Carbon nanotube mechanical resonators have attracted considerable interest because of their small mass, the high quality of their surface, and the pristine electronic states they host. However, their small dimensions result in fragile vibrational states that are difficult to measure. Here we observe quality factors $Q$ as high as $5\times10^6$ in ultra-clean nanotube resonators at a cryostat temperature of 30 mK, where we define $Q$ as the ratio of the resonant frequency over the linewidth. Measuring such high quality factors requires both employing an ultra-low noise method to detect minuscule vibrations rapidly, and carefully reducing the noise of the electrostatic environment. We observe that the measured quality factors fluctuate because of fluctuations of the resonant frequency. The quality factors we measure are record high; they are comparable to the highest $Q$ reported in mechanical resonators of much larger size, a remarkable result considering that reducing the size of resonators is usually concomitant with decreasing quality factors. The combination of ultra-low size and very large $Q$ offers new opportunities for ultra-sensitive detection schemes and quantum optomechanical experiments.
We report on a simple method to fabricate high-frequency nanotube mechanical resonators reproducibly. We measure resonance frequencies as high as 4.2 GHz for the fundamental eigenmode and 11 GHz for higher order eigenmodes. The high-frequency resonances are achieved using short suspended nanotubes and by introducing tensile stress in the nanotube. These devices allow us to determine the coefficient of the thermal expansion of an individual nanotube, which is negative and is about -0.7E-5 1/K at room temperature. High-frequency resonators made of nanotubes hold promise for mass sensing and expe…
We report the capacitive spring softening effect observed in single-walled carbon nanotube (SWNT) nanoelectromechanical (NEM) resonators. The nanotube resonators adopt dual-gate configuration with both bottom-gate and side-gate capable of tuning the resonance frequency through capacitive coupling. Interestingly, downward resonance frequency shifting is observed with increasing side-gate voltage, which can be attributed to the capacitive softening of spring constant. Furthermore, in-plane vibrational modes exhibit much stronger spring softening effect than out-of-plan modes. Our dual-gate desig…
Nanotubes behave as semi-flexible polymers in that they can bend by a sizeable amount. When integrating a nanotube in a mechanical resonator, the bending is expected to break the symmetry of the restoring potential. Here we report on a new detection method that allows us to demonstrate such symmetry breaking. The method probes the motion of the nanotube resonator at nearly zero-frequency; this motion is the low-frequency counterpart of the second overtone of resonantly excited vibrations. We find that symmetry breaking leads to the spectral broadening of mechanical resonances, and to an appare…
The low quality factor (Q) of Single-walled carbon nanotube (SWNT) resonators has limited their sensitivity in sensing application. To this end, we employ the technique of parametric amplification by modulating the spring constant of SWNT resonators at twice the resonant frequency, and achieve 10 times Q enhancement. The highest Q obtained at room temperature is around ~700, which is 3-4 times better than previous Q record reported for doubly-clamped SWNT resonators. Furthermore, efficient parametric amplification is found to only occur in the catenary vibration regime. Our results open up the…
Mechanical resonators based on low-dimensional materials provide a unique platform for exploring a broad range of physical phenomena. The mechanical vibrational states are indeed extremely sensitive to charges, spins, photons, and adsorbed masses. However, the roadblock is often the readout of the resonator, since the detection of the vibrational states becomes increasingly difficult for smaller resonators. Here, we report an unprecedentedly sensitive method to detect nanotube resonators with effective masses in the 10^-20 kg range. We use the beam of an electron microscope to resolve the mech…
Carbon nanotubes and graphene allow fabricating outstanding nanomechanical resonators. They hold promise for various scientific and technological applications, including sensing of mass, force, and charge, as well as the study of quantum phenomena at the mesoscopic scale. Here, we have discovered that the dynamics of nanotube and graphene resonators is in fact highly exotic. We propose an unprecedented scenario where mechanical dissipation is entirely determined by nonlinear damping. As a striking consequence, the quality factor Q strongly depends on the amplitude of the motion. This scenario …
Coupling an electromechanical resonator with carbon-nanotube quantum dots is a significant method to control both the electronic charge and the spin quantum states. By exploiting a novel micro-transfer technique, we fabricate two strongly-coupled and electrically-tunable mechanical resonators on a single carbon nanotube for the first time. The frequency of the two resonators can be individually tuned by the bottom gates, and strong coupling is observed between the electron charge and phonon modes of each resonator. Furthermore, the conductance of either resonator can be nonlocally modulated by…
We report on an electrical detection method of ultrasensitive carbon nanotube mechanical resonators. The noise floor of the detection method is reduced using a RLC resonator and an amplifier based on a high electron mobility transistor cooled at 4.2 K. This allows us to resolve the resonance frequency of nanotube resonators with an unprecedented quality. We show that the noise of the resonance frequency measured at 4.2 K is limited by the resonator itself, and not by the imprecision of the measurement. The Allan deviation reaches ~10^-5 at 125 ms integration time. When comparing the integratio…
We have observed the transversal vibration mode of suspended carbon nanotubes at millikelvin temperatures by measuring the single-electron tunneling current. The suspended nanotubes are actuated contact-free by the radio frequency electric field of a nearby antenna; the mechanical resonance is detected in the time-averaged current through the nanotube. Sharp, gate-tuneable resonances due to the bending mode of the nanotube are observed, combining resonance frequencies of up to ν_0 = 350 MHz with quality factors above Q = 10^5, much higher than previously reported results on suspended carbon na…
We study electron mechanical coupling in a suspended carbon nanotube (CNT) quantum dot device. Electron spin couples to the flexural vibration mode due to spin-orbit coupling in the electron tunneling processes. In the weak coupling limit, i.e. electron-vibration coupling is much smaller than the electron energy scale, the damping and resonant frequency shift of the CNT resonator can be obtained by calculating the dynamical spin susceptibility. We find that strong spin-flip scattering processes in Kondo regime significantly affect the mechanical motion of the carbon nanotube: Kondo effect indu…
Mechanical resonators based on a single carbon nanotube are exceptional sensors of mass and force. The force sensitivity in these ultra-light resonators is often limited by the noise in the detection of the vibrations. Here, we report on an ultra-sensitive scheme based on a RLC resonator and a low-temperature amplifier to detect nanotube vibrations. We also show a new fabrication process of electromechanical nanotube resonators to reduce the separation between the suspended nanotube and the gate electrode down to $\sim 150$~nm. These advances in detection and fabrication allow us to reach $0.5…
A hallmark of mechanical resonators made from a single nanotube is that the resonance frequency can be widely tuned. Here, we take advantage of this property to realize parametric amplification and self-oscillation. The gain of the parametric amplification can be as high as 18.2 dB and tends to saturate at high parametric pumping due to nonlinear damping. These measurements allow us to determine the coefficient of the linear damping force. The corresponding damping rate is lower than the one obtained from the lineshape of the resonance (without pumping), supporting the recently reported scenar…
The RF-response of a three-terminal carbon nanotube resonator coupled to RF-transmission lines is studied by means of perturbation theory and direct numerical integration. We find three distinct oscillatory regimes, including one regime capable of exhibiting very large hysteresis loops in the frequency response. Considering a purely capacitive transduction, we derive a set of algebraic equations which can be used to find the output power (S-parameters) for a device connected to transmission lines with characteristic impedance $Z_0$.
Since the advent of atomic force microscopy, mechanical resonators have been used to study a wide variety of phenomena, such as the dynamics of individual electron spins, persistent currents in normal metal rings, and the Casimir force. Key to these experiments is the ability to measure weak forces. Here, we report on force sensing experiments with a sensitivity of 12 zN Hz^(-1/2) at a temperature of 1.2 K using a resonator made of a carbon nanotube. An ultra-sensitive method based on cross-correlated electrical noise measurements, in combination with parametric downconversion, is used to dete…
In physical systems, decoherence can arise from both dissipative and dephasing processes. In mechanical resonators, the driven frequency response measures a combination of both, while time domain techniques such as ringdown measurements can separate the two. Here, we report the first observation of the mechanical ringdown of a carbon nanotube mechanical resonator. Comparing the mechanical quality factor obtained from frequency- and time-domain measurements, we find a spectral quality factor four times smaller than that measured in ringdown, demonstrating dephasing-induced decoherence of the na…
A suspended, doubly clamped single wall carbon nanotube is characterized as driven nano-electromechanical resonator at cryogenic temperatures. Electronically, the carbon nanotube displays small bandgap behaviour with Coulomb blockade oscillations in electron conduction and transparent contacts in hole conduction. We observe the driven mechanical resonance in dc-transport, including multiple higher harmonic responses. The data shows a distinct negative frequency tuning at finite applied gate voltage, enabling us to electrostatically decrease the resonance frequency to 75% of its maximum value. …
Bending-mode vibrations of carbon nanotube resonator devices were mechanically detected in air at atmospheric pressure by means of a novel scanning force microscopy method. The fundamental and higher order bending eigenmodes were imaged at up to 3.1GHz with sub-nanometer resolution in vibration amplitude. The resonance frequency and the eigenmode shape of multi-wall nanotubes are consistent with the elastic beam theory for a doubly clamped beam. For single-wall nanotubes, however, resonance frequencies are significantly shifted, which is attributed to fabrication generating, for example, slack…
Carbon nanotubes (CNTs) are nonlinear high-Q resonators with strong coupling to single-electron tunneling. We begin by describing several methods to detect the flexural motion of a CNT resonator. Next, we illustrate how single-electron tunneling in quantum dot CNT resonators leads to sharp dips in the mechanical resonance frequency and significant damping. We discuss four different contributions to the nonlinear oscillation of a CNT resonator: beam-like mechanical nonlinearity, nonlinearity due to gate-induced mechanical tension, electrostatic nonlinearity, and nonlinearity due to single-elect…
By first lithographically fabricating contact electrodes and then as last step growing carbon nanotubes with chemical vapour deposition across the ready-made chip, many potential contamination mechanisms for nanotube devices can be avoided. Combining this with pre-defined trenches on the chip, such that the nanotubes are freely suspended above the substrate, enables the formation of highly regular electronic systems. We show that, in addition, such suspended ultra-clean nanotubes provide excellent high-frequency and low-dissipation mechanical resonators. The motion detection mechanism of our e…
We investigate the role that noise plays in the hysteretic dynamics of a suspended nanotube or a graphene sheet subject to an oscillating force. We find that not only the size but also the position of the hysteresis region in these systems can be controlled by noise. We also find that nano-resonators act as noise rectifiers: by increasing the noise in the setup, the resonance width of the characteristic peak in these systems is reduced and, as a result, the quality factor is increased.
The non-linear interaction between two mechanical resonances of the same freely suspended carbon nanotube resonator is studied. We find that in the Coulomb blockade regime, the non-linear modal interaction is dominated by single-electron-tunneling processes, and that the mode-coupling parameter can be tuned with the gate voltage, allowing both mode softening and mode stiffening behavior. This is in striking contrast to tension-induced mode coupling in strings, where the coupling parameter is positive and gives rise to a stiffening of the mode. The strength of the mode coupling in carbon nanotu…
Graphene and carbon nanotubes represent the ultimate size limit of one and two-dimensional nanoelectromechanical resonators. Because of their reduced dimensionality, graphene and carbon nanotubes display unusual mechanical behavior; in particular, their dynamics is highly nonlinear. Here, we review several types of nonlinear behavior in resonators made from nanotubes and graphene. We first discuss an unprecedented scenario where damping is described by a nonlinear force. This scenario is supported by several experimental facts: (i) the quality factor varies with the amplitude of the motion as …
A suspended, doubly clamped single wall carbon nanotube is characterized at cryogenic temperatures. We observe specific switching effects in dc-current spectroscopy of the embedded quantum dot. These have been identified previously as nano-electromechanical self-excitation of the system, where positive feedback from single electron tunneling drives mechanical motion. A magnetic field suppresses this effect, by providing an additional damping mechanism. This is modeled by eddy current damping, and confirmed by measuring the resonance quality factor of the rf-driven nano-electromechanical resona…
When a contaminant diffuses on the surface of a nanomechanical resonator, the motions of the two become correlated. Despite being a high-order effect in the resonator-particle coupling, such correlations affect the system dynamics by inducing dissipation of the resonator energy. Here, we consider this diffusion-induced dissipation in the cases of multiple particles adsorbed on carbon nanotube and graphene resonators. By solving the stochastic equations of motion, we simulate the ringdown of the resonator, in order to determine the resonator energy decay rate. We find two different scalings wit…
We report on the fabrication and operation of a multi-element vibrational structure consisting of two graphene mechanical resonators coupled by a nanotube beam. The whole structure is suspended. Each graphene resonator is clamped by two metal electrodes. The structure is fabricated using a combination of electron-beam lithography and atomic-force microscopy nano-manipulation. This layout allows us to detect the mechanical vibrations electrically. The measured eigenmodes are localized in either one of the graphene resonators. The coupling due to the nanotube is studied by measuring the shift of…
We studied monolayers of noble gas atoms (Xe, Kr, Ar, and Ne) deposited on individual ultra- clean suspended nanotubes. For this, we recorded the resonance frequency of the mechanical motion of the nanotube, since it provides a direct measure of the coverage. The latter is the number of adsorbed atoms divided by the number of the carbon atoms of the suspended nanotube. Monolayers formed when the temperature was lowered in a constant pressure of noble gas atoms. The coverage of Xe monolayers remained constant at 1/6 over a large temperature range. This finding reveals that Xe monolayers are sol…
Nanomechanical resonators are used with great success to couple mechanical motion to other degrees of freedom, such as photons, spins, and electrons. Mechanical vibrations can be efficiently cooled and amplified using photons, but not with other degrees of freedom. Here, we demonstrate a simple yet powerful method for cooling, amplification, and self-oscillation using electrons. This is achieved by applying a constant (DC) current of electrons through a suspended nanotube in a dilution fridge. We demonstrate cooling down to $4.6\pm 2.0$ quanta of vibrations. We also observe self-oscillation, w…
Carbon nanotubes (CNTs) have attracted much attention for use in nanomechanical devices because of their exceptional properties, such as large resonant frequencies, low mass, and high quality factors. Here, we report the first experimental realization of parametric strong coupling between two mechanical modes on a single CNT nanomechanical resonator, by applying an extra microwave pump. This parametric pump method can be used to couple mechanical modes with arbitrary frequency differences. The properties of the mechanical resonator are detected by single-electron tunneling at low temperature, …
Electromechanical resonators are a key element in radio-frequency telecommunications devices and thus new resonator concepts from nanotechnology can readily find important industrial opportunities. In this paper, we report the successful experimental realization of AM, FM and digital demodulation with suspended single wall carbon nanotube resonators in the field effect transistor configuration. The crucial role played by the mechanical resonance in demodulation is clearly demonstrated. The FM technique is shown to lead to the suppression of unwanted background signals and the reduction of nois…
In this work, we present a detailed static and dynamic analysis of a recently reported electrically actuated buckled carbon nanotube (CNT) resonator, based on the Euler-Bernoulli beam theory. The system behavior is analyzed using the Galerkin reduced order model. We show that a simple single-modal analysis can already predict snap-through bi-stability in a buckled CNT resonator. However, we prove that the experimental data, in which the snap-through buckling occurs at a finite frequency, cannot be explained without taking into account out-of-plane motion. The buckled CNTs are the first type of…
We report on the nonlinear coupling between the mechanical modes of a nanotube resonator. The coupling is revealed in a pump-probe experiment where a mode driven by a pump force is shown to modify the motion of a second mode measured with a probe force. In a second series of experiments, we actuate the resonator with only one oscillating force. Mechanical resonances feature exotic lineshapes with reproducible dips, peaks, and jumps when the measured mode is commensurate with another mode with a frequency ratio of either 2 or 3. Conventional lineshapes are recovered by detuning the frequency ra…
We propose a technique for sensitive magnetic point force detection using a suspended carbon nanotube (CNT) mechanical resonator combined with a magnetic field gradient generated by a ferromagnetic gate electrode. Numerical calculations of the mechanical resonance frequency show that single Bohr magneton changes in the magnetic state of an individual magnetic molecule grafted to the CNT can translate to detectable frequency shifts, on the order of a few kHz. The dependences of the resonator response to device parameters such as length, tension, CNT diameter, and gate voltage are explored and o…
In an optomechanical setup, the coupling between cavity and resonator can be increased by tuning them to the same frequency. We study this interaction between a carbon nanotube resonator and a radio-frequency circuit. In this resonant regime, the vacuum optomechanical coupling is enhanced by the DC voltage coupling the cavity and the mechanical resonator. Using the cavity to detect the nanotube's motion, we observe and simulate interference between mechanical and electrical oscillations. We measure the mechanical ring-down and show that further improvements to the system could enable measureme…
Different damping mechanisms in graphene nanoresonators are studied: charges in the substrate, ohmic losses in the substrate and the graphene sheet, breaking and healing of surface bonds (Velcro effect), two level systems, attachment losses, and thermoelastic losses. We find that, for realistic structures and contrary to semiconductor resonators, dissipation is dominated by ohmic losses in the graphene layer and metallic gate. An extension of this study to carbon nanotube-based resonators is presented.
Helium is recognized as a model system for the study of phase transitions. Of particular interest is the superfluid phase in two dimensions. We report measurements on superfluid helium films adsorbed on the surface of a suspended carbon nanotube. We measure the mechanical vibrations of the nanotube to probe the adsorbed helium film. We demonstrate the formation of helium layers up to five atoms thickness. Upon increasing the vapour pressure, we observe layer-by-layer growth with discontinuities in both the number of adsorbed atoms and the speed of sound in the adsorbed film. These hitherto uno…
Carbon nanotube (CNT) electromechanical resonators have demonstrated unprecedented sensitivities for detecting small masses and forces. The detection speed in a cryogenic setup is usually limited by the CNT contact resistance and parasitic capacitance. We report the use of a heterojunction bipolar transistor (HBT) amplifying circuit near the device to measure the mechanical amplitude at microsecond timescales. A Coulomb rectification scheme, in which the probe signal is at much lower frequency than the mechanical drive signal, allows investigation of the strongly non-linear regime. The behavio…
We have fabricated suspended metal paddle resonators with carbon nanotubes functioning as self-detecting torsional springs. We observe gate-tunable resonances, that either tune to higher or to lower frequencies when increasing the dc voltage on the back-gate. We attribute the former modes to flexural vibrations of the paddle resonator, while the latter ones are identified as torsional vibrations. Compared to top-down silicon fabricated paddle resonators, nanotube springs have smaller torsional spring constants and provide a larger frequency tunability.
Single-walled carbon nanotubes have advantages as a nanoscale light source compatible with silicon photonics because they show room-temperature luminescence at telecom-wavelengths and can be directly synthesized on silicon substrates. Here we demonstrate integration of individual light-emitting carbon nanotubes with silicon microdisk resonators. Photons emitted from nanotubes are efficiently coupled to whispering gallery modes, circulating within the disks and lighting up their perimeters. Furthermore, we control such emission by tuning the excitation wavelength in and out of resonance with hi…
We simulated the behavior of suspended carbon-nanotube (CNT) resonators over a broad range of temperatures to address the unexplained spectral broadening and frequency shifts seen in experiments. We find that thermal fluctuations induce strong coupling between resonance modes. This effect leads to spectral fluctuations which readily account for the experimentally observed quality factors $Q\sim100$ at $300\ K$. Using a mean field approach to describe entropic fluctuations we analytically calculate $Q$ and frequency shifts in tensioned and buckled CNTs and find excellent agreement with simulati…
The in-place growth of suspended carbon nanotubes facilitates the observation of both unperturbed electronic transport spectra and high-Q vibrational modes. For complex structures integrating, e.g., superconducting rf elements on-chip, selection of a chemically and physically resistant material that survives the chemical vapor deposition (CVD) process provides a challenge. We demonstrate the implementation of molybdenum-rhenium coplanar waveguide resonators that exhibit clear resonant behaviour at cryogenic temperatures even after having been exposed to nanotube growth conditions. The properti…
Bi-stable mechanical resonators play a significant role in various applications, such as sensors, memory elements, and quantum computing. While carbon nanotube (CNT) based resonators have been widely investigated as promising nano electro-mechanical devices, a bi-stable CNT resonator has never been demonstrated. Here, we report a new class of CNT resonators in which the nanotube is buckled upward. We show that a small upward buckling yields record electrical frequency tunability, whereas larger buckling can achieve Euler-Bernoulli (EB) bi-stability, the smallest mechanical resonator with two s…
Molybdenum rhenium alloy thin films can exhibit superconductivity up to critical temperatures of $T_c=15\mathrm{K}$. At the same time, the films are highly stable in the high-temperature methane / hydrogen atmosphere typically required to grow single wall carbon nanotubes. We characterize molybdenum rhenium alloy films deposited via simultaneous sputtering from two sources, with respect to their composition as function of sputter parameters and their electronic dc as well as GHz properties at low temperature. Specific emphasis is placed on the effect of the carbon nanotube growth conditions on…
We study the optical properties of MoS$_2$ nanotubes (NTs) with walls comprising dozens of monolayers. We reveal strong peaks in micro-photoluminescence ($μ$-PL) spectra when detecting the light polarized along the NT axis. We develop a model describing the optical properties of the nanotubes acting as optical resonators which support the quantization of whispering gallery modes inside the NT wall. The experimental observation of the resonances in $μ$-PL allows one to use them as a contactless method of the estimation of the wall width. Our findings open a way to use such NTs as polarization-s…
We study spin-dependent transport in a suspended carbon nanotube quantum dot in contact with two ferromagnetic leads and with the dot's spin coupled to the flexural mechanical modes. The spin-vibration interaction induces spin-flip processes between the two energy levels of the dot. This interaction arises from the spin-orbit coupling or a magnetic field gradient. The inelastic vibration-assisted spin flips give rise to a mechanical damping and, for an applied bias voltage, to a steady nonequilibrium occupation of the harmonic oscillator. We analyze these effects as function of the energy-leve…
Bi-stable arched beams exhibiting Euler-Bernoulli snap-through buckling are vastly used as electronic devices in various applications, such as memory devices, energy harvesters, sensors, and actuators. Recently, we reported the realization of the smallest bi-stable resonator to date, in the form of a buckled suspended carbon nanotube (CNT), which exhibits a unique three-dimensional snap-through transition and an extremely large change in frequency as a result. In this article, we address a unique characteristic of these devices, in which a significant change in the DC conductance is also obser…
Single-parameter adiabatic charge pumping, induced by a nearby radio-frequency antenna, is achieved in suspended carbon nanotubes close to the mechanical resonance. The charge pumping is due to an important dynamic adjustment of the oscillating motion to the antenna signal and it is different from the mechanism active in the two-parameter pumping. Finally, the second harmonic oscillator response shows an interesting relationship with the first harmonic that should be experimentally observed.
A suspended carbon nanotube can act as a nanoscale resonator with remarkable electromechanical properties and the ability to detect adsorption on its surface at the level of single atoms. Understanding adsorption on nanotubes and other graphitic materials is key to many sensing and storage applications. Here we show that nanotube resonators offer a powerful new means of investigating fundamental aspects of adsorption on carbon, including the collective behaviour of adsorbed matter and its coupling to the substrate electrons. By monitoring the vibrational resonance frequency in the presence of …
The quantum behaviour of mechanical resonators is a new and emerging field driven by recent experiments reaching the quantum ground state. The high frequency, small mass, and large quality-factor of carbon nanotube resonators make them attractive for quantum nanomechanical applications. A common element in experiments achieving the resonator ground state is a second quantum system, such as coherent photons or superconducting device, coupled to the resonators motion. For nanotubes, however, this is a challenge due to their small size. Here, we couple a carbon nanoelectromechanical (NEMS) device…
The coupling between electrons and phonons is at the heart of many fundamental phenomena in physics. In nature, this coupling is generally predetermined for both, molecules and solids. Tremendous advances have been made in controlling electrons and phonons in engineered nanosystems, yet, control over the coupling between these degrees of freedom is still widely lacking. Here, we use a new generation of carbon nanotube devices with movable ultra-clean single and double quantum dots embedded in a mechanical resonator to demonstrate the tailoring of the interactions between electronic and mechani…
Nanoelectromechanical systems (NEMS) have generated considerable interest as inertial mass sensors. NEMS resonators have been used to weigh cells, biomolecules, and gas molecules, creating many new possibilities for biological and chemical analysis [1-4]. Recently, NEMS-based mass sensors have been employed as a new tool in surface science in order to study e.g. the phase transitions or the diffusion of adsorbed atoms on nanoscale objects [5-7]. A key point in all these experiments is the ability to resolve small masses. Here we report on mass sensing experiments with a resolution of 1.7 yg (1…
We present nanofabrication and mechanical measurements of single-crystal diamond cantilevers with thickness down to 85 nm, thickness uniformity better than 20 nm, and lateral dimensions up to 240 um. Quality factors exceeding one million are found at room temperature, surpassing those of state-of-the-art single-crystal silicon cantilevers of similar dimensions by roughly an order of magnitude. Force sensitivities of a few hundred zeptonewtons result for the best cantilevers at millikelvin temperatures. Single-crystal diamond could thus directly improve existing force and mass sensors by a simp…
We demonstrate sensitive and fast electrical measurements of a carbon nanotube mechanical resonator. The nanotube is configured as a single-electron transistor, whose conductance is a sensitive transducer for its own displacement. Using an impedance-matching circuit followed by a cryogenic amplifier, the vibrations can be monitored in real time. The sensitivity of this continuous displacement measurement approaches within a factor 470 of the standard quantum limit.
Nanoscale resonators that oscillate at high frequencies are useful in many measurement applications. We studied a high-quality mechanical resonator made from a suspended carbon nanotube driven into motion by applying a periodic radio frequency potential using a nearby antenna. Single-electron charge fluctuations created periodic modulations of the mechanical resonance frequency. A quality factor exceeding 10^5 allows the detection of a shift in resonance frequency caused by the addition of a single-electron charge on the nanotube. Additional evidence for the strong coupling of mechanical motio…
We theoretically investigate the deflection-induced coupling of an electron spin to vibrational motion due to spin-orbit coupling in suspended carbon nanotube quantum dots. Our estimates indicate that, with current capabilities, a quantum dot with an odd number of electrons can serve as a realization of the Jaynes-Cummings model of quantum electrodynamics in the strong-coupling regime. A quantized flexural mode of the suspended tube plays the role of the optical mode and we identify two distinct two-level subspaces, at small and large magnetic field, which can be used as qubits in this setup. …
We demonstrate theoretically the feasibility of selective self-excitation of higher-mode flexural vibrations of graphene nano-ribbons and carbon nanotubes by the means of magnetomotive instability. Apart from the mechanical resonator, the device consists only of a constant voltage source, an inductor, a capacitor, a gate electrode and a constant magnetic field. Numerical simluations were performed on both graphene and carbon nanotubes displaying an overall similar behaviour, but with some differences arising mainly due to the non-linear mechanical bending forces. The advantages and disadvantag…
Synthesized micro- and nanotubes composed of transition metal dichalcogenides (TMDCs) such as MoS$_2$ are promising for many applications in nanophotonics, because they combine the abilities to emit strong exciton luminescence and to act as whispering gallery microcavities even at room temperature. In addition to tubes in the form of hollow cylinders, there is an insufficiently-studied class of twisted tubes, the flattened cross section of which rotates along the tube axis. As shown by theoretical analysis, in such nanotubes the interaction of electromagnetic waves excited at opposite sides of…
We investigate the efficiency of cooling the vibrations of a nano-mechanical resonator, constituted by a partially suspended Carbon-nanotube and operating as double-quantum dot. The motion is brought to lower temperatures by tailoring the energy exchange via electromechanical coupling with single electrons, constantly flowing through the nanotube when a constant potential difference is applied at its extremes in the Coulomb-blockade regime. Ground-state cooling is possible at sufficiently high quality factors, provided that the dephasing rate of electron transport within the double dot does no…
We report fast readout of the motion of a carbon nanotube mechanical resonator. A close-proximity high electron mobility transistor amplifier is used to increase the bandwidth of the measurement of nanotube displacements from the kHz to the MHz regime. Using an electrical detection scheme with the nanotube acting as a mixer, we detect the amplitude of its mechanical motion at room temperature with an intermediate frequency of 6 MHz and a timeconstant of 780 ns, both up to five orders of magnitude faster than achieved before. The transient response of the mechanical motion indicates a ring-down…
Single electron transistors (SETs) fabricated from single-walled carbon nanotubes (SWNTs) can be operated as highly sensitive charge detectors reaching sensitivity levels comparable to metallic radio frequency SETs (rf-SETs). Here we demonstrate how the charge sensitivity of the device can be improved by using the mechanical oscillations of a single-walled carbon nanotube quantum dot. To optimize the charge sensitivity $δQ$, we drive the mechanical resonator far into the nonlinear regime and bias it to an operating point where the mechanical third order nonlinearity is cancelled out. This way …
We report on a nanomechanical engineering method to monitor matter growth in real time via e-beam electromechanical coupling. This method relies on the exceptional mass sensing capabilities of nanomechanical resonators. Focused electron beam induced deposition (FEBID) is employed to selectively grow platinum particles at the free end of singly clamped nanotube cantilevers. The electron beam has two functions: it allows both to grow material on the nanotube and to track in real time the deposited mass by probing the noise-driven mechanical resonance of the nanotube. On the one hand, this detect…
