It is shown that an optical parametric amplifier inside a cavity can considerably improve the cooling of the micromechanical mirror by radiation pressure. The micromechanical mirror can be cooled from room temperature 300 K to sub-Kelvin temperatures, which is much lower than what is achievable in the absence of the parametric amplifier. Further if in case of a precooled mirror one can reach millikelvin temperatures starting with about 1 K. Our work demonstrates the fundamental dependence of radiation pressure effects on photon statistics.
We propose a quantum description of the cooling of a micromechanical flexural oscillator by a one-dimensional transmission line resonator via a force that resembles cavity radiation pressure. The mechanical oscillator is capacitively coupled to the central conductor of the transmission line resonator. At the optimal point, the micromechanical oscillator can be cooled close to the ground state, and the cooling can be measured by homodyne detection of the output microwave signal.
We cool the fundamental mode of a miniature cantilever by capacitively coupling it to a driven rf resonant circuit. Cooling results from the rf capacitive force, which is phase shifted relative to the cantilever motion. We demonstrate the technique by cooling a 7 kHz cantilever from room temperature to 45 K, obtaining reasonable agreement with a model for the cooling, damping, and frequency shift. Extending the method to higher frequencies in a cryogenic system could enable ground state cooling and may prove simpler than related optical experiments in a low temperature apparatus.
Cooling a mesoscopic mechanical oscillator to its quantum ground state is elementary for the preparation and control of low entropy quantum states of large scale objects. Here, we pre-cool a 70-MHz micromechanical silica oscillator to an occupancy below 200 quanta by thermalizing it with a 600-mK cold 3He gas. Two-level system induced damping via structural defect states is shown to be strongly reduced, and simultaneously serves as novel thermometry method to independently quantify excess heating due to the cooling laser. We demonstrate that dynamical backaction sideband cooling can reduce the…
We propose a theoretical scheme to show the possibility of achieving the quantum ground state cooling of a vibrating micromechanical membrane inside a high finesse optical cavity by back-action cooling approach. The scheme is based on an intensity-dependent coupling of the membrane to the intracavity radiation pressure field. We find the exact expression for the position and momentum variances of the membrane by solving the linearized quantum Langevin equations in the steady-state, conditioned by the Routh-Hurwitz criterion. We show that by varying the Lamb-Dicke parameter and the membrane's r…
Ground state cooling of micromechanical oscillator is a paradigmatic goal for observing quantum mechanical effects in cavity optomechanics. We study theoretically the ground state cooling of a mechanical oscillator in an optomechanical cavity in presence of a quantum well placed inside the cavity. Due to mode tailoring in presence of the quantum well, the cavity response gets modified and leads to asymmetric heating and cooling processes. This facilitates the cooling of the mechanical oscillator even in the unresolved-sideband regime, via inhibition of Stokes scattering.
We theoretically investigate the stability of a two cascaded cavity optomechanical system with optical parametric amplifiers (OPAs) inside the two coupled cavities, and study the steady-state entanglement between two distant mechanical resonators. We show that the parameter regime where the system is unstable without OPAs, such as relatively high laser intensity and blue detuning, can be exploited to build the steady-state mechanical entanglement by modulating the parametric gain. The application of OPAs is helpful to preserve the mechanical entanglement suffered from the dissipation at some f…
The radiation pressure of light can act to damp and cool the vibrational motion of a mechanical resonator. In understanding the quantum limits of this cooling, one must consider the effect of shot noise fluctuations on the final thermal occupation. In optomechanical sideband cooling in a cavity, the finite Stokes Raman scattering defined by the cavity linewidth combined with shot noise fluctuations dictates a quantum backaction limit, analogous to the Doppler limit of atomic laser cooling. In our work we sideband cool to the quantum backaction limit by using a micromechanical membrane precoole…
The ground state cooling of a mechanical oscillator in an optomechanical cavity containing an ensemble of identical two-level ground-state atoms is studied in the highly unresolved-sideband regime. The system exhibits electromagnetically-induced transparency-like quantum interference effect. The mutual interaction with the cavity optical field gives rise to an indirect coupling between the atomic and mechanical modes. In presence of this interaction, the noise spectrum gets modified and leads to asymmetric cooling and heating rates. Using the quantum master equation, time evolution of the aver…
We provide a general framework to describe cooling of a micromechanical oscillator to its quantum ground state by means of radiation-pressure coupling with a driven optical cavity. We apply it to two experimentally realized schemes, back-action cooling via a detuned cavity and cold-damping quantum-feedback cooling, and we determine the ultimate quantum limits of both schemes for the full parameter range of a stable cavity. While both allow to reach the oscillator's quantum ground state, we find that back-action cooling is more efficient in the good cavity limit, i.e. when the cavity bandwidth …
Multimode optomechanical systems are an emerging platform for studying fundamental aspects of matter near the quantum ground state and are useful in sensitive sensing and measurement applications. We study optomechanical cooling in a system where two nearly degenerate mechanical oscillators are coupled to a single microwave cavity. Due to an optically mediated coupling the two oscillators hybridize into a bright mode with strong optomechanical cooling rate and a dark mode nearly decoupled from the system. We find that at high coupling, sideband cooling of the dark mode is strongly suppressed. …
The advent of laser cooling techniques revolutionized the study of many atomic-scale systems. This has fueled progress towards quantum computers by preparing trapped ions in their motional ground state, and generating new states of matter by achieving Bose-Einstein condensation of atomic vapors. Analogous cooling techniques provide a general and flexible method for preparing macroscopic objects in their motional ground state, bringing the powerful technology of micromechanics into the quantum regime. Cavity opto- or electro-mechanical systems achieve sideband cooling through the strong interac…
We investigate a setup where a cloud of atoms is trapped in an optical lattice potential of a standing wave laser field which is created by retro-reflection on a micro-membrane. The membrane vibrations itself realize a quantum mechanical degree of freedom. We show that the center of mass mode of atoms can be coupled to the vibrational mode of the membrane in free space, and predict a significant sympathetic cooling effect of the membrane when atoms are laser cooled. The controllability of the dissipation rate of the atomic motion gives a considerable advantage over typical optomechanical syste…
Micro- and nanoscale opto-mechanical systems provide radiation pressure coupling of optical and mechanical degree of freedom and are actively pursued for their ability to explore quantum mechanical phenomena of macroscopic objects. Many of these investigations require preparation of the mechanical system in or close to its quantum ground state. Remarkable progress in ground state cooling has been achieved for trapped ions and atoms confined in optical lattices. Imperative to this progress has been the technique of resolved sideband cooling, which allows overcoming the inherent temperature limi…
We perform an analysis of the optomechanical entanglement between the experimentally detectable output field of an optical cavity and a vibrating cavity end-mirror. We show that by a proper choice of the readout (mainly by a proper choice of detection bandwidth) one can not only detect the already predicted intracavity entanglement but also optimize and increase it. This entanglement is explained as being generated by a scattering process owing to which strong quantum correlations between the mirror and the optical Stokes sideband are created. All-optical entanglement between scattered sideban…
The observation of quantum phenomena in macroscopic mechanical oscillators has been a subject of interest since the inception of quantum mechanics. Prerequisite to this regime are both preparation of the mechanical oscillator at low phonon occupancy and a measurement sensitivity at the scale of the spread of the oscillator's ground state wavefunction. It has been widely perceived that the most promising approach to address these two challenges are electro nanomechanical systems. Here we approach for the first time the quantum regime with a mechanical oscillator of mesoscopic dimensions--discer…
We discuss a hybrid quantum system where a dielectric membrane situated inside an optical cavity is coupled to a distant atomic ensemble trapped in an optical lattice. The coupling is mediated by the exchange of sideband photons of the lattice laser, and is enhanced by the cavity finesse as well as the square root of the number of atoms. In addition to observing coherent dynamics between the two systems, one can also switch on a tailored dissipation by laser cooling the atoms, thereby allowing for sympathetic cooling of the membrane. The resulting cooling scheme does not require resolved sideb…
Cavity optomechanics provides a unique platform for controlling micromechanical systems by means of optical fields that crosses the classical-quantum boundary to achieve solid foundations for quantum technologies. Currently, optomechanical resonators have become promising candidates for the development of precisely controlled nano-motors, ultrasensitive sensors and robust quantum information processors. For all these applications, a crucial requirement is to cool the mechanical resonators down to their quantum ground states. In this paper, we present a novel cooling scheme to further cool a mi…
Cooling forces result from the retarded dipole interaction between an illuminated particle and its reflection. For a one-dimensional example, we find cooling times of milliseconds and limiting temperatures in the millikelvin range. The force, which may be considered the prototype for cavity-mediated cooling, may be enhanced by plasmon and geometric resonances at the mirror.
We propose a technique aimed at cooling a harmonically oscillating mirror to its quantum mechanical ground state starting from room temperature. Our method, which involves the two-sided irradiation of the vibrating mirror inside an optical cavity, combines several advantages over the two-mirror arrangements being used currently. For comparable parameters the three-mirror configuration provides a stiffer trap for the oscillating mirror. Furthermore it prevents bistability from limiting the use of higher laser powers for mirror trapping, and also partially does so for mirror cooling. Lastly, it …
We describe an experiment in which a mirror is cooled by the radiation pressure of light. A high-finesse optical cavity with a mirror coated on a mechanical resonator is used as an optomechanical sensor of the Brownian motion of the mirror. A feedback mechanism controls this motion via the radiation pressure of a laser beam reflected on the mirror. We have observed either a cooling or a heating of the mirror, depending on the gain of the feedback loop.
We consider the radiative trapping and cooling of a partially transmitting mirror suspended inside an optical cavity, generalizing the case of a perfectly reflecting mirror previously considered [M. Bhattacharya and P. Meystre, Phys. Rev. Lett. \textbf{99}, 073601 (2007)]. This configuration was recently used in an experiment to cool a nanometers-thick membrane [Thompson \textit{et al.}, arXiv:0707.1724v2, 2007]. The self-consistent cavity field modes of this system depend strongly on the position of the middle mirror, leading to important qualitative differences in the radiation pressure effe…
We develop a theory of quantum feedback cooling of a single ion trapped in front of a mirror. By monitoring the motional sidebands of the light emitted into the mirror mode we infer the position of the ion, and act back with an appropriate force to cool the ion. We derive a feedback master equation along the lines of the quantum feedback theory developed by Wiseman and Milburn, which provides us with cooling times and final temperatures as a function of feedback gain and various system parameters.
We investigate a hybrid optomechanical system comprised of a mechanical oscillator and an atomic 3-level ensemble within an optical cavity. We show that a suitably tailored cavity field response via Electromagnetically Induced Transparency (EIT) in the atomic medium allows for strong coupling of the mechanical mirror oscillations to the collective atomic ground-state spin. This facilitates ground-state cooling of the mirror motion, quantum state mapping and robust atom-mirror entanglement even for cavity widths larger than the mechanical oscillator frequency.
We investigate the response of a harmonically confined mirror to an optical pulse in cavity optomechanics. We show that when the pulsed coupling strength takes the form of a chirped pulse, thermal fluctuations of the mirror can be significantly transferred to the cavity field. In addition, the frequency modulation of the pulse could enable a better cooling performance by suppressing the sensitivity of the dependence of detuning and pulse areas. Using numerical investigations, we find that the pulsed-cooling is mainly limited by the cavity-field decay rate.
We show that one can cool a micro-mechanical oscillator to its quantum ground state using radiation pressure in an appropriately detuned cavity (self-cooling). From a simple theory based on Heisenberg-Langevin equations we find that optimal self-cooling occurs in the good cavity regime, when the cavity bandwidth is smaller than the mechanical frequency, but still larger than the effective mechanical damping. In this case the intracavity field and the vibrational mechanical mode coherently exchange their fluctuations. We also present dynamical calculations which show how to access the mirror fi…
We propose a theoretical scheme for atomic cooling, i.e. the compression of both velocity and position distribution of particles in motion. This is achieved by collisions of the particles with a combination of a moving atomic mirror and a moving atom diode. An atom diode is a unidirectional barrier, i.e. an optical device through which an atom can pass in one direction only. We show that the efficiency of the scheme depends on the trajectory of the diode and the mirror. We examine both the classical and quantum mechanical descriptions of the scheme, along with the numerical simulations to show…
We investigate the effects of atomic collisions as well as optomechanical mirror-field coupling on the optical bistability in a hybrid system consisting of a Bose-Einstein condensate inside a driven optical cavity with a moving end mirror. It is shown that the bistability of the system can be controlled by the s-wave scattering frequency which can provide the possibility of realizing a controllable optical switch. On the other hand, by studying the effect of the Bogoliubov mode, as a secondary mechanical mode relative to the mirror vibrations, on the cooling process as well as the bipartite mi…
We demonstrate passive feedback cooling of a mechanical resonator based on radiation pressure forces and assisted by photothermal forces in a high-finesse optical cavity. The resonator is a free-standing high-reflectance micro-mirror (of mass m=400ng and mechanical quality factor Q=10^4) that is used as back-mirror in a detuned Fabry-Perot cavity of optical finesse F=500. We observe an increased damping in the dynamics of the mechanical oscillator by a factor of 30 and a corresponding cooling of the oscillator modes below 10 K starting from room temperature. This effect is an important ingredi…
Recent experimental progress in table-top experiments or gravitational-wave interferometers has enlightened the unique displacement sensitivity offered by optical interferometry. As the mirrors move in response to radiation pressure, higher power operation, though crucial for further sensitivity enhancement, will however increase quantum effects of radiation pressure, or even jeopardize the stable operation of the detuned cavities proposed for next-generation interferometers. The appearance of such optomechanical instabilities is the result of the nonlinear interplay between the motion of the …
We demonstrate a simple and robust geometry for optical trapping in vacuum of a single nanoparticle based on a parabolic mirror and the optical gradient force, and we demonstrate rapid parametric feedback cooling of all three motional degrees of freedom from room temperature to a few mK. A single laser at 1550nm, and a single photodiode, are used for trapping, position detection, and cooling for all three dimensions. Particles with diameters from 26nm to 160nm are trapped without feedback to 10$^{-5}$mbar and with feedback engaged the pressure is reduced to 10$^{-6}$mbar. Modifications to the …
We theoretically study the radiation-induced interaction between the mechanical motion of an oscillating mirror and a remotely trapped atomic cloud. When illuminated by continuous-wave radiation, the mirror motion will induce red and blue sideband radiation, which respectively increases and reduces motional excitation. We find that by suitably driving $Λ$-level atoms, the mirror correlation with a specific radiation sideband could be converted from the outgoing to the incoming radiation. Such process allows us to manipulate the heating and cooling effects. Particularly, we develop an optomecha…
We discuss how the optomechanical coupling provided by radiation pressure can be used to cool macroscopic collective degrees of freedom, as vibrational modes of movable mirrors. Cooling is achieved using a phase-sensitive feedback-loop which effectively overdamps the mirrors motion without increasing the thermal noise. Feedback results able to bring macroscopic objects down to the quantum limit. In particular, it is possible to achieve squeezing and entanglement.
We predict ground state cooling of a micro-mechanical oscillator, i.e. a vibrating end-mirror of an optical cavity, by resonant coupling of mirror vibrations to a narrow internal optical transition of an ensemble of two level systems. The particles represented by a collective mesoscopic spin model implement, together with the cavity, an efficient, frequency tailorable zero temperature loss channel which can be turned to a gain channel of pump. As opposed to the case of resolved-sideband cavity cooling requiring a small cavity linewidth, one can work here with low finesses and very small cavity…
Macroscopic mechanical objects and electromagnetic degrees of freedom couple to each other via radiation pressure. Optomechanical systems with sufficiently strong coupling are predicted to exhibit quantum effects and are a topic of considerable interest. Devices reaching this regime would offer new types of control of the quantum state of both light and matter and would provide a new arena in which to explore the boundary between quantum and classical physics. Experiments to date have achieved sufficient optomechanical coupling to laser-cool mechanical devices but have not yet reached the quan…
We present a one-dimensional scattering theory which enables us to describe a wealth of effects arising from the coupling of the motional degree of freedom of scatterers to the electromagnetic field. Multiple scattering to all orders is taken into account. The theory is applied to describe the scheme of a Fabry-Perot resonator with one of its mirrors moving. The friction force, as well as the diffusion, acting on the moving mirror is derived. In the limit of a small reflection coefficient, the same model provides for the description of the mechanical effect of light on an atom moving in front …
We present a new micromechanical resonator designed for cavity optomechanics. We have used a micropillar geometry to obtain a high-frequency mechanical resonance with a low effective mass and a very high quality factor. We have coated a 60-$μ$m diameter low-loss dielectric mirror on top of the pillar and are planning to use this micromirror as part of a high-finesse Fabry-Perot cavity, to laser cool the resonator down to its quantum ground state and to monitor its quantum position fluctuations by quantum-limited optical interferometry.
We propose a feasible scheme to cool down a mechanical resonator (MR) in a three-mirror cavity optomechanical system with controllable external optical drives. Under the Born-Oppenheimer (BO) approximation, the whole dynamics of the mechanical resonator and cavities is reduced to that of a time-dependent harmonic oscillator, whose effective frequency can be controlled through the optical driving fields. The fast cooling of the MR can be realized by controlling the amplitude of the optical drives. Significantly, we further show that the ground-state cooling may be achieved via the three-mirror …
We consider the dynamics of a movable mirror (cantilever) of a nonlinear optical cavity. We show that a $χ^{(3)}$ medium with a strong Kerr nonlinearity placed inside a cavity inhibits the normal mode splitting (NMS) due to the photon blockade mechanism. This study demonstrates that NMS could be used as a tool to observe the photon blockade effect. We also found that the backaction cooling of the movable mirror is reduced in the presence of the Kerr medium.
I discuss the robustness of the pumped cavity dynamics against phase diffusion of the laser and conclude that opto-mechanical cooling has extreme sensitivity compared to laser cooling of atoms. Certain proposals of ground state opto-mechanical cooling by single cavity would require an unrealistic sharp laser linewidth or equivalently, a very low level of phase noise. A systematic way to cancel classical excess phase noise is the interferometric twin-cavity pumping, initiated for optically trapped macro-mirrors of future gravitational-wave detectors.
We investigate the creation of squeezed states of a vibrating membrane or a movable mirror in an opto-mechanical system. An optical cavity is driven by squeezed light and couples via radiation pressure to the membrane/mirror, effectively providing a squeezed heat-bath for the mechanical oscillator. Under the conditions of laser cooling to the ground state, we find an efficient transfer of squeezing with roughly 60% of light squeezing conveyed to the membrane/mirror (on a dB scale). We determine the requirements on the carrier frequency and the bandwidth of squeezed light. Beyond the conditions…
The Born-Markov master equation analysis of the vibrating mirror and photon experiment proposed by Marshall, Simon, Penrose and Bouwmeester is completed by including the important issues of temperature and friction. We find that at the level of cooling available to date, visibility revivals are purely classical, and no quantum effect can be detected by the setup, no matter how strong the photon-mirror coupling is. Checking proposals of universal nonenvironmental decoherence is ruled out by dominating thermal decoherence; a conjectured coordinate-diffusion contribution to decoherence may become…
We review the field of cavity optomechanics, which explores the interaction between electromagnetic radiation and nano- or micromechanical motion. This review covers the basics of optical cavities and mechanical resonators, their mutual optomechanical interaction mediated by the radiation pressure force, the large variety of experimental systems which exhibit this interaction, optical measurements of mechanical motion, dynamical backaction amplification and cooling, nonlinear dynamics, multimode optomechanics, and proposals for future cavity quantum optomechanics experiments. In addition, we d…
We theoretically analyze the cooling dynamics of an atom which is tightly trapped inside a high-finesse optical resonator. Cooling is achieved by suitably tailored scattering processes, in which the atomic dipole transition either scatters a cavity photon into the electromagnetic field external to the resonator, or performs a stimulated emission into the cavity mode, which then dissipates via the cavity mirrors. We identify the parameter regimes in which the atom center-of-mass motion can be cooled into the ground state of the external trap. We predict, in particular, that for high cooperativi…
We investigate the squeezing for a movable mirror in the dissipative optomechanics in which the oscillating mirror modulates both the resonance frequency and the linewidth of the cavity mode. Via feeding a much weaker broadband squeezed vacuum light accompanying the coherent driving laser field into the cavity, the master equation for the cavity-mirror system is derived by following the general reservoir theory based on the density operator in which the reservoir variables are adiabatically eliminated by using the reduced density operator for the system in the interaction picture. When the mir…
We report a spin-orbit coupling induced back-action cooling in an optomechanical system, composed of a spin-orbit coupled Bose-Einstein condensate trapped in an optical cavity with one movable end mirror, by suppressing heating effects of quantum noises. The collective density excitations of the spin-orbit coupling mediated hyperfine states - serving as atomic oscillators equally coupled to the cavity field - trigger strongly driven atomic back-action. We find that the back-action not only revamps low-temperature dynamics of its own but also provides an opportunity to cool the mechanical mirro…
We report on use of a radiation pressure induced restoring force, the optical spring effect, to optically dilute the mechanical damping of a 1 gram suspended mirror, which is then cooled by active feedback (cold damping). Optical dilution relaxes the limit on cooling imposed by mechanical losses, allowing the oscillator mode to reach a minimum temperature of 6.9 mK, a factor of ~40000 below the environmental temperature. A further advantage of the optical spring effect is that it can increase the number of oscillations before decoherence by several orders of magnitude. In the present experimen…
We report an efficient mechanism to generate a squeezed state of a mechanical mirror in an optomechanical system. We use especially tuned parametric amplifier (PA) inside the cavity and the parametric photon phonon processes to transfer quantum squeezing from photons to phonons with almost 100\% efficiency. We get 50\% squeezing of the mechanical mirror which is limited by the PA. We present analytical results for the mechanical squeezing thus enabling one to understand the dependence of squeezing on system parameters like gain of PA, cooperativity, temperature. As in cooling experiments the d…
In this paper we present a model for the kinematics and dynamics of optomechanics which describe the coupling between an optical field, here modeled by a massless scalar field, and the internal (e.g., determining its reflectivity) and mechanical (e.g., displacement) degrees of freedom of a moveable mirror. As opposed to implementing boundary conditions on the field we highlight the internal dynamics of the mirror which provides added flexibility to describe a variety of setups relevant to current experiments. The inclusion of the internal degrees of freedom in this model allows for a variety o…
We review recent progress in the field of optomechanics, where one studies the effects of radiation on mechanical motion. The paradigmatic example is an optical cavity with a movable mirror, where the radiation pressure can induce cooling, amplification and nonlinear dynamics of the mirror.
A cavity optomechanical system is initiated by a radiation pressure of a cavity field onto a mirror element acting as a quantum resonator. This radiation pressure can control the thermodynamic character of the mirror to some extent, such as cooling its effective temperature. Here we show that by properly engineering the spectral density of a thermal heat bath that interacts with a quantum system, the evolution of the quantum system can be effectively turned on and off. Inside a cavity optomechanical system, when the heat bath is realized by a multi-mode oscillator modeling of the mirror, this …
Many protocols in quantum science and technology require initializing a system in a pure quantum state. In the context of the motional state of massive resonators, this enables studying fundamental physics at the elusive quantum-classical transition, and measuring force and acceleration with enhanced sensitivity. Laser cooling has been a method of choice to prepare mechanical resonators in the quantum ground state, one of the simplest pure states. However, in order to overcome the heating and decoherence by the thermal bath, this usually has to be combined with cryogenic cooling. Here, we lase…
We theoretically investigate the coupling of an ultracold three-level atomic gas and a nano-mechanical mirror via classical electromagnetic radiation. The radiation pressure on the mirror is modulated by absorption of a probe light field, caused by the atoms which are electromagnetically rendered nearly transparent, allowing the gas to affect the mirror. In turn, the mirror can affect the gas as its vibrations generate opto-mechanical sidebands in the control field. We show that the sidebands cause modulations of the probe intensity at the mirror frequency, which can be enhanced near atomic re…
We present a general framework for cavity quantum electrodynamics with strongly frequency-dependent mirrors. The method is applicable to a variety of reflectors exhibiting sharp internal resonances as can be realized, for example, with photonic-crystal mirrors or with two-dimensional atomic arrays around subradiant points. Our approach is based on a modification of the standard input--output formalism to explicitly include the dynamics of the mirror's internal resonance. We show how to directly extract the interaction tuning parameters from the comparison with classical transfer matrix theory …
Optical cavity cooling of mechanical resonators has recently become a research frontier. The cooling has been realized with a metal-coated silicon microlever via photo-thermal force and subsequently with dielectric objects via radiation pressure. Here we report cavity cooling with a crystalline semiconductor membrane via a new mechanism, in which the cooling force arises from the interaction between the photo-induced electron-hole pairs and the mechanical modes through the deformation potential coupling. The optoelectronic mechanism is so efficient as to cool a mode down to 4 K from room tempe…
Ground-state cooling of mechanical motion by coupling to a driven optical cavity has been demonstrated in various optomechanical systems. In our work, we provide a so far missing thermodynamic performance analysis of optomechanical sideband cooling in terms of a heat valve. As performance quantifiers, we examine not only the lowest reachable effective temperature (phonon number) but also the evacuated-heat flow as an equivalent to the cooling power of a standard refrigerator, as well as appropriate thermodynamic efficiencies, which all can be experimentally inferred from measurements of the ca…
