In this paper, we analyze the impact of relays on the uplink performance of FDMA cellular networks. We focus our analysis on Decode and Forward techniques, with the aim of measuring the improvements which can be achieved in terms of throughput and energy saving. We apply a stochastic geometry based approach to a scenario with inter-cell interference and reuse factor equal to 1. The first goal of this work is to observe what is the impact of various relay features, such as transmission power, location and antenna pattern, when a half-duplex constraint is imposed. The second goal is to determine how much relaying can be beneficial also for users who are not at the cell edge, and who can therefore use a direct link towards the base station. We show that if more refined decoding techniques, such as Successive Interference Cancellation and Superposition Coding, are properly used, considerable gains can be obtained for these mobiles as well.
In this paper, we develop novel two-tier interference management strategies that enable macrocell users (MUEs) to improve their performance, with the help of open-access femtocells. To this end, we propose a rate-splitting technique using which the MUEs optimize their uplink transmissions by dividing their signals into two types: a coarse message that is intended for direct transmission to the macrocell base station and a fine message that is decoded by a neighboring femtocell and subsequently relayed over a heterogeneous (wireless/wired) backhaul. For deploying the proposed technique, we form…
We consider Multi-User MIMO (MU-MIMO) scheduling in the 3GPP LTE-Advanced (3GPP LTE-A) cellular uplink. The 3GPP LTE-A uplink allows for precoded multi-stream (precoded MIMO) transmission from each scheduled user and also allows flexible multi-user (MU) scheduling wherein multiple users can be assigned the same time-frequency resource. However, exploiting these features is made challenging by certain practical constraints that have been imposed in order to maintain a low signaling overhead. We show that while the scheduling problem in the 3GPP LTE-A cellular uplink is NP-hard, it can be formul…
Ever since the inception of mobile telephony, the downlink and uplink of cellular networks have been coupled, i.e. mobile terminals have been constrained to associate with the same base station (BS) in both the downlink and uplink directions. New trends in network densification and mobile data usage increase the drawbacks of this constraint, and suggest that it should be revisited. In this paper we identify and explain five key arguments in favor of Downlink/Uplink Decoupling (DUDe) based on a blend of theoretical, experimental, and logical arguments. We then overview the changes needed in cur…
In this paper, using the stochastic geometry theory, we present a framework for analyzing the performance of device-to-device (D2D) communications underlaid uplink (UL) cellular networks. In our analysis, we consider a D2D mode selection criterion based on an energy threshold for each user equipment (UE). Specifically, a UE will operate in a cellular mode, if its received signal strength from the strongest base station (BS) is large than a threshold β. Otherwise, it will operate in a D2D mode. Furthermore, we consider a generalized log-normal shadowing in our analysis. The coverage probability…
Relay nodes-enhanced architectures are deemed a viable solution to enhance coverage and capacity of nowadays cellular networks. Besides a number of desirable features, these architectures reduce the average distance between users and network nodes, thus allowing for battery savings for users transmitting on the uplink. In this paper, we investigate the extent of these savings, by optimizing relay nodes deployment in terms of uplink energy consumption per transmitted bit, while taking into account a minimum uplink average user delay that has to be guaranteed. A novel performance evaluation fram…
This survey paper provides a detailed explanation of Long Term Evolution cellular network packet scheduling algorithms in both downlink and uplink directions. It starts by explaining the difference between Orthogonal Frequency Division Multiple Access that is used in downlink transmission, and Single Carrier Frequency Division Multiple Access is used in uplink. Then, it explains the difference between the LTE scheduling process in the donwlink and uplink through explaining the interaction between users and the scheduler. Then, it explains the most commonly used downlink and uplink scheduling a…
Device-to-device (D2D) communication has become one important part of the 5G cellular networks particularly due to the booming of proximity-based applications, e.g. D2D relays. However, the D2D relays may create strong interference to nearby users. Thus interference management in a cellular network with D2D relays is critical. In this paper, we study the optimal time reuse patterns in a cellular network with cooperative D2D relays and derive the corresponding optimized relaying strategies. Due to the binary association constraints and the fact that the total number of feasible time reuse patte…
This letter studies uplink transmission in large-scale cellular networks with a Type-II hybrid automatic repeat request (HARQ) retransmission scheme, under which an unsuccessful transmission (if occurs) is combined with the corresponding retransmission through maximum-ratio combining (MRC) for decoding. Based on stochastic geometry analysis, the uplink coverage probabilities are characterized under a generalized power control scheme in the scenarios with quasi-static interference (QSI) and fast-varying interference (FVI), where the same or different interfering users are present during the tra…
The evolution of mobile cellular networks has brought great changes of network architecture. For example, heterogeneous cellular network (HetNet) and Ultra dense network (UDN) have been proposed as promising techniques for 5G systems. Dense deployment of base stations (BSs) allows a mobile user to be able to access multiple BSs. Meanwhile the unbalance between UL and DL in HetNets, such as different received SINR threshold and traffic load, etc., becomes increasingly obvious. All these factors naturally inspire us to consider decoupling of uplink and downlink in radio access network. An intere…
In this paper, we consider resource allocation in the 3GPP Long Term Evolution (LTE) cellular uplink, which will be the most widely deployed next generation cellular uplink. The key features of the 3GPP LTE uplink (UL) are that it is based on a modified form of the orthogonal frequency division multiplexing based multiple access (OFDMA) which enables channel dependent frequency selective scheduling, and that it allows for multi-user (MU) scheduling wherein multiple users can be assigned the same time-frequency resource. In addition to the considerable spectral efficiency improvements that are …
A new design for two-hop opportunistic relaying in cellular networks is proposed, with the objective of throughput improvement. We propose using idle UEs in a cellular system with better channel to the base station to relay traffic for active UEs. One of the key ideas proposed is the use of (only) uplink spectrum for the Access links, and corresponding interference management schemes for managing interference between Access and Backhaul links. The proposed algorithms and architecture show a median throughput gain of 110% for downlink and 40% for uplink in system simulations performed according…
Simultaneous co-channel transmission and reception, denoted as in-band full duplex (FD) communication, has been promoted as an attractive solution to improve the spectral efficiency of cellular networks. However, in addition to the self-interference problem, cross-mode interference (i.e., between uplink and downlink) imposes a major obstacle for the deployment of FD communication in cellular networks. More specifically, the downlink to uplink interference represents the performance bottleneck for FD operation due to the uplink limited transmission power and venerable operation when compared to…
LTEs uplink (UL) efficiency critically depends on how the interference across different cells is controlled. The unique characteristics of LTEs modulation and UL resource assignment poses considerable challenges in achieving this goal because most LTE deployments have 1:1 frequency re-use, and the uplink interference can vary considerably across successive time slots. In this work, we propose LeAP, a measurement data driven machine learning paradigm for power control to manage up-link interference in LTE. The data driven approach has the inherent advantage that the solution adapts based on net…
We consider a two-hop cellular system in which the mobile nodes help the base station by relaying information to the dead spots. While two-hop cellular schemes have been analyzed previously, the distribution of the node locations has not been explicitly taken into account. In this paper, we model the node locations of the base stations and the mobile stations as a point process on the plane and then analyze the performance of two different two-hop schemes in the downlink. In one scheme the node nearest to the destination that has decoded information from the base station in the first hop is us…
We consider a cellular network where mobile transceiver devices that are owned by self-interested users are incentivized to cooperate with each other using tokens, which they exchange electronically to "buy" and "sell" downlink relay services, thereby increasing the network's capacity compared to a network that only supports base station-to-device (B2D) communications. We investigate how an individual device in the network can learn its optimal cooperation policy online, which it uses to decide whether or not to provide downlink relay services for other devices in exchange for tokens. We propo…
In this report, we consider how to dynamically select transmission bands and multi-hop routes for device-to-device (D2D) communications in co-existence with a cellular network overlay. Firstly, we consider different wireless routing algorithms, i.e. broadcasting-routing (BR) method, and shortest-path-routing (SPR) method. The results show that depending on the co-existence cellular users' outage constraint, different routing strategies have different merits. BR is acceptable at the low D2D user density but is terrible at high density. We also consider the channel band performance (Uplink band …
Fifth-generation cellular networks are expected to exhibit at least three primary physical-layer differences relative to fourth-generation ones: millimeter-wave propagation, antenna-array directionality, and densification of base stations. In this paper, the effects of these differences on the performance of single-carrier frequency-domain multiple-access uplink systems with frequency hopping are assessed. A new analysis, which is much more detailed than any other in the existing literature and accommodates actual base-station topologies, captures the primary features of uplink communications.…
In this paper, we provide an analytical framework to analyze the uplink performance of device-to-device (D2D)-enabled millimeter wave (mmWave) cellular networks. Signal-to- interference-plus-noise ratio (SINR) outage probabilities are derived for both cellular and D2D links using tools from stochastic geometry. The distinguishing features of mmWave communications such as directional beamforming and having different path loss laws for line-of-sight (LOS) and non-line-of-sight (NLOS) links are incorporated into the outage analysis by employing a flexible mode selection scheme and Nakagami fading…
This paper proposes a cellular network exploiting millimeter-wave (mmWave) and ultra-densified base stations (BSs) to achieve the far-reaching 5G aim in downlink average rate. The mmWave overlaid network however incurs a pitfall that its ample data rate is only applicable for downlink transmissions due to the implementation difficulty at mobile users, leading to an immense difference between uplink and downlink rates. We therefore turn our attention not only to maximize downlink rate but also to ensure the minimum uplink rate. With this end, we firstly derive the mmWave overlaid ultra-dense ce…
This paper reports relative performance of decode-and-forward (DF) and amplify-and-forward (AF) relaying in a multi-antenna cooperative cognitive radio network (CCRN) that supports device-to-device (D2D) communications using spectrum sharing technique in cellular network. In this work, cellular system is considered as primary and internet of things devices (IoDs), engaged in D2D communications, are considered to be secondary system. The devices access the licensed spectrum by means of the cooperation in two-way primary communications. Furthermore, IoDs are energized by harvesting the energy fr…
Wise arrangement of antennas is critical in wireless cellular systems for both reduction of co-channel interference (CCI) and increase the quality of service (QoS). In this paper, a novel architecture for antenna arrangement in CDMA wireless cellular systems is presented. In this architecture that we called microzone, every cell is divided into three (or more) zones and information transmission in downlink channel is done by an antenna which is placed at the outer region of the related zone. Also, the transmitting signal by the mobile station (MS) in uplink channel is received by all antennas …
Future wireless cellular networks must support both enhanced mobile broadband (eMBB) and ultra reliable low latency communication (URLLC) to manage heterogeneous data traffic for emerging wireless services. To achieve this goal, a promising technique is to enable flexible frame structure by dynamically changing the data frame's numerology according to the channel information as well as traffic quality of service requirements. However, due to nonorthogonal subcarriers, this technique can result in an interference, known as inter numerology interference (INI), thus, degrading the network perform…
The popularity of cellular internet of things (IoT) is increasing day by day and billions of IoT devices will be connected to the internet. Many of these devices have limited battery life with constraints on transmit power. High user power consumption in cellular networks restricts the deployment of many IoT devices in 5G. To enable the inclusion of these devices, 5G should be supplemented with strategies and schemes to reduce user power consumption. Therefore, we present a novel joint uplink user association and resource allocation scheme for minimizing user transmit power while meeting the q…
Device-to-device (D2D) communications as an underlay of a LTE-A (4G) network can reduce the traffic load as well as power consumption in cellular networks by way of utilizing peer-to-peer links for users in proximity of each other. This would enable other cellular users to increment their traffic, and the aggregate traffic for all users can be significantly increased without requiring additional spectrum. However, D2D communications may increase interference to cellular users (CUs) and force CUs to increase their transmit power levels in order to maintain their required quality-of-service (QoS…
Simultaneous reuse of spectral resources by uplink and downlink, denoted as in-band full duplex (FD) communication, is promoted to double the spectral efficiency when compared to its half-duplex (HD) counterpart. Interference management, however, remains challenging in FD cellular networks, especially when high disparity between uplink and downlink transmission powers exists. The uplink performance can be particularly deteriorated when operating on channels that are simultaneously occupied with downlink transmission. This paper considers a cellular wireless system with partial spectrum overlap…
By combining the concepts of superposition coding at the transmitter(s) and successive interference cancellation (SIC) at the receiver(s), non-orthogonal multiple access (NOMA) has recently emerged as a promising multiple access technique for 5G wireless technology. In this article, we first discuss the fundamentals of uplink and downlink NOMA transmissions and outline their key distinctions (in terms of implementation complexity, detection and decoding at the SIC receiver(s), incurred intra-cell and inter-cell interferences). Later, for both downlink and uplink NOMA, we theoretically derive t…
A wireless relay with multiple antennas is called a multiple-input-multiple-output (MIMO) switch if it maps its input links to its output links using "precode-and-forward." Namely, the MIMO switch precodes the received signal vector in the uplink using some matrix for transmission in the downlink. This paper studies the scenario of $K$ stations and a MIMO switch, which has full channel state information. The precoder at the MIMO switch is either a zero-forcing matrix or a network-coded matrix. With the zero-forcing precoder, each destination station receives only its desired signal with enhanc…
In this paper, we propose a transceiver architecture for full-duplex (FD) eNodeB (eNB) and FD user equipment (UE) transceiver. For FD communication,.i.e., simultaneous in-band uplink and downlink operation, same subcarriers can be allocated to UE in both uplink and downlink. Hence, contrary to traditional LTE, we propose using single-carrier frequency division multiple accesses (SC-FDMA) for downlink along with the conventional method of using it for uplink. The use of multiple antennas at eNB and singular value decomposition (SVD) in the downlink allows multiple users (MU) to operate on the s…
The forthcoming 5G cellular network is expected to overlay millimeter-wave (mmW) transmissions with the incumbent micro-wave (μW) architecture. The overall mm-μW resource management should therefore harmonize with each other. This paper aims at maximizing the overall downlink (DL) rate with a minimum uplink (UL) rate constraint, and concludes: mmW tends to focus more on DL transmissions while μW has high priority for complementing UL, under time-division duplex (TDD) mmW operations. Such UL dedication of μW results from the limited use of mmW UL bandwidth due to excessive power consumption and…
Using stochastic geometry, we develop a tractable uplink modeling paradigm for outage probability and spectral efficiency in both single and multi-tier cellular wireless networks. The analysis accounts for per user equipment (UE) power control as well as the maximum power limitations for UEs. More specifically, for interference mitigation and robust uplink communication, each UE is required to control its transmit power such that the average received signal power at its serving base station (BS) is equal to a certain threshold $ρ_o$. Due to the limited transmit power, the UEs employ a truncate…
Energy-aware system design is an important optimization task for static and mobile Internet of Things (IoT)-based sensor nodes, especially for highly resource-constrained vehicles such as mobile robotic systems. For 4G/5G-based cellular communication systems, the effective transmission power of uplink data transmissions is of crucial importance for the overall system power consumption. Unfortunately, this information is usually hidden within off-the-shelf modems and mobile handsets and can therefore not be exploited for enabling green communication. Moreover, the dynamic transmission power con…
The introduction of Narrowband Internet of Things (NB-IoT) as a cellular IoT technology aims to support massive Machine-Type Communications applications. These applications are characterized by massive connections from a large number of low-complexity and low-power devices. One of the goals of NB-IoT is to improve coverage extension beyond existing cellular technologies. In order to do that, NB-IoT introduces transmission repetitions and different bandwidth allocation configurations in uplink. These new transmission approaches yield many transmission options in uplink. In this paper, we propos…
The meta distribution of the signal-to-interference ratio (SIR) provides fine-grained information about the performance of individual links in a wireless network. This paper focuses on the analysis of the meta distribution of the SIR for both the cellular network uplink and downlink with fractional power control. For the uplink scenario, an approximation of the interfering user point process with a non-homogeneous Poisson point process is used. The moments of the meta distribution for both scenarios are calculated. Some bounds, the analytical expression, the mean local delay, and the beta appr…
Cellular uplink analysis has typically been undertaken by either a simple approach that lumps all interference into a single deterministic or random parameter in a Wyner-type model, or via complex system level simulations that often do not provide insight into why various trends are observed. This paper proposes a novel middle way using point processes that is both accurate and also results in easy-to-evaluate integral expressions based on the Laplace transform of the interference. We assume mobiles and base stations are randomly placed in the network with each mobile pairing up to its closest…
Multi-tier architecture improves the spatial reuse of radio spectrum in cellular networks, but it introduces complicated heterogeneity in the spatial distribution of transmitters, which brings new challenges in interference analysis. In this work, we present a stochastic geometric model to evaluate the uplink interference in a two-tier network considering multi-type users and base stations. Each type of tier-1 users and tier-2 base stations are modeled as independent homogeneous Poisson point processes, and tier-2 users are modeled as locally non-homogeneous clustered Poisson point processes c…
Non-orthogonal multiple access (NOMA) serves multiple users by superposing their distinct message signals. The desired message signal is decoded at the receiver by applying successive interference cancellation (SIC). Using the theory of Poisson cluster process (PCP), we provide a framework to analyze multi-cell uplink NOMA systems. Specifically, we characterize the rate coverage probability of a NOMA user who is at rank $m$ (in terms of the distance from its serving BS) among all users in a cell and the mean rate coverage probability of all users in a cell. Since the signal-to-interference-plu…
Device-to-device(D2D) underlaying communication brings great benefits to the cellular networks from the improvement of coverage and spectral efficiency at the expense of complicated transceiver design. With frequency spectrum sharing mode, the D2D user generates interference to the existing cellular networks either in downlink or uplink. Thus the resource allocation for D2D pairs should be designed properly in order to reduce possible interference, in particular for uplink. In this paper, we introduce a novel bandwidth allocation scheme to maximize the utilities of both D2D users and cellular …
Enabling high data-rate uplink cellular connectivity for drones is a challenging problem, since a flying drone has a higher likelihood of having line-of-sight propagation to base stations that terrestrial UEs normally do not have line-of-sight to. This may result in uplink inter-cell interference and uplink performance degradation for the neighboring ground UEs when drones transmit at high data-rates (e.g., video streaming). We address this problem from a cellular operator's standpoint to support drone-sourced video streaming of a point of interest. We propose a low-complexity, closed-loop con…
This paper considers a relay-assisted bidirectional cellular network where the base station (BS) communicates with each mobile station (MS) using OFDMA for both uplink and downlink. The goal is to improve the overall system performance by exploring the full potential of the network in various dimensions including user, subcarrier, relay, and bidirectional traffic. In this work, we first introduce a novel three-time-slot time-division duplexing (TDD) transmission protocol. This protocol unifies direct transmission, one-way relaying and network-coded two-way relaying between the BS and each MS. …
In cellular massive Machine-Type Communications (MTC), a device can transmit directly to the base station (BS) or through an aggregator (intermediate node). While direct device-BS communication has recently been in the focus of 5G/3GPP research and standardization efforts, the use of aggregators remains a less explored topic. In this paper we analyze the deployment scenarios in which aggregators can perform cellular access on behalf of multiple MTC devices. We study the effect of packet bundling at the aggregator, which alleviates overhead and resource waste when sending small packets. The agg…
Three-node full-duplex is a promising new transmission mode between a full-duplex capable wireless node and two other wireless nodes that use half-duplex transmission and reception respectively. Although three-node full-duplex transmissions can increase the spectral efficiency without requiring full-duplex capability of user devices, inter-node interference - in addition to the inherent self-interference - can severely degrade the performance. Therefore, as methods that provide effective self-interference mitigation evolve, the management of inter-node interference is becoming increasingly imp…
Employing multi-tier networks is among the most promising approaches to address the rapid growth of the data demand in cellular networks. In this paper, we study a two-tier uplink cellular network consisting of femtocells and a macrocell. Femto base stations, and femto and macro users are assumed to be spatially deployed based on independent Poisson point processes. We consider an open access assignment policy, where each macro user based on the ratio between its distances from its nearest femto access point (FAP) and from the macro base station (MBS) is assigned to either of them. By tuning t…
