The China Spallation Neutron Source (CSNS) uses H- stripping and phase space painting method to fill large ring acceptance with the linac beam of small emittance. The dependence of the painting beam on the injection beam parameters was studied for the Rapid Cycling Synchrotron (RCS) of CSNS. The injection processes for different momentum spread, rms emittance of the injection beam, injection beam matching were simulated, then the beam losses, 99% and rms emittances were obtained and the optimized ranges of injection beam parameters were given. The interaction between the H- beam and the stripping foil was studied and the foil scattering was simulated. Then, the stripping efficiency was calculated and the suitable thickness of the stripping foil was obtained. The energy deposition on the foil and the beam losses due to the foil scattering were also studied.
The Rapid Cycling Synchrotron (RCS) is a key component of the China Spallation Neutron Source (CSNS). For this type of high intensity proton synchrotron, the chromaticity, space charge effects and magnetic field tracking errors between the quadrupoles and the dipoles can induce beta function distortion and tune shift, and induce resonances. In this paper the combined effects of chromaticity, magnetic field tracking errors and space charge on beam dynamics at CSNS/RCS are studied systemically. 3-D simulations with different magnetic field tracking errors are performed by using the code ORBIT, a…
In the Rapid Cycling Synchrotron(RCS) of China Spallation Neutron Source(CSNS), transverse painting injection is employed to suppress the space-charge effects. The beta-beating caused by edge focusing of the injection bump magnets leads to tune shift and shrinkage of the acceptance, which may result in additional beam loss. In RCS, the main quadrupoles are excited by White resonant power supplies, and the exciting current cannot be arbitrarily programed. Generally, this kind of perturbation could be corrected by trim-quadrupole, however, we don't have trim-quadrupole in CSNS/RCS. A new method …
For the Rapid Cycling Synchrotron of China Spallation Neutron Source (CSNS/RCS), the stripping foil scattering generates the beam halo and gives rise to additional beam losses during the injection process. The interaction between the proton beam and the stripping foil was discussed and the foil scattering was studied. A simple model and the realistic situation of the foil scattering were considered. By using the codes ORBIT and FLUKA, the multi-turn phase space painting injection process with the stripping foil scattering for CSNS/RCS was simulated and the beam losses due to the foil scatterin…
CSNS/RCS accelerates a high-intensity proton beam from 80 MeV to 1.6 GeV. Since the beam current and beam power is high, the beam loading is a severe problem for the stability of the circulating beam in the RCS. To study the beam loading effect in the CSNS/RCS theoretically, the RLC circuit model of the rf cavity, the method of the Fast Fourier Transform and the method of Laplace transform have been employed to obtain the impedance of the rf system, the beam spectrum and the beam-induced voltage, respectively. Based on these physical models, the beam dynamics equations have been revised and a …
The rapid cycling synchrotron (RCS) is part of China Spallation Neutron Source (CSNS). The RCS provides 1.6GeV protons with a repetition rate of 25Hz. The RF system in RCS is mainly composed of a ferrite loaded RF cavity, a high power tetrode amplifier, a bias supply of 3300A and a digital low level RF (LLRF) system based on FPGA. The major challenge of the LLRF system is to solve problems caused by rapid frequency sweeping and heavy beam loading effect. This paper will present the design and structure of the LLRF system, and show results of performance tests.
The Robust Conjugate Direction Search (RCDS) method is used to optimize the collimation system for Rapid Cycling Synchrotron (RCS) of the Chinese Spallation Neutron Source (CSNS). The parameters of secondary collimators are optimized for a better performance of the collimation system. To improve the efficiency of the optimization, the Objective Ring Beam Injection and Tracking (ORBIT) parallel module combined with MATLAB parallel computing is used, which can run multiple ORBIT instances simultaneously. This study presents a way to figure out an optimal parameter combination of the secondary co…
The Rapid Cycling Synchrotron (RCS) in Chinese Spallation Neutron Source (CSNS) accelerates proton beam from 80Mev to 1.6GeV at a repetition rate of 25Hz. All dipole magnets of RCS are operated at AC with biased DC. Aiming at the properties of these dipole magnets, we take some methods to improve magnetic field quality in the good region and reduce eddy currents in the iron core . In this paper, we would present the process of the magnet design and temperature rise calculation. At the same time, the field measurement results and temperature test of the prototype magnet are also described and d…
China Spallation Neutron Source (CSNS) is a high intensity beam facility being built now in China. Three kicker assemblies, eight pulsed magnets, will be used in the CSNS rapid circle synchrotron (RCS). The physical and structural designs of eight kicker magnets that are grouped in 5 different types are presented. The results of OPERA-3D simulation show that magnet center field integral meet the physics requirements of design by choosing a suitable magnet coil structure. Field uniformity for 60% width is +/-0.7%. The ferrite magnet structure and composition is introduced, and the high voltage …
Precise measurement of betatron tune is required for good operating condition of CSNS RCS. The fractional part of betatron tune is important and it can be measured by analyzing the signals of beam position from the appointed BPM. Usually these signals are contaminated during the acquisition process, therefore several power spectrum methods are used to improve the frequency resolution. In this article classical and modern power spectrum methods are used. In order to compare their performance, the results of simulation data and IQT data from J-PARC RCS are discussed. It is shown that modern powe…
The China Spallation Neutron Source (CSNS) accelerator uses H- stripping and phase space painting method of filling large ring acceptance with the linac beam of small emittance. The beam commissioning software system is the key part of CSNS accelerator. The injection beam commissioning software for CSNS contains three parts currently: painting curve control, injection beam control and injection orbit correction. The injection beam control contains two subsections: single bunch beam calculation and LRBT beam control at the foil. The injection orbit correction also contains two subsections: inje…
A combination of the H- stripping and phase space painting method is used to accumulate a high intensity beam in the Rapid Cycling Synchrotron (RCS) of the China Spallation Neutron Source (CSNS). The injection system for CSNS/RCS consists of three kinds of magnets: four direct current magnets (BC1-BC4), eight alternating current magnets (BH1-BH4 and BV1-BV4), two septum magnets (ISEP1 and ISEP2). In this paper, the magnetic measurements of the injection system were introduced and the data analysis was processed. The field uniformity and magnetizing curves of these magnets were given, and then …
The dual harmonic system has been widely used in high intensity proton synchrotrons to suppress the space charge effect, as well as reduce the beam loss. To investigate the longitudinal beam dynamics in the dual rf system, the potential well, the sub-buckets in the bunch and the multi-solutions of the phase equation have been studied theoretically. Based on these theoretical studis, the optimization of bunching factor and rf voltage waveform are made for the dual harmonic rf system in the upgrade phase of the CSNS/RCS. In the optimization process, the simulation with space charge effect is don…
For the Rapid Cycling Synchrotron of the China Spallation Neutron Source (CSNS/RCS), the electron emission plays an important role in the accelerator limitation. The interactions between the proton beam and the stripping foil were studied, and the electron scattering processes were simulated by the ORBIT and FLUKA codes. Then, the electron energy distribution and the electron yielding rate can be given. Furthermore, the interactions between the proton beam and the collimation system were studied, and the electron scattering processes were simulated. Then, the energy distribution of the primary…
In a beam cycle, there is a chicane bump (BC bump) in the injection region of China Spallation Neutron Source (CSNS). It is a core part of the injection system and the important guarantee that the Linac beam injecting into the rapid cycling synchrotron (RCS). During the beam commissioning, the residual orbit of BC bump, i.e. the closedorbit distortion (COD) due to the imperfect BC bump, was an important problem which can affect the orbit correction and beam loss control of the RCS. In this paper, a method to measure the residual orbit of BC bump was studied and given. By using the three auxili…
For the China Spallation Neutron Source (CSNS), a combination of the H- stripping and phase space painting method is used to accumulate a high intensity beam in the Rapid Cycling Synchrotron (RCS). In this paper, firstly, the injection processes with different painting ranges and different painting methods were studied. With the codes ORBIT and MATLAB, the particle distribution and painting image were obtained. Then, the reasonable painting range which is suitable for the aperture size and magnet gap can be selected. Since the real field uniformity of BH3 and BV3 is not completely in conformit…
The Rapid Cycling Synchrotron(RCS) of China Spallation Neutron Source(CSNS) employs painting injection to achieve uniform beam distribution and suppress space-charge effects. In the painting injection, the mismatch between the injection beam orbit and circulating orbit could make the non-uniformity of beam distribution and emittance growth, which may lead to beam loss. To match the injection beam orbit and the circulating beam orbit, it is necessary to identify the orbit of injection beam relative to the circulating orbit in the injection point. However, it's hard to measure this relative inje…
The rapid cycling synchrotron (RCS) of the China Spallation Neutron Source (CSNS) is a high intensity proton ring with beam power of 100 kW. In order to control the residual activation to meet the requirements of hands-on maintenance, a two-stage collimation system has been designed for the RCS. The collimation system consists of one primary collimator made of thin metal to scatter the beam and four secondary collimators as absorbers. Thermal analysis is an important aspect in evaluating the reliability of the collimation system. The calculation of the temperature distribution and thermal stre…
The injection system of the China Spallation Neutron Source uses H- stripping and phase space painting method to fill large ring acceptance with the linac beam of small emittance. The emittance evolution, beam losses, and collimation efficiency during the injection procedures for different injection parameters, such as the injection emittances, starting injection time, twiss parameters and momentum spread, were studied, and then the optimized injection parameters was obtained. In addition, the phase space painting scheme which also affect the emittance evolution and beam losses were simulated …
China Spallation Neutron Source is a high intensity proton accelerator based facility, and its accelerator complex includes two main parts an H- linac and a rapid cycling synchrotron. The RCS accumulates the 80MeV proton beam, and accelerates it to 1.6GeV, with a repetition rate of 25Hz. The dipole of the CSNS RCS is operated at a 25 Hz sinusoidal alternating current which causes severe vibrate. The vibration will influence the long term safety and reliable operation of the magnet. The dipole of the CSNS RCS is an active vibration equipment which is different from the ground vibration accelera…
China spallation neutron source(CSNS) is a high intensity proton accelerator based facility, and its accelerator complex includes two main parts: an H- linac and a rapid cycling synchrotron(RCS). The rcs accumulates the 80MeV proton beam, and accelerates it to 1.6GeV, with a repetition rate of 25 Hz. The AC dipole of the RCS is operated at a 25Hz sinusoidal alternating current which causes severe vibration. The vibration will influence the long-term safety and reliable operation of the magnet. The dipole magnet of RCS is active vibration equipment which is different with ground vibration accel…
Electron cloud interaction with high energy positive beam are believed responsible for various undesirable effects such as vacuum degradation, collective beam instability and even beam loss in high power proton circular accelerator. An important uncertainty in predicting electron cloud instability lies in the detail processes on the generation and accumulation of the electron cloud. The simulation on the build-up of electron cloud is necessary to further studies on beam instability caused by electron cloud. China Spallation Neutron Source (CSNS) is the largest scientific project in building, w…
In order to update the beam power from 100 kW to 250 kW in China spallation neutron source (CSNS) Phase II, one of the important measures is to replace the 80 meters long beam transport line between the present 80 MeV linac injector and the RCS to another kind of acceleration structure. In this paper, we proposed a scheme based on 324 MHz double-spoke superconducting cavities. Unlike the superconducting elliptical cavity and normal conducting CCL structure, the double-spoke cavity belongs to TE mode structure and has smaller transvers dimension compared with that of TH mode one. It can work at…
