-effect transistors based on band-to-band tunneling (BTBT) have gained a lot of recent interest due to their potential for reducing power dissipation in integrated circuits. In this paper we present a detailed performance comparison between conventional n-i-n MOSFET transistors, and BTBT transistors based on the p-i-n geometry (p-i-n TFET), using semiconducting carbon nanotubes as the model channel material. Quantum transport simulations are performed using the nonequilibrium Green's function formalism including realistic phonon scattering. We find that the TFET can indeed produce subthre…
We investigate a hybrid structure consisting of $20\pm4$ implanted $^{31}$P atoms close to a gate-induced silicon single electron transistor (SiSET). In this configuration, the SiSET is extremely sensitive to the charge state of the nearby centers, turning from the off state to the conducting state when the charge configuration is changed. We present a method to measure fast electron tunnel rates between donors and the SiSET island, using a pulsed voltage scheme and low-bandwidth current detection. The experimental findings are quantitatively discussed using a rate equation model, enabling the…
Thickness engineered tunneling field-effect transistors (TE-TFET) as a high performance ultra-scaled steep transistor is proposed. This device exploits a specific property of 2D materials: layer thickness dependent energy bandgap (Eg). Unlike the conventional hetero-junction TFETs, TE-TFET uses spatially varying layer thickness to form a hetero-junction. This offers advantages by avoiding the interface states and lattice mismatch problems. Furthermore, it boosts the ON-current to 1280$μA/μm$ for 15nm channel length. TE-TFET shows a channel length scalability down to 9nm with constant field sca…
In this work, device performances of tunneling field effect transistors (TFETs) based on phosphorene are explored via self-consistent atomistic quantum transport simulations. Phosphorene is an ultra-thin two-dimensional (2-D) material with a direct band gap suitable for TFETs applications. Our simulation shows that phosphorene TFETs exhibit subthreshold slope (SS) below 60 mV/dec and a wide range of on-current depending on the transport direction due to highly anisotropic band structures of phosphorene. By benchmarking with monolayer MoTe2 TFETs, we predict that phosphorene TFETs oriented in t…
We experimentally characterise the impedance of a single electron transistor (SET) at an excitation frequency comparable to the electron tunnel rate. Differently from usual rf-SET operations, the excitation signal is applied to the gate of the device. At zero source-drain bias the single electron transistor displays both resistive (Sisyphus resistance) and reactive (tunnelling capacitance) components to its impedance. We study the bias dependence of the complex impedance, investigating its response as the electron tunnel rate becomes large with respect to the driving frequency. The experimenta…
A peculiarity of the single-electron transistor effect makes it possible to observe this effect even in structures lacking a gate electrode altogether. The proposed method can be useful for experimental study of charging effects in structures with an extremely small central island confined between tunnel barriers like a nanometer-sized quantum dot or a macromolecule probed with a tunneling microscope), where it is impossible to provide a gate electrode for control of the tunnel current.
Using calibrated simulations, we report a detailed study of the doping-less tunnel field effect transistor (TFET) on a thin intrinsic silicon film using charge plasma concept. Without the need for any doping, the source and drain regions are formed using the charge plasma concept by choosing appropriate work functions for the source and drain metal electrodes. Our results show that the performance of the doping-less TFET is similar to that of a corresponding doped TFET. The doping-less TFET is expected to be free from problems associated with random dopant fluctuations. Further, fabrication of…
In this paper, we have presented the impact of the gate leakage through thin gate dielectrics (SiO2 and high-\k{appa} gate dielectric) on the subthreshold characteristics of the tunnel field effect transistors (TFET) for a low operating voltage of 0.5 V. Using calibrated two-dimensional simulations it is shown that even for such a low operating voltage, the gate leakage substantially degrades several subthreshold parameters of the TFET such as the off-state current, minimum subthreshold swing and average subthreshold swing. While the drain-offset as well as the short-gate are effective methods…
Vertical graphene-based device concepts that rely on quantum mechanical tunneling are intensely being discussed in literature for applications in electronics and optoelectronics. In this work, the carrier transport mechanisms in semiconductor-insulator-graphene (SIG) capacitors are investigated with respect to their suitability as the electron emitter in vertical graphene base transistors (GBTs). Several dielectric materials as tunnel barriers are compared, including dielectric double layers. Using bilayer dielectrics, we experimentally demonstrate significant improvements in the electron inje…
We theoretically study the tunnel magnetoresistance(TMR) of ferromagnet / superconductor / ferromagnet single-electron tunneling transistors with a special attention to the parity effect. It is shown that in the plateau region, there is no spin accumulation in the island even at finite bias voltage. However, the information of the injected spin is carried by the excess electron and thus the TMR exists. The spin relaxation rate of the excess electron can be estimated from the TMR. We also show that the TMR increases with decreasing the size of the superconducting island.
We report about the fabrication and analysis of the properties of Cr/CrO_x/Cr tunnel junctions and SET transistors, prepared by different variants of direct-writing multilayer technique. In all cases, the CrO_x tunnel barriers were formed in air under ambient conditions. From the experiments on single junctions, values for the effective barrier height and thickness were derived. For the Cr/CrO_x/Cr SET transistors we achieved minimal junction areas of 17 x 60 nm^2 using a scanning transmission electron microscope for the e-beam exposure on Si_3N_4 membrane substrate. We discuss the electrical …
In this work, we demonstrate a silicon nanocrystal Field Effect Transistor (ncFET). Its operation is similar to that of a Tunnelling Field Effect Transistor (TFET) with two barriers in series. The tunnelling barriers are fabricated in very thin silicon dioxyde and the channel in intrinsic polycrystalline silicon. The absence of doping eliminates the problem of achieving sharp doping profiles at the junctions, which has proven a challenge for large-scale integration and in principle allows scaling down the atomic level. The demonstrated ncFET features a 10$^4$ on/off current ratio at room tempe…
We study the influence of Coulomb interaction on the thermoelectric transport coefficients for a metallic single-electron transistor. By performing a perturbation expansion up to second order in the tunnel-barrier conductance, we include sequential and cotunneling processes as well as quantum fluctuations that renormalize the charging energy and the tunnel conductance. We find that Coulomb interaction leads to a strong violation of the Wiedemann-Franz law: the Lorenz ratio becomes gate-voltage dependent for sequential tunneling, and is increased by a factor 9/5 in the cotunneling regime. Final…
We theoretically investigate the finite-frequency as well as the zero-frequency charge-current fluctuations through a noncollinear single-electron spin-valve transistor in the limit of sequential tunneling. The system under consideration consists of two tunnel junctions that connect a small central metallic island to two ferromagnetic leads with noncollinear magnetization. Due to the spin-dependent tunnel coupling and the electron-electron interaction on the central electrode an exchange field that acts on the accumulated island spin is present. We analyze how this many-particle interaction ef…
2D transition metal dichalcogenides (TMDs) have attracted a lot of attention recently for energy-efficient tunneling-field-effect transistor (TFET) applications due to their excellent gate control resulting from their atomically thin dimensions. However, most TMDs have bandgaps (Eg) and effective masses (m*) outside the optimum range needed for high performance. It is shown here that the newly discovered 2D material, few-layer phosphorene, has several properties ideally suited for TFET applications: 1) direct Eg in the optimum range ~1.0-0.4 eV, 2) light transport m* (0.15m0), 3) anisotropic m…
In a continuous search for the energy-efficient electronic switches, a great attention is focused on tunnel field-effect transistors (TFETs) demonstrating an abrupt dependence of the source-drain current on the gate voltage. Among all TFETs, those based on one-dimensional (1D) semiconductors exhibit the steepest current switching due to the singular density of states near the band edges, though the current in 1D structures is pretty low. In this paper, we propose a TFET based on 2D graphene bilayer which demonstrates a record steep subthreshold slope enabled by van Hove singularities in the de…
We demonstrate a mechanism for a dual layer, vertical field-effect transistor, in which nearly-depleting one layer will extend its wavefunction to overlap the other layer and increase tunnel current. We characterize this effect in a specially designed GaAs/AlGaAs device, observing a tunnel current increase of two orders of magnitude at cryogenic temperatures, and we suggest extrapolations of the design to other material systems such as graphene.
Black phosphorus (BP) tunneling transistors (TFETs) using heterojunction (He) are investigated by atomistic quantum transport simulations. It is observed that edge states have a great impact on transport characteristics of BP He-TFETs, which result in the potential pinning effect and deteriorate the gate control. While, on-state current can be effectively enhanced by using hydrogen to saturate the edge dangling bonds in BP He-TFETs, in which edge states are quenched. By extending layered BP with a smaller band gap to the channel region and modulating the BP thickness, device performance of BP …
We investigate low-temperature and low-voltage-bias charge transport in a superconducting Al single electron transistor in a dissipating environment, realized as on-chip high-ohmic Cr microstrips. In our samples with relatively large charging energy values Ec > EJ, where EJ is the energy of the Josephson coupling, two transport mechanisms were found to be dominating, both based on discrete tunneling of individual Cooper pairs: Depending on the gate voltage Vg, either sequential tunneling of pairs via the transistor island (in the open state of the transistor around the points Qg = CgVg = e mod…
This work reports the design and analysis of an n-type tunneling field effect transistor based on InN. The tunneling current is evaluated from the fundamental principles of quantum mechanical tunneling and semiclassical carrier transport. We investigate the RF performance of the device. High transconductance of 2 mS/um and current gain cut-off frequency of around 460 GHz makes the device suitable for THz applications. A significant reduction in gate to drain capacitance is observed under relatively higher drain bias. In this regard, the avalanche breakdown phenomenon in highly doped InN juncti…
We report on the fabrication and electrical characterization at millikelvin temperatures of a novel silicon single-electron transistor (Si-SET). The island and source-drain leads of the Si-SET are formed by the implantation of phosphorus ions to a density above the metal-insulator-transition, with the tunnel junctions created by undoped regions. Surface gates above each of the tunnel junctions independently control the tunnel coupling between the Si-SET island and leads. The device shows periodic Coulomb blockade with a charging energy e$^2$/2C$_Σ$ $\sim$ 250 $μ$eV, and demonstrates a reproduc…
Graphene/silicon heterostructures have attracted tremendous interest as a new platform for diverse electronic and photonic devices such as barristors, solar cells, optical modulators, and chemical sensors. The studies to date largely focus on junctions between graphene and lightly-doped silicon, where a Schottky barrier is believed to dominate the carrier transport process. Here we report a systematic investigation of carrier transport across the heterojunctions formed between graphene and highly-doped silicon. By varying the silicon doping level and the measurement temperature, we show that t…
The influence of edge vacancies on the working ability of the planar graphene tunnel field-effect transistor (TFET) is studied at various concentrations and distributions (normal, uniform, periodic) of defects. All calculations are performed by using the Green's function method and the tight-binding approximation. It is shown that the transistor performance depends critically on two important factors associated with the defects: the destruction of the edge-localized electronic states and the emergence of subpeaks near the Fermi level. The supportable operation conditions of the TFET are found …
Tunneling field-effect transistors (TFETs) have gained a great deal of recent interest due to their potential to reduce power dissipation in integrated circuits. One major challenge for TFETs so far has been achieving high drive currents, which is a prerequisite for high-performance operation. In this paper we explore the performance potential of a 1D TFET with a broken-gap heterojunction source injector using dissipative quantum transport simulations based on the nonequilibrium Green's function formalism, and the carbon nanotube bandstructure as the model 1D material system. We provide detail…
By operating the radio frequency single electron transistor (rf-SET) as a mixer we present measurements in which the RC roll-off of the tunnel junctions is observed at high frequencies. Our technique makes use of the non-linear rf-SET transconductance to mix high frequency gate signals and produce difference-frequency components that fall within the bandwidth of the rf-SET. At gate frequencies >15GHz the induced charge on the rf-SET island is altered on time-scales faster than the inverse tunnel rate, preventing mixer operation. We suggest the possibility of utilizing this technique to sense h…
We report on fabrication of single-electron transistors using InAs nanowires with epitaxial aluminium with fixed tunnel barriers made of aluminium oxide. The devices exhibit a hard superconducting gap induced by the proximized aluminium cover shell and they behave as metallic single-electron transistors. In contrast to the typical few channel contacts in semiconducting devices, our approach forms opaque multichannel contacts to a semiconducting wire and thus provides a complementary way to study them. In addition, we confirm that unwanted extra quantum dots can appear at the surface of the nan…
In-plane heterojunction tunnel field effect transistors based on monolayer transition metal dichalcogenides are studied by means of self-consistent non-equilibrium Green's functions simulations and an atomistic tight-binding Hamiltonian. We start by comparing several heterojunctions before focusing on the most promising ones, i.e WTe2-MoS2 and MoTe2-MoS2. The scalability of those devices as a function of channel length is studied, and the influence of backgate voltages on device performance is analysed. Our results indicate that, by fine-tuning the design parameters, those devices can yield ex…
The Bloch-oscillating transistor (BOT) is an amplifier that utilizes semiclassical dynamics of states in energy bands under traveling quasimomentum. In a BOT, a single quasiparticle tunneling across a base tunnel junction switches the state of a superconducting tunnel junction to a lower Bloch band, triggering a series of resonant Cooper-pair tunnelings through an emitter Josephson junction (Bloch oscillations). Here, we investigate experimentally and theoretically an alternative realization of this device, based only on superconducting tunnel junctions. We discover new amplification schemes, …
The linear conductance of the single electron transistor is determined in the high temperature limit. Electron tunneling is treated nonperturbatively by means of a path integral formulation and the conductance is obtained from Kubo's formula. The theoretical predictions are valid for arbitrary conductance and found to explain recent experimental data.
The continuous down-scaling of transistors has been the key to the successful development of current information technology. However, with Moore's law reaching its limits, the development of alternative transistor architectures is urgently needed. Transistors require a switching voltage of at least 60 mV for each tenfold increase in current, that is, a subthreshold swing (SS) of 60 mV per decade (dec). Alternative tunnel field-effect transistors (TFETs) are widely studied to achieve a sub-thermionic SS and high I60 (the current where SS becomes 60 mV/dec). Heterojunction (HJ) TFETs show promis…
The performance of electronic and spintronic devices based on two-dimensional semiconductors (2D SC) is largely dependent on the quality and resistance of the metal/SC electrical contacts, as well as preservation of the intrinsic properties of the SC channel. Direct Metal/SC interaction results in highly resistive contacts due to formation of large Schottky barriers and considerably affects the properties of the 2D SC. In this work, we address these two important issues in monolayer $\mathrm{MoSe_2}$ Field-Effect transistors (FETs). We encapsulate the $\mathrm{MoSe_2}$ channel with hexagonal B…
The single particle tunneling in a vertical stack consisting of monolayers of two-dimensional semiconductors is studied theoretically and its application to a novel Two-dimensional Heterojunction Interlayer Tunneling Field Effect Transistor (Thin-TFET) is proposed and described. The tunneling current is calculated by using a formalism based on the Bardeen's transfer Hamiltonian, and including a semi-classical treatment of scattering and energy broadening effects. The misalignment between the two 2D materials is also studied and found to influence the magnitude of the tunneling current, but hav…
A new compact modeling approach is presented which describes the full current-voltage (I-V) characteristic of high-performance (aggressively scaled-down) tunneling field-effect-transistors (TFETs) based on homojunction direct-bandgap semiconductors. The model is based on an analytic description of two key features, which capture the main physical phenomena related to TFETs: 1) the potential profile from source to channel, and 2) the elliptic curvature of the complex bands in the bandgap region. It is proposed to use 1D Poisson's equations in the source and the channel to describe the potential…
A model of a superconducting tunnel junction which refrigerates a nearby metallic island without any particle exchange is presented. Heat extraction is mediated by charge fluctuations in the coupling capacitance of the two systems. The interplay of Coulomb interaction and the superconducting gap reduces the power consumption of the refrigerator. The island is predicted to be cooled from lattice temperatures of 200~mK down to close to 50~mK, for realistic parameters. The results emphasize the role of non-equilibrium correlations in bipartite mesoscopic conductors. This mechanism can be applied …
A superconducting tunnel junction is used to directly extract quasiparticles from one of the leads of a single-Cooper-pair-transistor. The consequent reduction in quasiparticle density causes a lower rate of quasiparticle tunneling onto the device. This rate is directly measured by radio-frequency reflectometry. Local cooling may be of direct benefit in reducing the effect of quasiparticles on coherent superconducting nanostructures.
We investigate the behavior of both pure spin and spin-polarized currents measured with four probe non-local and two probe local configurations up to room temperature and under external gate voltage in a lateral graphene transistor, produced using a standard large-scale microfabrication process. The high spin diffusion length of pristine graphene in the channel, measured both directly and by the Hanle effect, and the tuning of relation between electrode resistance area present in the device architecture, allowed us to observe local tunnel magnetoresistance at room temperature, a new finding fo…
We report the use of plasma-enhanced atomic layer deposition (PEALD) to fabricate single-electron transistors (SETs) featuring ultra-thin (~1 nm) tunnel-transparent SiO2 in Ni-SiO2-Ni tunnel junctions. We show that as a result of the O2 plasma steps in PEALD of SiO2, the top surface of the underlying Ni electrode is oxidized. Additionally, the bottom surface of the upper Ni layer is also oxidized where it is in contact with the deposited SiO2, most likely as a result of oxygen-containing species on the surface of the SiO2. Due to the presence of these surface parasitic layers of NiO, which exh…
